Two CATALYST 2900XL

Discussion in 'Cisco' started by Marcin Gaszewski, May 28, 2004.

  1. Hi
    I tried to connect two Cisco 2900XL switches using cross-over cable.
    Lights didn't start to flash when I pluged cable to ports.
    Below are both switches ports interface info.
    Can you help me, please?
    Thans a lot

    switch-1#show interfaces FastEthernet 0/20
    FastEthernet0/20 is down, line protocol is down
    Hardware is Fast Ethernet, address is 0030.8055.e6d4 (bia 0030.8055.e6d4)
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive not set
    Auto-duplex , Auto Speed , 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input never, output 1d00h, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    1 packets input, 64 bytes
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog, 0 multicast
    0 input packets with dribble condition detected
    6 packets output, 2013 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    SWITCH-2#show interfaces FastEthernet 0/24
    FastEthernet0/24 is down, line protocol is down
    Hardware is Fast Ethernet, address is 0001.429b.7718 (bia 0001.429b.7718)
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive not set
    Auto-duplex , Auto Speed , 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input never, output 1d01h, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    1 packets input, 64 bytes
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog, 0 multicast
    0 input packets with dribble condition detected
    5 packets output, 1559 bytes, 0 underruns
    0 output errors, 0 collisions, 3 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    Conf it's standard without trunks.
    Marcin
     
    Marcin Gaszewski, May 28, 2004
    #1
    1. Advertisements

  2. first things first, try specifying 100mb and full-duplex and verify the
    pinouts on the crossover cable.
     
    Richard R. Field, May 28, 2004
    #2
    1. Advertisements

  3. If that's the output when the cable is plugged in then you probably have a
    bad cable.

    JR
     
    Johnny Routin, May 28, 2004
    #3
  4. Dnia Fri, 28 May 2004 15:13:45 -0400, Johnny Routin napisa³(a):
    i set
    duplex full
    speed 100
    and i had only one up interface.
    second it's still down

    best regards
    Marcin
     
    Marcin Gaszewski, May 29, 2004
    #4
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.