Slow Internet file download using Cisco Router 1710 + PCI broadband router

Discussion in 'Cisco' started by Sam, Dec 27, 2003.

  1. Sam

    Sam Guest

    I brought a new Cisco router 1710 and used it with a PCI broadband
    router for Internet access. The file download speed from Internet is
    really slow. When I replace the Cisco router with another broadband
    router, it is much better.

    Workstation 10.10.20.2 configs:
    1. ip address: 10.10.20.2 netmask 255.255.255.0
    2. default gateway: 10.10.20.1

    Cisco router 1710 major configs:
    1. ip route 0.0.0.0 0.0.0.0 192.168.0.3
    2. interface Fast Ethernet 0: ip address 10.10.20.1 255.255.255.0
    ip nat inside
    3. interface Ethernet 0: ip address 192.168.0.7 255.255.0.0
    ip nat outside
    4. access-list 7 permit 10.10.20.0 0.0.0.255
    ip nat inside source list 7 interface Ethernet 0 overload

    PCI broadband router major configs:
    1. interface LAN: ip address 192.168.0.3
    2. interface WAN: ip address xxx.xxx.xxx.xxx (ISP assigned)
    3. NAT: enabled

    Thank you in advance
    Regards
     
    Sam, Dec 27, 2003
    #1
    1. Advertising

  2. Sam

    Rik Bain Guest

    On Fri, 26 Dec 2003 21:00:53 -0600, Sam wrote:

    > I brought a new Cisco router 1710 and used it with a PCI broadband
    > router for Internet access. The file download speed from Internet is
    > really slow. When I replace the Cisco router with another broadband
    > router, it is much better.
    >
    > Workstation 10.10.20.2 configs:
    > 1. ip address: 10.10.20.2 netmask 255.255.255.0 2. default gateway:
    > 10.10.20.1
    >
    > Cisco router 1710 major configs:
    > 1. ip route 0.0.0.0 0.0.0.0 192.168.0.3 2. interface Fast Ethernet 0: ip
    > address 10.10.20.1 255.255.255.0
    > ip nat inside
    > 3. interface Ethernet 0: ip address 192.168.0.7 255.255.0.0
    > ip nat outside
    > 4. access-list 7 permit 10.10.20.0 0.0.0.255
    > ip nat inside source list 7 interface Ethernet 0 overload
    >
    > PCI broadband router major configs:
    > 1. interface LAN: ip address 192.168.0.3 2. interface WAN: ip address
    > xxx.xxx.xxx.xxx (ISP assigned) 3. NAT: enabled
    >
    > Thank you in advance
    > Regards



    First thing /I/ would do is check "show interface" output for errors.
     
    Rik Bain, Dec 27, 2003
    #2
    1. Advertising

  3. Sam

    PES Guest

    Are you using pppoe. If so, try "ip tcp adjust-mss 1452" on the interface
    that connects to the internet.

    "Sam" <> wrote in message
    news:...
    > I brought a new Cisco router 1710 and used it with a PCI broadband
    > router for Internet access. The file download speed from Internet is
    > really slow. When I replace the Cisco router with another broadband
    > router, it is much better.
    >
    > Workstation 10.10.20.2 configs:
    > 1. ip address: 10.10.20.2 netmask 255.255.255.0
    > 2. default gateway: 10.10.20.1
    >
    > Cisco router 1710 major configs:
    > 1. ip route 0.0.0.0 0.0.0.0 192.168.0.3
    > 2. interface Fast Ethernet 0: ip address 10.10.20.1 255.255.255.0
    > ip nat inside
    > 3. interface Ethernet 0: ip address 192.168.0.7 255.255.0.0
    > ip nat outside
    > 4. access-list 7 permit 10.10.20.0 0.0.0.255
    > ip nat inside source list 7 interface Ethernet 0 overload
    >
    > PCI broadband router major configs:
    > 1. interface LAN: ip address 192.168.0.3
    > 2. interface WAN: ip address xxx.xxx.xxx.xxx (ISP assigned)
    > 3. NAT: enabled
    >
    > Thank you in advance
    > Regards
     
    PES, Dec 27, 2003
    #3
  4. Sam

    Sam Guest

    Hi PES,

    Thank you for your help. I am not using PPPoE. The ISP assigns fixed
    IP to my broadband connection. The network diagram looks like:

    10.10.2.0/24 <-> Cisco 1710 <-> 192.168.0.0/16 <-> PCI broadband
    router <-> Internet

    Regards

    "PES" <NO*SPAMpestewartREMOVE**SUCKS> wrote in message news:<3fecfd7c$>...
    > Are you using pppoe. If so, try "ip tcp adjust-mss 1452" on the interface
    > that connects to the internet.
    >
    > "Sam" <> wrote in message
    > news:...
    > > I brought a new Cisco router 1710 and used it with a PCI broadband
    > > router for Internet access. The file download speed from Internet is
    > > really slow. When I replace the Cisco router with another broadband
    > > router, it is much better.
    > >
    > > Workstation 10.10.20.2 configs:
    > > 1. ip address: 10.10.20.2 netmask 255.255.255.0
    > > 2. default gateway: 10.10.20.1
    > >
    > > Cisco router 1710 major configs:
    > > 1. ip route 0.0.0.0 0.0.0.0 192.168.0.3
    > > 2. interface Fast Ethernet 0: ip address 10.10.20.1 255.255.255.0
    > > ip nat inside
    > > 3. interface Ethernet 0: ip address 192.168.0.7 255.255.0.0
    > > ip nat outside> > Thank you in advance
    > > Regards
    > > 4. access-list 7 permit 10.10.20.0 0.0.0.255
    > > ip nat inside source list 7 interface Ethernet 0 overload
    > >
    > > PCI broadband router major configs:
    > > 1. interface LAN: ip address 192.168.0.3
    > > 2. interface WAN: ip address xxx.xxx.xxx.xxx (ISP assigned)
    > > 3. NAT: enabled
    > >
     
    Sam, Dec 27, 2003
    #4
  5. Sam

    Sam Guest

    Hi Rik,

    Q1. Thank you for your help. Here are the results. Is it normal to
    have so many broadcasts received on Ethernet interface within 30 secs?

    samsrt#sh int e0
    Ethernet0 is up, line protocol is up
    Hardware is PQUICC Ethernet, address is 0005.9a3c.f923 (bia
    0005.9a3c.f923)
    Internet address is 192.168.0.7/16
    MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    reliability 255/255, txload 1/255, rxload 5/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 10BaseT
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:00:00, output 00:00:04, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 212000 bits/sec, 4 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    999903 packets input, 366262858 bytes, 0 no buffer
    Received 815018 broadcasts, 0 runts, 2 giants, 0 throttles
    19270 input errors, 19268 CRC, 0 frame, 0 overrun, 0 ignored
    0 input packets with dribble condition detected
    693690 packets output, 72720727 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    samsrt#sh int f0
    FastEthernet0 is up, line protocol is up
    Hardware is PQUICC_FEC, address is 0005.9a3c.f922 (bia
    0005.9a3c.f922)
    Internet address is 10.10.20.1/24
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 100Mb/s, 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:04:00, output 00:00:06, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 1 drops
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    657149 packets input, 68749515 bytes
    Received 5317 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog
    0 input packets with dribble condition detected
    226486 packets output, 268732760 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    ***************** After 30 secs ***********************

    samsrt# sh int e0
    Ethernet0 is up, line protocol is up
    Hardware is PQUICC Ethernet, address is 0005.9a3c.f923 (bia
    0005.9a3c.f923)
    Internet address is 192.168.0.7/16
    MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    reliability 255/255, txload 1/255, rxload 4/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 10BaseT
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:00:01, output 00:00:09, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 0 drops
    5 minute input rate 189000 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    999925 packets input, 366265202 bytes, 0 no buffer
    Received 815040 broadcasts, 0 runts, 2 giants, 0 throttles
    19270 input errors, 19268 CRC, 0 frame, 0 overrun, 0 ignored
    0 input packets with dribble condition detected
    693692 packets output, 72720847 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out

    samsrt#sh int f0
    FastEthernet0 is up, line protocol is up
    Hardware is PQUICC_FEC, address is 0005.9a3c.f922 (bia
    0005.9a3c.f922)
    Internet address is 10.10.20.1/24
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    Keepalive set (10 sec)
    Full-duplex, 100Mb/s, 100BaseTX/FX
    ARP type: ARPA, ARP Timeout 04:00:00
    Last input 00:04:18, output 00:00:02, output hang never
    Last clearing of "show interface" counters never
    Queueing strategy: fifo
    Output queue 0/40, 0 drops; input queue 0/75, 1 drops
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    657149 packets input, 68749515 bytes
    Received 5317 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog
    0 input packets with dribble condition detected
    226489 packets output, 268733302 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out


    Q2. There are many strange accesses from 192.168.0.0/16 like this. Is
    it caused by worm or virus on the network?

    4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.40(138) ->
    192.168.255.255(138),
    1 packet
    4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.1(138) ->
    192.168.255.255(138),
    1 packet
    4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(138) ->
    192.168.255.255(138),
    1 packet
    4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.29(138) ->
    192.168.255.255(138),
    1 packet
    4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(137) ->
    192.168.255.255(137),
    1 packet

    Thank you
    Regards
    Sam



    Rik Bain <> wrote in message news:<>...
    > On Fri, 26 Dec 2003 21:00:53 -0600, Sam wrote:
    >
    > > I brought a new Cisco router 1710 and used it with a PCI broadband
    > > router for Internet access. The file download speed from Internet is
    > > really slow. When I replace the Cisco router with another broadband
    > > router, it is much better.
    > >
    > > Workstation 10.10.20.2 configs:
    > > 1. ip address: 10.10.20.2 netmask 255.255.255.0 2. default gateway:
    > > 10.10.20.1
    > >
    > > Cisco router 1710 major configs:
    > > 1. ip route 0.0.0.0 0.0.0.0 192.168.0.3 2. interface Fast Ethernet 0: ip
    > > address 10.10.20.1 255.255.255.0
    > > ip nat inside
    > > 3. interface Ethernet 0: ip address 192.168.0.7 255.255.0.0
    > > ip nat outside
    > > 4. access-list 7 permit 10.10.20.0 0.0.0.255
    > > ip nat inside source list 7 interface Ethernet 0 overload
    > >
    > > PCI broadband router major configs:
    > > 1. interface LAN: ip address 192.168.0.3 2. interface WAN: ip address
    > > xxx.xxx.xxx.xxx (ISP assigned) 3. NAT: enabled
    > >
    > > Thank you in advance
    > > Regards

    >
    >
    > First thing /I/ would do is check "show interface" output for errors.
     
    Sam, Dec 27, 2003
    #5
  6. Sam

    Rik Bain Guest

    On Sat, 27 Dec 2003 06:52:06 -0600, Sam wrote:


    inline

    > Hi Rik,
    >
    > Q1. Thank you for your help. Here are the results. Is it normal to have
    > so many broadcasts received on Ethernet interface within 30 secs?
    >


    i wouldnt worry about that.

    > ***************** After 30 secs ***********************
    >
    > samsrt# sh int e0
    > Ethernet0 is up, line protocol is up
    > Hardware is PQUICC Ethernet, address is 0005.9a3c.f923 (bia
    > 0005.9a3c.f923)
    > Internet address is 192.168.0.7/16
    > MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    > reliability 255/255, txload 1/255, rxload 4/255
    > Encapsulation ARPA, loopback not set
    > Keepalive set (10 sec)
    > Full-duplex, 10BaseT
    > ARP type: ARPA, ARP Timeout 04:00:00
    > Last input 00:00:01, output 00:00:09, output hang never Last clearing
    > of "show interface" counters never Queueing strategy: fifo Output
    > queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate
    > 189000 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0
    > packets/sec
    > 999925 packets input, 366265202 bytes, 0 no buffer Received 815040
    > broadcasts, 0 runts, 2 giants, 0 throttles 19270 input errors,
    > 19268 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with
    > dribble condition detected 693692 packets output, 72720847 bytes, 0
    > underruns 0 output errors, 0 collisions, 2 interface resets 0
    > babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier
    > 0 output buffer failures, 0 output buffers swapped out
    >
    >


    I would be willing to bet that "19270 input errors,
    19268 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with" is
    your performance problem. check speed/duplex or any other ethernet
    troubleshooting steps that you employ.



    >
    > Q2. There are many strange accesses from 192.168.0.0/16 like this. Is it
    > caused by worm or virus on the network?
    >


    depends on frequency, you could enable timestamps to determine. but most
    likely, it is regular windows traffic, since the other router doesnt
    suffer performance related issues.


    > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.40(138) ->
    > 192.168.255.255(138),
    > 1 packet
    > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.1(138) ->
    > 192.168.255.255(138),
    > 1 packet
    > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(138) ->
    > 192.168.255.255(138),
    > 1 packet
    > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.29(138) ->
    > 192.168.255.255(138),
    > 1 packet
    > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(137) ->
    > 192.168.255.255(137),
    > 1 packet
    >
    > Thank you
    > Regards
    > Sam
    >
    >
     
    Rik Bain, Dec 27, 2003
    #6
  7. Sam

    Sam Guest

    Dear Rik,

    Thank you for you help.
    Would you please explain more on troubleshooting CRC errors and
    speed/duplex? Do I need to match the speed/duplex between router
    interface and switch port, or between the two router interfaces? Sorry
    for I am a beginner in networking.

    Thank you in advance
    Regards
    Sam


    Rik Bain <> wrote in message news:<>...
    > On Sat, 27 Dec 2003 06:52:06 -0600, Sam wrote:
    >
    >
    > inline
    >
    > > Hi Rik,
    > >
    > > Q1. Thank you for your help. Here are the results. Is it normal to have
    > > so many broadcasts received on Ethernet interface within 30 secs?
    > >

    >
    > i wouldnt worry about that.
    >
    > > ***************** After 30 secs ***********************
    > >
    > > samsrt# sh int e0
    > > Ethernet0 is up, line protocol is up
    > > Hardware is PQUICC Ethernet, address is 0005.9a3c.f923 (bia
    > > 0005.9a3c.f923)
    > > Internet address is 192.168.0.7/16
    > > MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
    > > reliability 255/255, txload 1/255, rxload 4/255
    > > Encapsulation ARPA, loopback not set
    > > Keepalive set (10 sec)
    > > Full-duplex, 10BaseT
    > > ARP type: ARPA, ARP Timeout 04:00:00
    > > Last input 00:00:01, output 00:00:09, output hang never Last clearing
    > > of "show interface" counters never Queueing strategy: fifo Output
    > > queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate
    > > 189000 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0
    > > packets/sec
    > > 999925 packets input, 366265202 bytes, 0 no buffer Received 815040
    > > broadcasts, 0 runts, 2 giants, 0 throttles 19270 input errors,
    > > 19268 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with
    > > dribble condition detected 693692 packets output, 72720847 bytes, 0
    > > underruns 0 output errors, 0 collisions, 2 interface resets 0
    > > babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier
    > > 0 output buffer failures, 0 output buffers swapped out
    > >
    > >

    >
    > I would be willing to bet that "19270 input errors,
    > 19268 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with" is
    > your performance problem. check speed/duplex or any other ethernet
    > troubleshooting steps that you employ.
    >
    >
    >
    > >
    > > Q2. There are many strange accesses from 192.168.0.0/16 like this. Is it
    > > caused by worm or virus on the network?
    > >

    >
    > depends on frequency, you could enable timestamps to determine. but most
    > likely, it is regular windows traffic, since the other router doesnt
    > suffer performance related issues.
    >
    >
    > > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.40(138) ->
    > > 192.168.255.255(138),
    > > 1 packet
    > > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.1(138) ->
    > > 192.168.255.255(138),
    > > 1 packet
    > > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(138) ->
    > > 192.168.255.255(138),
    > > 1 packet
    > > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.29(138) ->
    > > 192.168.255.255(138),
    > > 1 packet
    > > 4d03h: %SEC-6-IPACCESSLOGP: list 101 denied udp 192.168.3.89(137) ->
    > > 192.168.255.255(137),
    > > 1 packet
    > >
    > > Thank you
    > > Regards
    > > Sam
    > >
    > >
     
    Sam, Dec 29, 2003
    #7
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Ole Vik
    Replies:
    0
    Views:
    1,633
    Ole Vik
    Jul 8, 2003
  2. Arben Qarkaxhija

    Newbe question Cisco 1710 router!

    Arben Qarkaxhija, Jul 18, 2003, in forum: Cisco
    Replies:
    3
    Views:
    3,631
    Jeff Specoli
    Jul 18, 2003
  3. news.connect.com.au
    Replies:
    0
    Views:
    844
    news.connect.com.au
    Nov 25, 2003
  4. Paul Stewart

    VPN Problems 1710 to 1710 via ADSL

    Paul Stewart, Dec 5, 2003, in forum: Cisco
    Replies:
    1
    Views:
    4,159
    Phillip Remaker
    Dec 5, 2003
  5. S-Mac

    1710 for Broadband access.

    S-Mac, Dec 28, 2004, in forum: Cisco
    Replies:
    17
    Views:
    769
    S Mac
    Jan 7, 2005
Loading...

Share This Page