RSM 5500

Discussion in 'Cisco' started by adamp@os.pl, Jul 28, 2007.

  1. Guest

    Hello,
    I am trying configure communication beteewn vlan on catalyst 5500
    with RSM WS-X5302 but I cant find command ip routing and router. What
    can I do to !

    interface Vlan11
    description xxx
    ip address 89.9.64.65 255.255.255.192
    no ip route-cache
    !
    interface Vlan12
    description xxx
    ip address 89.9.64.129 255.255.255.192
    no ip route-cache

    Please help me.
    , Jul 28, 2007
    #1
    1. Advertising

  2. writes:
    >Hello,
    > I am trying configure communication beteewn vlan on catalyst 5500
    >with RSM WS-X5302 but I cant find command ip routing and router. What
    >can I do to !


    >interface Vlan11
    > description xxx
    > ip address 89.9.64.65 255.255.255.192
    > no ip route-cache
    >!
    >interface Vlan12
    > description xxx
    > ip address 89.9.64.129 255.255.255.192
    > no ip route-cache


    >Please help me.



    The RSM is a seperate console.

    You configure switching on the Sup. You then access the RSM console
    with the session command (or over its console port) and configure
    routing on the RSM console.

    http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/cnfg_nts/rsm/4058_01.htm

    Your commands above look like l2 switching commands entered in the sup only.

    Cisco never did a native combined together IOS for the 5500, that only
    went into the 6500 for certain setups, or the 4500 SupIV and up.
    Doug McIntyre, Jul 28, 2007
    #2
    1. Advertising

  3. In article <46ab70a3$0$79254$>,
    Doug McIntyre <> wrote:
    > writes:
    >> I am trying configure communication beteewn vlan on catalyst 5500
    >>with RSM WS-X5302 but I cant find command ip routing and router.


    >>interface Vlan11
    >> description xxx
    >> ip address 89.9.64.65 255.255.255.192
    >> no ip route-cache


    >>interface Vlan12
    >> description xxx
    >> ip address 89.9.64.129 255.255.255.192
    >> no ip route-cache



    >You configure switching on the Sup. You then access the RSM console
    >with the session command (or over its console port) and configure
    >routing on the RSM console.


    >Your commands above look like l2 switching commands entered in the sup only.


    I have to disagree; the Cat 5000 Supervisor did not allow you
    to configure per-interface IP addresses or to configure route caching.
    The commands shown are obviously commands from the IOS side, living
    on the RSM. The Supervisor side uses command such as "set vlan"
    to define which ports are in which VLAN, but doesn't allow you to
    configure how to talk between the VLANs.


    The original posting is not entirely specific about where those
    particular commands are from, not specific about whether they
    are what the OP would -like- to put in, or what the OP already has.
    If they are what the OP would -like- to put in, then your advice
    to use the 'session' command is probably the solution; if
    the OP pulled the commands shown off of the RSM already then
    there is some other issue.
    Walter Roberson, Jul 28, 2007
    #3
  4. Merv Guest

    Suggest that the OP posts CATOS show version and show module output
    and IOS show version output
    Merv, Jul 28, 2007
    #4
  5. ufik Guest

    On 28 Lip, 23:56, Merv <> wrote:
    > Suggest that the OP posts CATOS show version and show module output
    > and IOS show version output


    WS-C5500 Software, Version McpSW: 5.5(13a) NmpSW: 5.5(13a)
    Copyright (c) 1995-2002 by Cisco Systems
    NMP S/W compiled on Feb 1 2002, 19:47:47
    MCP S/W compiled on Feb 01 2002, 19:41:58

    System Bootstrap Version: 5.1(2)

    Hardware Version: 1.3 Model: WS-C5500 Serial #: 069022666

    Mod Port Model Serial # Versions
    --- ---- ---------- --------- ----------------------------------------
    1 2 WS-X5530 022121735 Hw : 3.5
    Fw : 5.1(2)
    Fw1: 4.4(1)
    Sw : 5.5(13a)
    WS-F5531A 021601960 Hw : 2.1
    WS-U5534 022372489 Hw : 1.2
    3 9 WS-X5410 012879697 Hw : 1.0
    Fw : 4.2(1)
    Fw1: 4.2(1)
    Sw : 5.5(10)
    6 12 WS-X5201 009149143 Hw : 3.0
    Fw : 3.1(1)
    Sw : 5.5(13a)
    7 1 WS-X5302 006805398 Hw : 4.5
    Fw : 20.22
    Fw1: 2.2(4)
    Sw : 12.2(31)
    8 12 WS-X5011 005858615 Hw : 1.4
    Fw : 1.2
    Sw : 5.5(13a)
    9 12 WS-X5111 005077493 Hw : 1.0
    Fw : 1.3
    Sw : 5.5(13a)
    10 24 WS-X5224 015725951 Hw : 1.5
    Fw : 3.1(1)
    Sw : 5.5(13a)
    11 36 WS-X5239 024766488 Hw : 1.2
    Fw : 4.5(2)
    Sw : 5.5(13a)
    12 36 WS-X5239 024766361 Hw : 1.2
    Fw : 4.5(2)
    Sw : 5.5(13a)

    Router(boot)#sh ver
    Cisco Internetwork Operating System Software
    IOS (tm) C5RSM Software (C5RSM-BOOT-M), Version 12.2(31), RELEASE
    SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2005 by cisco Systems, Inc.
    Compiled Thu 11-Aug-05 16:25 by tinhuang
    Image text-base: 0x40010948, data-base: 0x4095E000

    ROM: System Bootstrap, Version 11.2(17523) [mohsen 102], INTERIM
    SOFTWARE
    BOOTLDR: C5RSM Software (C5RSM-BOOT-M), Version 12.2(31), RELEASE
    SOFTWARE (fc2)

    Router uptime is 8 hours, 7 minutes
    System returned to ROM by reload at 11:58:20 UTC Sat Jul 28 2007
    Running default software

    cisco RSP2 (R4700) processor with 131072K/2072K bytes of memory.
    R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
    Last reset from power-on
    G.703/E1 software, Version 1.0.
    G.703/JT2 software, Version 1.0.
    X.25 software, Version 3.0.0.
    1 C5IP controller (41 Vlan).
    41 Virtual Ethernet/IEEE 802.3 interface(s)
    123K bytes of non-volatile configuration memory.

    8192K bytes of Flash internal SIMM (Sector size 256K).
    Configuration register is 0x2102
    ufik, Jul 28, 2007
    #5
  6. Merv Guest

    Merv, Jul 29, 2007
    #6
  7. Scott Perry Guest

    Your question was about how to route from a VLAN on the switch to another
    VLAN on the switch through the RSM module.

    Routing is enabled by default on the RSM unless you disabled it or went
    through the prompted initial configuration. The command "ip routing" is
    only on the RSM.

    Make absolutely sure that VLAN 11 and VLAN 12 are configured on the switch
    and that there are ports assigned to each of those VLANs.

    It may not be a bad idea to also enable the switch and the router to access
    each other by IP:

    CatOS
    set interface sc0 98 10.1.1.2/255.255.255.252 10.1.1.1
    RSM
    interface vlan 98
    ip address 10.1.1.1 255.255.255.252
    no shutdown

    Here is your solution:

    CatOS
    set vlan 11
    set vlan 12
    set vlan 11 5/11
    set vlan 12 5/12
    RSM
    ip routing
    interface vlan 11
    ip address 89.9.64.65 255.255.255.192
    no shutdown
    interface vlan 12
    ip address 89.9.64.129 255.255.255.192
    no shutdown

    Even better would be to enable mulitlayer switching:

    CatOS
    set mls enable ip
    RSM
    mls rp ip

    --

    ===========
    Scott Perry
    ===========
    Indianapolis, Indiana
    ________________________________________
    <> wrote in message
    news:...
    > Hello,
    > I am trying configure communication beteewn vlan on catalyst 5500
    > with RSM WS-X5302 but I cant find command ip routing and router. What
    > can I do to !
    >
    > interface Vlan11
    > description xxx
    > ip address 89.9.64.65 255.255.255.192
    > no ip route-cache
    > !
    > interface Vlan12
    > description xxx
    > ip address 89.9.64.129 255.255.255.192
    > no ip route-cache
    >
    > Please help me.
    >
    Scott Perry, Jul 31, 2007
    #7
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. homer
    Replies:
    0
    Views:
    501
    homer
    Dec 3, 2003
  2. vedran

    PIX, RSM...

    vedran, Jan 23, 2004, in forum: Cisco
    Replies:
    1
    Views:
    675
    Walter Roberson
    Jan 23, 2004
  3. Cisco x5302 RSM

    , Jul 28, 2004, in forum: Cisco
    Replies:
    1
    Views:
    555
    Roman Nakhmanson
    Jul 28, 2004
  4. Yves
    Replies:
    4
    Views:
    537
    Andrey Tarasov
    Oct 21, 2004
  5. hari
    Replies:
    4
    Views:
    636
    Glen Grant
    Nov 14, 2004
Loading...

Share This Page