Hi I have a CISCO 1841 router with a ADSL WIC in it. I decided to add a CISCO SDSL WIC in it. But I am unable to configure it from the IOS software as I cannot see it Can any one point me in the right direction here are the output from sh ver and sh diag Clearly the diag can see it, but when I do show interface it does not show up, it only shows the ADSL interface ++++++++++++++++++++++++++++++++++++++++++++++++++++++ show diag Slot 0: C1841 2FE 2SLOT Mainboard Port adapter, 4 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Chassis MAC Address : 001d.71d7.ed64 MAC Address block size : 34 PCB Serial Number : FOC11364UZD Hardware Revision : 7.0 Part Number : 73-8191-08 Board Revision : C0 Top Assy. Part Number : 800-23434-06 Deviation Number : 0 Fab Version : 04 CLEI Code : IPM7W00CRA RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : CISCO1841 Version Identifier : V05 Processor type : 86 Chassis Serial Number : FCZ114091K5 EEPROM format version 4 EEPROM contents (hex): ... WIC/HWIC Slot 0: GSI GSHDSL MULTI LINE ATM WIC Hardware Revision : 0.0 Top Assy. Part Number : 800-26571-02 Board Revision : C0 Deviation Number : 0 Fab Version : 01 PCB Serial Number : FOC11473840 RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Version Identifier : V02 Product (FRU) Number : WIC-1SHDSL-V3 EEPROM format version 4 WIC/HWIC Slot 1: DSL SAR (ADSL) Hardware Revision : 2.3 Part Number : 73-4771-09 Board Revision : C0 Deviation Number : 0-0 Fab Version : 05 PCB Serial Number : FOC11355HRC RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : WIC-1ADSL= EEPROM format version 4 .... ++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++++++++++++++++++++++++++++++++++++++++++++++ show ver Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(16a), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Mon 10-Sep-07 07:24 by prod_rel_team ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) yourname uptime is 32 minutes System returned to ROM by power-on System image file is "flash:c1841-broadband-mz.124-16a.bin" Cisco 1841 (revision 7.0) with 113664K/17408K bytes of memory. Processor board ID FCZ114091K5 1 DSL controller 2 FastEthernet interfaces 1 ATM interface DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 31360K bytes of ATA CompactFlash (Read/Write) Configuration register is 0x2102 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
conf t controller dsl 0/0 line-term cpe mode atm line-mode ... ..... Looks like you have a DSL controller. You should be all set. After you do your controller dsl 0/0 commands, you should have an ATM 0/0 interface. http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123newft/123t/123t_7/gt4wire.htm