How to find out what kind of GBIC is installed in the CAT switch.

Discussion in 'Cisco' started by simonTempler, Mar 1, 2006.

  1. simonTempler

    simonTempler Guest

    Is there a command to get an exact part number of the GBIC module
    installed in the SUP engine. I have 4500 series (native mode). I am
    looking for the same results when you issue "show modules" command. I
    tried "show port capabilities", it shows whenther it is SX ir RJ type
    of a port but no module type. Thanks for your help,
     
    simonTempler, Mar 1, 2006
    #1
    1. Advertisements

  2. simonTempler

    Merv Guest

    try "show idprom interface"
     
    Merv, Mar 1, 2006
    #2
    1. Advertisements

  3. simonTempler

    simonTempler Guest

    Hey thanks Merv, it works.
     
    simonTempler, Mar 2, 2006
    #3
  4. simonTempler

    Merv Guest

    Could you post the output as an example
     
    Merv, Mar 2, 2006
    #4
  5. simonTempler

    simonTempler Guest

    Here you go. It gets pretty detailed. I've used this command recently
    to get a chassis serial #. Very useful command, should not forget it so
    easily. Thanks.

    CAT4506SUP4#sh idprom interface gigabitEthernet 1/1
    GBIC Serial EEPROM Contents:
    Common Block:
    Identifier = GBIC [0x1]
    Extended Id = GBIC is compliant with MOD_DEF 7 [0x7]
    Connector = SC connector [0x1]
    Transceiver
    Speed = Not available [0x0]
    Media = Not available [0x0]
    Technology = Not available [0x0]
    Link Length = Not available [0x0]
    GE Comp Codes = 1000BASE-SX [0x1]
    SONET Comp Codes = Not available [0x0]
    Encoding = 8B10B [0x1]
    BR, Nominal = 1300000000 MHz
    Length(9u) in km = GBIC does not support single mode fibre, or the
    length
    must be determined from the transceiver
    technology.
    Length(9u) = GBIC does not support single mode fibre, or the
    length
    must be determined from the transceiver
    technology.
    Length(50u) = 500 m
    Length(62.5u) = 220 m
    Length(Copper) = GBIC does not support copper cables, or the length
    must
    be determined from the transceiver technology.
    Vendor name = AGILENT
    Vendor OUI = 0
    Vendor Part No. = HFBR-5601
    Vendor Part Rev. = 0000
    Wavelength = Not available
    CC_BASE = 0x3F

    Extended ID Fields
    Options = Loss of Signal implemented TX_FAULT signal
    implemented TX_DISABLE is implemented and disables the serial output
    [0x1A]
    BR, max = Unspecified
    BR, min = Unspecified
    Vendor Serial No. = 0V6032928061
    Date code = 030716
    Diag monitoring = Not implemented
    Rx pwr measuremnt = Optical Modulation Amplitude (OMA)
    Address change = Not required
    CC_EXT = 0x96

    Vendor Specific ID Fields:
    20B6CD40 2D 35 2E 37 34 30 31 31 2E 34 34 34 30 2E 30 30
    -5.74011.4440.00
    20B6CD50 30 30 2D 31 38 00 00 00 0C 00 00 00 00 00 D9 00
    00-18.........Y.


    SEEPROM contents (hex) size 128:
    0x0000 01 07 01 00 00 00 01 00 00 00 00 01 0D 00 00 00
    .................
    0x0010 32 16 00 00 41 47 49 4C 45 4E 54 20 20 20 20 20 2...AGILENT

    0x0020 20 20 20 20 00 00 00 00 48 46 42 52 2D 35 36 30
    .....HFBR-560
    0x0030 31 20 20 20 20 20 20 20 30 30 30 30 00 00 00 3F 1
    0000...?
    0x0040 00 1A 00 00 30 56 36 30 33 32 39 32 38 30 36 31
    .....0V6032928061
    0x0050 20 20 20 20 30 33 30 37 31 36 20 20 00 00 00 96 030716
    ....^V
    0x0060 2D 35 2E 37 34 30 31 31 2E 34 34 34 30 2E 30 30
    -5.74011.4440.00
    0x0070 30 30 2D 31 38 00 00 00 0C 00 00 00 00 00 D9 00
    00-18.........Y.
     
    simonTempler, Mar 2, 2006
    #5
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.