AIM-ATM

Hi,
I have a 3745 with (C3745-IPBASE-M), Version 12.3(5b) IOS.
In slot 1 there is a NM-2W Port adapter with two AIM-ATM modules (4 E1
ports).
I'd like to configure AIM for ATM WAN Access with IMA (Inverse Multiplexing)
but it seems that router doesn't see interfaces.
This is the output of 'sh ver':
#################################################
Cisco Internetwork Operating System Software
IOS (tm) 3700 Software (C3745-IPBASE-M), Version 12.3(5b), RELEASE SOFTWARE
(fc1
)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Thu 15-Jan-04 23:39 by kellythw
Image text-base: 0x60008AF4, data-base: 0x6102E000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

Router uptime is 10 minutes
System returned to ROM by power-on
System image file is "flash:c3745-ipbase-mz.123-5b.bin"

cisco 3745 (R7000) processor (revision 2.0) with 118784K/12288K bytes of
memory.
Processor board ID JHY0814K05R
R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2, 2048KB L3 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
4 Channelized E1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
151K bytes of non-volatile configuration memory.
31360K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102
##############################################

and this is the relevant part of 'sh diag':

##############################################
Slot 1:
NM-2W Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
....
WIC Slot 0:
E1 (2 port) WAN daughter card
Hardware revision 1.0 Board revision D0
Serial number 31750923 Part number 800-04479-03
Test history 0x0 RMA number 00-00-00
Connector type PCI
....
WIC Slot 1:
E1 (2 port) WAN daughter card
Hardware revision 1.0 Board revision D0
Serial number 31750989 Part number 800-04479-03
Test history 0x0 RMA number 00-00-00
Connector type PCI
################################################à

For instance, I'm unable to give these commands:
conf t
controller e1 1/0
mode atm aim 0
??????

How can I see atm interfaces?
Any help?

Thanks in advance
Mimmus

 

Have not looked myself but check to make sure that that feature is available
in that IOS, Looks like you have the basic ISO, my need a feature set like
IP PLUS, Not sure how the new IOS trains are with the new sheme. Should be
able to use software advisor on Cisco's site.

 

No, I tried with latest IOS with IP-PLUS:

#####################################################à
Cisco Internetwork Operating System Software
IOS (tm) 3700 Software (C3745-IS-M), Version 12.3(9), RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 14-May-04 12:54 by dchih
Image text-base: 0x60008AF4, data-base: 0x61C00000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
ROM: 3700 Software (C3745-IPBASE-M), Version 12.3(5b), RELEASE SOFTWARE
(fc1)

Router uptime is 11 minutes
System returned to ROM by reload
System image file is "flash:c3745-is-mz.123-9.bin"

cisco 3745 (R7000) processor (revision 2.0) with 118784K/12288K bytes of
memory.
Processor board ID JHY0814K05R
R7000 CPU at 350MHz, Implementation 39, Rev 3.3, 256KB L2, 2048KB L3 Cache
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
4 Channelized E1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
151K bytes of non-volatile configuration memory.
31360K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

###################################################

but I'm still unable to set controller in ATM mode.

Other ideas?

Thanks again
Mimmus

 

You may need to upgrade the firmware on the card. I need to upgrade
the firmware on my card. the card is booting with a firmware error
message "WARNING: ATM Board firmware is at level 12", " ATM: Firmware
revision must be 14 or higher", "KAS(9): Event: Link up in LANE mode"
Do you think I can get the firmware upgrade off the Cisco web site??
Where can I get the firmware??

 

I have no idea.
I have no message at boot.

Mimmus