[new user]

Discussion in 'Cisco' started by myname, Apr 14, 2005.

  1. myname

    myname Guest

    Hello folks,
    it's first time that I use a cisco 801 and my boss wants the work the
    newt week. So, I need help.

    Some days ago I loaded on my windows machine rhe "cisco fast step" and I
    guessed for a new machine using the coinsolle cable.

    The cisco software found the cisco 801 bu ask me the old password...
    this is an old machine that my boss gave to me to progamming again the
    machine so I can also reset all data into this cisco, otherwise I can
    try with default user and password.

    Can you help me?
    What are the factory user name, read password and read/write password?
    How can I reset the machine?

    Thank you very much.
     
    myname, Apr 14, 2005
    #1
    1. Advertisements

  2. www.networking-forum.com, Apr 14, 2005
    #2
    1. Advertisements

  3. myname

    myname Guest

    Thanks but it don't work :(! I'm using Windows Hyperterminal and the key
    breack and SHIFT-F6 to get the break command.

    It's what I can see after 60 seconds... (when I press break the state is
    freezed... no more events...)


    01:17:39: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?

    01:18:39: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?


    TinyROM version 1.4(1)
    19:37 11/07/00
    Copyright (c) 1998-2000 by cisco Systems, Inc.

    All rights reserved.

    POST ............ OK. 4MB DRAM, 8MB Flash.


    Configured boot failed, attempting fallback boot.


    Booting "c800-y6-mw.122-8.T5.bin" ...,
    Restricted Rights Legend


    Use, duplication, or disclosure by the Government is

    subject to restrictions as set forth i
    (c) of the Commercial Computer Software - Restricted

    Rights clause at FAR sec. 52.227-19 and subparagraph

    (c) (1) (ii) of the Rights in Technical Data and Computer

    Software clause at DFARS sec. 252.227-7013.


    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706




    Cisco Internetwork Operating System Software

    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)

    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Syst
    Compiled Fri 21-Jun-02 11:25 by ccai
    Image text-base: 0x000F5000, data-base: 0x0077F000


    Cisco C801 (MPC850) processor (revision 1) with 44156K bytes of virtual
    memory.


    Processor board ID JAD064000RM (366422497)

    CPU part number 0x2101
    Bridging software.
    Basic Rate ISDN software, Version 1.1.
    1 Ethernet/IEEE 802.3 interface(s)
    1 ISDN Basic Rate interface(s)
    4M bytes of physical memory (DRAM)
    8K bytes of non-volatile configuration memory

    8M bytes of flash on board (4M from flash card)




    Press RETURN to get started!


    00:00:23: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up

    00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta

    te to up
    00:00:28: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?

    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
    changed state

    to down
    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2,
    changed state

    to down
    00:00:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta

    te to down
    00:00:32: %SYS-5-CONFIG_I: Configured from memory by console

    00:00:33: %SYS-5-RESTART: System restarted --

    Cisco Internetwork Operating System Software

    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)

    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Systems, Inc.

    Compiled Fri 21-Jun-02 11:25 by ccai
    00:00:33: %SNMP-5-COLDSTART: SNMP agent on host router is undergoing a
    cold star

    t
    00:00:34: %LINK-3-UPDOWN: Interface BRI0, changed state to up

    00:01:38: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?

    00:02:38: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?


    TinyROM version 1.4(1)
    19:37 11/07/00
    Copyright (c) 1998-2000 by cisco Systems, Inc.

    All rights reserved.

    POST ............ OK. 4MB DRAM, 8MB Flash.


    Configured boot failed, attempting fallback boot.


    Booting "c800-y6-mw.122-8.T5.bin" ...,
    Restricted Rights Legend


    Use, duplication, or disclosure by the Government is

    subject to restrictions as set forth i
    (c) of the Commercial Computer Software - Restricted

    Rights clause at FAR sec. 52.227-19 and subparagraph

    (c) (1) (ii) of the Rights in Technical Data and Computer

    Software clause at DFARS sec. 252.227-7013.


    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706




    Cisco Internetwork Operating System Software

    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)

    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Syst
    Compiled Fri 21-Jun-02 11:25 by ccai
    Image text-base: 0x000F5000, data-base: 0x0077F000


    Cisco C801 (MPC850) processor (revision 1) with 44156K bytes of virtual
    memory.


    Processor board ID JAD064000RM (366422497)

    CPU part number 0x2101
    Bridging software.
    Basic Rate ISDN software, Version 1.1.
    1 Ethernet/IEEE 802.3 interface(s)
    1 ISDN Basic Rate interface(s)
    4M bytes of physical memory (DRAM)
    8K bytes of non-volatile configuration memory

    8M bytes of flash on board (4M from flash card)




    Press RETURN to get started!


    00:00:23: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up

    00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta

    te to up
    00:00:28: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?

    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
    changed state

    to down
    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2,
    changed state

    to down
    00:00:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta

    te to down
    00:00:32: %SYS-5-CONFIG_I: Configured from memory by console

    00:00:33: %SYS-5-RESTART: System restarted --

    Cisco Internetwork Operating System Software

    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)

    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Systems, Inc.

    Compiled Fri 21-Jun-02 11:25 by ccai
    00:00:33: %SNMP-5-COLDSTART: SNMP agent on host router is undergoing a
    cold star

    t
    00:00:34: %LINK-3-UPDOWN: Interface BRI0, changed state to up



    TinyROM version 1
    19:37 11/07/00
    Copyright (c) 1998-2000 by cisco Systems, Inc.

    All rights reserved.

    POST ............ OK. 4MB DRAM, 8MB Flash.


    Configured boot failed, attempting fallback boot.


    Booting "c800-y6-mw.122-8.T5.bin" ...,
    Restricted Rights Legend


    Use, duplication, or disclosure by the Government is

    subject to restrictions as set forth in subparagraph

    (c) of the Commercial Computer Software - Restricted

    Rights clause at FAR sec. 52.227-19 and subparagraph

    (c) (1) (ii) of the Rights in Technical Data and

    Software clause at DFARS sec. 252.227-7013.


    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706




    Cisco Internetwork Operating System Software

    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)

    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Systems, Inc.

    Compiled Fri 21-Jun-02 11:25 by ccai
    Image text-base: 0x000F5000, data-base: 0x0077F000


    Cisco C801 (MPC850) processor (revision 1) with 44156K bytes of v


    Processor board ID JAD064000RM (366422497)

    CPU part number 0x2101
    Bridging software.
    Basic Rate ISDN software, Version 1.1.
    1 Ethernet/IEEE 802.3 interface(s)
    1 ISDN Basic Rate interface(s)
    4M bytes of physical memory (DRAM)
    8K bytes of non-volatile configuration memory

    8M bytes of flash on board (4M from flash card)




    Press RETURN to get started!


    00:00:23: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
    00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta
    te to up
    00:00:28: %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1,
    changed state
    to down
    00:00:28: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2,
    changed state
    to down
    00:00:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
    changed sta
    te to down
    00:00:32: %SYS-5-CONFIG_I: Configured from memory by console
    00:00:33: %SYS-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software
    IOS (tm) C800 Software (C800-Y6-MW), Version 12.2(8)T5, RELEASE
    SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2002 by cisco Systems, Inc.
    Compiled Fri 21-Jun-02 11:25 by ccai
    00:00:33: %SNMP-5-COLDSTART: SNMP agent on host router is undergoing a
    cold star
    t
    00:00:34: %LINK-3-UPDOWN: Interface BRI0, changed state to up

    THANKS
     
    myname, Apr 14, 2005
    #3
  4. myname

    polleke7 Guest

    polleke7, Apr 14, 2005
    #4
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.