VPN Connection Problems between Cisco PIX 506E and Cisco VPN Concentrator 3005

Discussion in 'Cisco' started by Kai, Feb 15, 2005.

  1. Kai

    Kai Guest

    Hello all,

    I got a problem with a vpn connection from a cisco pix 506E to a cisco
    3005 concentrator. The problem is that the lan on the pix is also used
    to another remote side. so I tried to activate NAT on the pix to
    translate the ip adresses of the network. after that I entered the
    information at the concentrator which are nessassray for the
    lan-to-lan connection.
    But I did not get a connection. I tried to ping the outside address of
    the pix but I did not get a reply.

    I post the output of the logfile for that connection below:



    29437 02/15/2005 14:25:21.890 SEV=4 IKE/41 RPT=43758 213.183.66.179
    IKE Initiator: New Phase 1, Intf 2, IKE Peer 213.183.66.179
    local Proxy Address 192.168.0.0, remote Proxy Address 213.183.66.179,
    SA (L2L: to PIX)

    29507 02/15/2005 14:26:02.300 SEV=4 IKEDBG/65 RPT=36896 213.183.66.179
    Group [213.183.66.179]
    IKE MM Initiator FSM error history (struct &0x3b7510c)
    <state>, <event>:
    MM_DONE, EV_ERROR
    MM_WAIT_MSG6, EV_TIMEOUT
    MM_WAIT_MSG6, NullEvent
    MM_SND_MSG5, EV_SND_MSG



    and here is the config of the pix:

    PIX Version 6.3(4)
    interface ethernet0 auto
    interface ethernet1 auto
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password 8Ry2YjIyt7RRXU24 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    hostname Cisco-Firewall-VPN
    domain-name pk-intern.de
    clock timezone CEST 1
    clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    access-list ipsec permit ip host 2xx.1xx.6x.1xx 192.168.8.224
    255.255.255.224
    access-list ipsec permit ip 192.168.41.0 255.255.255.0 192.168.4.0
    255.255.255.0

    access-list ipsec permit ip 192.168.41.0 255.255.255.0 192.168.8.224
    255.255.255
    ..224
    access-list nonat permit ip any host 192.168.14.1
    access-list nonat permit ip any 192.168.14.0 255.255.255.192
    access-list nonat permit ip host 2xx.1xx.6x.1xx 192.168.8.xxx
    255.255.255.224
    access-list nonat permit ip 192.168.4.0 255.255.255.0 192.168.8.xxx
    255.255.255.
    224
    access-list outside_cryptomap_dyn_20 permit ip any host 192.168.14.1
    access-list outside_cryptomap_dyn_20 permit ip any 192.168.14.0
    255.255.255.192
    access-list outside_cryptomap_30 permit ip 192.168.4.0 255.255.255.0
    192.168.8.xxx 255.255.255.224
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    ip address outside 2xx.1xx.6x.1xx 255.255.255.248
    ip address inside 192.168.4.xx 255.255.255.0
    ip audit info action alarm
    ip audit attack action alarm
    ip local pool EDV 192.168.14.1-192.168.14.32 mask 255.255.255.0
    pdm location 192.168.4.xx 255.255.255.255 inside
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 2xx.1xx.6x.1xx
    nat (inside) 0 access-list nonat
    static (inside,outside) 192.168.41.0 192.168.4.0 netmask 255.255.255.0
    0 0
    route outside 0.0.0.0 0.0.0.0 2xx.1xx.6x.1xx 1
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225
    1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server TACACS+ max-failed-attempts 3
    aaa-server TACACS+ deadtime 10
    aaa-server RADIUS protocol radius
    aaa-server RADIUS max-failed-attempts 3
    aaa-server RADIUS deadtime 10
    aaa-server LOCAL protocol local
    http server enable
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    sysopt connection permit-ipsec
    crypto ipsec transform-set set-3des esp-3des esp-md5-hmac
    crypto dynamic-map outside_dyn_map 20 match address
    outside_cryptomap_dyn_20
    crypto dynamic-map outside_dyn_map 20 set transform-set set-3des
    crypto map vpn 10 ipsec-isakmp
    crypto map vpn 10 match address ipsec
    crypto map vpn 10 set peer 2xx.1xx.1xx.9x
    crypto map vpn 10 set transform-set set-3des
    crypto map vpn 30 ipsec-isakmp
    crypto map vpn 30 match address outside_cryptomap_30
    crypto map vpn 30 set peer 2xx.1xx.1xx.9x
    crypto map vpn 30 set transform-set set-3des
    crypto map vpn 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map vpn client authentication LOCAL
    crypto map vpn interface outside
    isakmp enable outside
    isakmp key ******** address 2xx.1xx.1xx.9x netmask 255.255.255.255
    no-xauth no-c
    onfig-mode
    isakmp identity address
    isakmp policy 10 authentication pre-share
    isakmp policy 10 encryption 3des
    isakmp policy 10 hash md5
    isakmp policy 10 group 2
    isakmp policy 10 lifetime 3600
    vpngroup EDV address-pool EDV
    vpngroup EDV dns-server 192.168.4.xxx 192.168.2.xxx
    vpngroup EDV wins-server 192.168.4.xxx 192.168.2.xxx
    vpngroup EDV default-domain pk-intern.de
    vpngroup EDV idle-time 1800
    vpngroup EDV password ********
    telnet 192.168.4.x 255.255.255.0 inside
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd dns 192.168.4.xxx
    dhcpd lease 3600
    dhcpd ping_timeout 750
    dhcpd domain pk-intern.de
    username user password mrbAHCmBQ56It1RP encrypted privilege 15
    vpnclient server 2xx.1xx.6x.1xx
    vpnclient mode client-mode
    vpnclient vpngroup user password ********
    vpnclient username user password ********
    terminal width 80
    Cryptochecksum:f18163247c8b2ebfc2cf0a40e3e71ff8
    : end
    Kai, Feb 15, 2005
    #1
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Kai
    Replies:
    1
    Views:
    834
    Walter Roberson
    May 14, 2004
  2. Replies:
    0
    Views:
    468
  3. Replies:
    4
    Views:
    2,004
    Scott Lowe
    Jun 26, 2005
  4. Scott
    Replies:
    1
    Views:
    2,594
  5. ruraldev
    Replies:
    0
    Views:
    555
    ruraldev
    Mar 1, 2007
Loading...

Share This Page