CallForward outside->inside->outside failed after one ring.

Hi everybody,

I'm using a full Cisco hardware solution for my ToIP.
Cisco IP (mostly 7911) phone and a CCME 2821.

Everything is working just good except when I have a callfowradAll on
a phone.
Let me explaine my probleme :

I have a "Phone A" with the DID number xxxxxxxxxx and a CallForwardAll
on this Phone to an other DID number yyyyyyyyyy
The internal "Phone A" number is zzz

If i'm on any other company's phone and that I call the "Phone A" to
zzz I will be tranferd to yyyyyyyyyy.
It work just fine.

If I call the "Phone A" from the outside on xxxxxxxxxx the outside
phone with the number yyyyyyyyyy will ring just once and the tranfert
will failed...

All "automatics" transfert outside->inside->outside will failed.
All "automatics" transfert inside->inside->outside succed
All "automatics" transfert inside->inside->inside succed
All "manually" transfer works all the time...

I really need some helep..
I have the q931 debug output :
Im callin from 827750706(outside) to 261387471 (DID number phone my
phone 7471)
The 7471 ligne forward all to 2645615542(outside)

Here is the debug:
002748: Apr 12 10:25:46.079: %LINK-3-UPDOWN: Interface BRI0/0/1,
changed state to up
002749: Apr 12 10:25:46.259: ISDN BR0/0/1 Q931: RX <- SETUP pd = 8
callref = 0x3F
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Exclusive, B1
Calling Party Number i = 0x2083, '827750706'
Plan:Unknown, Type:National
Called Party Number i = 0x81, '7471'
Plan:ISDN, Type:Unknown
High Layer Compat i = 0x9181
Sending Complete
002750: Apr 12 10:25:46.283: ISDN BR0/0/0 Q931: Applying typeplan for
sw-type 0x1 is 0
x2 0x0, Calling num 141387496
002751: Apr 12 10:25:46.283: ISDN BR0/0/0 Q931: Applying typeplan for
sw-type 0x1 is 0
x0 0x0, Called num 0145615542
002752: Apr 12 10:25:46.283: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8
callref = 0x6B
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x82
Preferred, B2
Calling Party Number i = 0x2083, '261387471'
Plan:Unknown, Type:National
Called Party Number i = 0x80, '2645615542'
Plan:Unknown, Type:Unknown
High Layer Compat i = 0x9181
Sending Complete
002753: Apr 12 10:25:46.287: %ISDN-6-LAYER2UP: Layer 2 for Interface
BR0/0/1, TEI 64 c
hanged to up
002754: Apr 12 10:25:46.291: ISDN BR0/0/1 Q931: TX -> CALL_PROC pd =
8 callref = 0xBF

Channel ID i = 0x89
Exclusive, B1
002755: Apr 12 10:25:46.531: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd =
8 callref = 0xEB

Channel ID i = 0x8A
Exclusive, B2
002756: Apr 12 10:25:47.687: ISDN BR0/0/0 Q931: RX <- PROGRESS pd = 8
callref = 0xEB
Cause i = 0x87F2 - Unknown cause value
Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band
info
002757: Apr 12 10:25:47.691: ISDN BR0/0/1 Q931: TX -> PROGRESS pd = 8
callref = 0xBF
Cause i = 0x87F2 - Unknown cause value
Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band
info
002758: Apr 12 10:25:47.755: ISDN BR0/0/1 Q931: RX <- RELEASE_COMP pd
= 8 callref = 0
x3F
Cause i = 0x87E2 - Message not compatible with call state or not
implemented
002759: Apr 12 10:25:47.771: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd =
8 callref = 0x6
B
Cause i = 0x80E2 - Message not compatible with call state or not
implemented
002760: Apr 12 10:25:47.939: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8
callref = 0xEB
002761: Apr 12 10:25:47.943: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd
= 8 callref = 0
x6B
002762: Apr 12 10:25:51.655: %ISDN-6-LAYER2DOWN: Layer 2 for Interface
BR0/0/1, TEI 64
changed to down
002763: Apr 12 10:25:51.655: ISDN BR0/0/1 Q931: Ux_DLRelInd:
DL_REL_IND received from
L2
CCME-01#


All DID number are good and isdn type and plan are good too...


If you have any idea, I will really apprecite.
Thanks,
Nicolas

 

nobody ?