Change E1 card to T1 card possible on AS5350?

Discussion in 'Cisco' started by Vorta, May 5, 2005.

  1. Vorta

    Vorta Guest

    Hello all:

    I have an AS5350, with two E1/PRI Ports:

    cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of
    memory.
    Processor board ID JAE07170MY3
    R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3
    Cache
    Last reset from power-on
    Channelized E1, Version 1.0.
    Bridging software.
    X.25 software, Version 3.0.0.
    SuperLAT software (copyright 1990 by Meridian Technology Corp).
    Primary Rate ISDN software, Version 1.1.
    Manufacture Cookie Info:
    EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
    Board Hardware Version 3.34, Item Number 800-5171-02,
    Board Revision C0, Serial Number JAE07170MY3,
    PLD/ISP Version 2.2, Manufacture Date 25-Apr-2003.
    Processor 0x14, MAC Address 0x0C30821B7A
    Backplane HW Revision 1.0, Flash Type 5V
    2 FastEthernet/IEEE 802.3 interface(s)
    2 Serial network interface(s)
    60 terminal line(s)

    2 Channelized E1/PRI port(s)

    512K bytes of non-volatile configuration memory.
    32768K bytes of processor board System flash (Read/Write)
    8192K bytes of processor board Boot flash (Read/Write)

    Is it possible to some how flash the firmwares on those E1 ports
    and make them T1/PRI port?

    Thank you,

    John
     
    Vorta, May 5, 2005
    #1
    1. Advertisements

  2. The DFC trunk cards are not field switchable between
    E1 and T1, sorry.

    Aaron

    ---

    ~
    ~ I have an AS5350, with two E1/PRI Ports:
    ~
    ~ cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of
    ~ memory.
    ~ Processor board ID JAE07170MY3
    ~ R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3
    ~ Cache
    ~ Last reset from power-on
    ~ Channelized E1, Version 1.0.
    ~ Bridging software.
    ~ X.25 software, Version 3.0.0.
    ~ SuperLAT software (copyright 1990 by Meridian Technology Corp).
    ~ Primary Rate ISDN software, Version 1.1.
    ~ Manufacture Cookie Info:
    ~ EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
    ~ Board Hardware Version 3.34, Item Number 800-5171-02,
    ~ Board Revision C0, Serial Number JAE07170MY3,
    ~ PLD/ISP Version 2.2, Manufacture Date 25-Apr-2003.
    ~ Processor 0x14, MAC Address 0x0C30821B7A
    ~ Backplane HW Revision 1.0, Flash Type 5V
    ~ 2 FastEthernet/IEEE 802.3 interface(s)
    ~ 2 Serial network interface(s)
    ~ 60 terminal line(s)
    ~
    ~ 2 Channelized E1/PRI port(s)
    ~
    ~ 512K bytes of non-volatile configuration memory.
    ~ 32768K bytes of processor board System flash (Read/Write)
    ~ 8192K bytes of processor board Boot flash (Read/Write)
    ~
    ~ Is it possible to some how flash the firmwares on those E1 ports
    ~ and make them T1/PRI port?
    ~
    ~ Thank you,
    ~
    ~ John
     
    Aaron Leonard, May 5, 2005
    #2
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.