Cisco 3640 PBX Gateway - E1 PRI, no voice ports

Discussion in 'VOIP' started by richardp, Jan 5, 2004.

  1. richardp

    richardp Guest

    Hi,
    I have a Cisco 3640 and would like to connect it as a ISDN/PRI gateway
    to MD110 PBX. According to Cisco VOIp gateway configuration guide: (
    http://www.cisco.com/application/pd.../ps278/c1237/ccmigration_09186a00800e6e6c.pdf
    ) I should be able to use Channelized E1 module in order to interface
    with the MD110 PBX. My configuration, IOS and hardware configuration
    match or exceed the guide. However no voice port "voice-port 1/0:15"
    is created and consequently I can not configure a dial-peer
    ("dial-peer 7", interfacing with PBX). Voice ports 3/0/0 – 3/1/1 are
    created as expected (FXS and FXO cards)
    My hardware/software is as follows:
    1 NM-1FE2CE1B
    1 VIC2FSO
    1 VIC2FSX

    IOS v.12.2(2)T

    Am I missing something or I should forget about the NM-1FE2CE1B module
    and go straight to NM-HDV type of solution?

    Thanks,

    Richard

    Show version output:

    Router#sh ver
    Cisco Internetwork Operating System Software
    IOS (tm) 3600 Software (C3640-JSX-M), Version 12.2(2)T, RELEASE
    SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
    Copyright (c) 1986-2001 by cisco Systems, Inc.
    Compiled Sun 03-Jun-01 00:28 by ccai
    Image text-base: 0x600089A8, data-base: 0x616C4000

    ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE
    SOFTWARE (fc
    1)
    ROM: 3600 Software (C3640-JSX-M), Version 12.2(2)T, RELEASE SOFTWARE
    (fc1)

    Router uptime is 0 minutes
    System returned to ROM by reload
    System image file is "flash:c3640-jsx-mz.122-2.T.bin"

    cisco 3640 (R4700) processor (revision 0x00) with 59392K/6144K bytes
    of memory.
    Processor board ID 07991029
    R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
    Channelized E1, Version 1.0.
    Bridging software.
    X.25 software, Version 3.0.0.
    SuperLAT software (copyright 1990 by Meridian Technology Corp).
    TN3270 Emulation software.
    Primary Rate ISDN software, Version 1.1.
    1 Ethernet/IEEE 802.3 interface(s)
    1 FastEthernet/IEEE 802.3 interface(s)
    32 Serial network interface(s)
    2 Channelized E1/PRI port(s)
    2 Voice FXO interface(s)
    2 Voice FXS interface(s)
    DRAM configuration is 64 bits wide with parity disabled.
    125K bytes of non-volatile configuration memory.
    32768K bytes of processor board System flash (Read/Write)

    Configuration register is 0x2102


    My show running output:

    Router#sh run
    Building configuration...

    Current configuration : 1405 bytes
    !
    version 12.2
    no parser cache
    no service single-slot-reload-enable
    service timestamps debug uptime
    service timestamps log uptime
    no service password-encryption
    !
    hostname Router
    !
    logging rate-limit console 10 except errors
    no logging console
    enable secret 5 $1$Dyxe$h0R8LHBz3O9Zq6NyQ3H6Q/
    !
    ip subnet-zero
    !
    no ip dhcp-client network-discovery
    isdn switch-type primary-net5
    call rsvp-sync
    !
    controller E1 1/0
    clock source internal
    pri-group timeslots 1-31
    !
    controller E1 1/1
    !
    interface Ethernet0/0
    ip address 10.21.121.121 255.255.0.0
    half-duplex
    !
    interface Serial0/0
    no ip address
    shutdown
    !
    interface FastEthernet1/0
    no ip address
    shutdown
    duplex auto
    speed auto
    !
    interface Serial1/0:15
    no ip address
    isdn switch-type primary-net5
    isdn overlap-receiving
    isdn protocol-emulate network
    isdn incoming-voice voice
    isdn T203 30000
    isdn T310 60000
    isdn bchan-number-order ascending
    no cdp enable
    !
    ip classless
    ip http server
    !
    snmp-server manager
    !
    voice-port 3/0/0
    !
    voice-port 3/0/1
    !
    voice-port 3/1/0
    !
    voice-port 3/1/1
    !
    dial-peer cor custom
    !
    dial-peer voice 9 pots
    destination-pattern 1111
    port 3/1/1
    !
    dial-peer voice 10 pots
    destination-pattern 1112
    port 3/1/0
    !
    dial-peer voice 7 pots
    destination-pattern 7...
    direct-inward-dial
    prefix 7
    !
    !
    gatekeeper
    shutdown
    !
    !
    line con 0
    line aux 0
    line vty 0 4
    password kyz3
    login
    !
    !
    end
     
    richardp, Jan 5, 2004
    #1
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.