frame relay switch configuration issue

Discussion in 'Cisco' started by geekylinuxkid, Apr 9, 2007.

  1. Hey. I'm working on configuring my network in a multipoint frame relay
    configuration.

    Here is what i got.

    FR - 2522
    s3 - R3
    s4 - R4
    s5 - R5

    R3 - 3640
    s1/0 - FR

    R4 - 3640
    s1/0 - FR

    R5 - 3640
    s1/0 - FR



    FR config

    frame-relay switching
    !
    interface Serial3
    no ip address
    encapsulation frame-relay
    clockrate 64000
    frame-relay intf-type dce
    frame-relay route 304 interface Serial4 403
    frame-relay route 305 interface Serial5 503
    !
    interface Serial4
    no ip address
    encapsulation frame-relay
    clockrate 64000
    frame-relay intf-type dce
    frame-relay route 403 interface Serial3 304
    frame-relay route 405 interface Serial5 504
    !
    interface Serial5
    no ip address
    encapsulation frame-relay
    clockrate 64000
    frame-relay intf-type dce
    frame-relay route 503 interface Serial3 305
    frame-relay route 504 interface Serial4 405


    R3
    interface Serial1/0
    ip address 10.12.16.3 255.255.255.248
    encapsulation frame-relay
    no fair-queue


    R4
    interface Serial1/0
    ip address 10.12.16.4 255.255.255.248
    encapsulation frame-relay
    no dce-terminal-timing-enable
    no fair-queue


    R5
    interface Serial1/0
    ip address 10.12.16.5 255.255.255.248
    encapsulation frame-relay
    no dce-terminal-timing-enable
    no fair-queue



    from what ive read, this configuration is correct. let me know if you
    have any other configuration changes you would recommend.

    thanks.

    SPC Franklin, John Jay
    Network Operations
    4IBCT, 1ID
    FOB Falcon, Iraq
     
    geekylinuxkid, Apr 9, 2007
    #1
    1. Advertisements

  2. Why you don't define DLCI on R3, R4, and R5?

    Good luck,

    Mike
    CCNP, CCDP, CCSP, Cisco Voice, MCSE W2K, MCSE+I, Security+, etc.
    CCIE R&S (in progress), CCIE Voice (in progress)
     
    headsetadapter.com, Apr 9, 2007
    #2
    1. Advertisements


  3. well shouldnt the status on the circuits be Active? They are all
    showing inactive as of now. would the map statements on the spoke
    routers help solve the issue?


    Thanks!

    SPC Franklin, John Jay
    Network Operations
    4IBCT, 1ID
    FOB Falcon, Iraq
     
    geekylinuxkid, Apr 9, 2007
    #3
  4. The "active" state means that circuit is ESTABLISHED between "local" and
    "remote". So, if your "remote" is not connected, DLCI will be "inactive".

    Good luck,

    Mike
    CCNP, CCDP, CCSP, Cisco Voice, MCSE W2K, MCSE+I, Security+, etc.
    CCIE R&S (in progress), CCIE Voice (in progress)
     
    headsetadapter.com, Apr 9, 2007
    #4

  5. So with my configuration, the remote would be connected therefore the
    the dlci active. Am I correct with this statement? AFAIK, my
    configuration should work.. yes?

    Thanks.

    SPC Franklin, John Jay
    Network Operations
    4th IBCT, 1ID
    FOB Falcon, Iraq
     
    geekylinuxkid, Apr 9, 2007
    #5
  6. I determined the issue to be a bad NM-4A/S module in one of my
    routers. Everything is working correctly now.

    Thanks!

    SPC Franklin, John Jay
    Network Operations
    4th IBCT, 1ID
    FOB Falcon, Iraq
     
    geekylinuxkid, Apr 12, 2007
    #6
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.