pix 506E and port forwarding

Discussion in 'Hardware' started by relar, Oct 3, 2008.

  1. relar

    relar

    Joined:
    Oct 3, 2008
    Messages:
    1
    first post, fairly new to the pix so if I'm an idiot, don't hesitate to tell me so.

    I have a pretty simple network, cable modem with static ip to pix to inside network.

    I have configured the pix to forward https, smtp rdp, and 3101 for BES, and it was working for several days, then suddenly stopped working.

    so I blew away the config and started over from scratch. it seemed to be working last night, then I get a call this morning that it isn't working.

    here's the config.

    : Saved
    : Written by enable_15 at 13:04:29.437 UTC Fri Oct 3 2008
    PIX Version 6.3(5)
    interface ethernet0 auto
    interface ethernet1 auto
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password DlXWECASe/EaOnXr encrypted
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol icmp error
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    access-list inbound permit tcp any host x.x.x.x eq smtp
    access-list inbound permit tcp any host x.x.x.x eq https
    access-list inbound permit tcp any host x.x.x.x eq 3389
    access-list inbound permit tcp any host x.x.x.x eq 3101
    pager lines 24
    icmp permit any outside
    icmp permit any inside
    mtu outside 1500
    mtu inside 1500
    ip address outside x.x.x.x 255.255.255.248
    ip address inside 10.0.0.252 255.0.0.0
    ip audit info action alarm
    ip audit attack action alarm
    pdm location 10.0.0.0 255.255.255.0 inside
    pdm location 10.0.0.0 255.0.0.0 inside
    pdm location 10.0.0.1 255.255.255.255 inside
    pdm location 10.0.0.7 255.255.255.255 inside
    pdm location 10.0.0.10 255.255.255.255 inside
    pdm location 10.0.0.50 255.255.255.255 inside
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0 0 0
    static (inside,outside) tcp x.x.x.x smtp 10.0.0.10 smtp netmask 255.255.255.255 0 0
    static (inside,outside) tcp x.x.x.x https 10.0.0.10 https netmask 255.255.255.255 0 0
    static (inside,outside) tcp x.x.x.x 3389 10.0.0.1 3389 netmask 255.255.255.255 0 0
    static (inside,outside) tcp x.x.x.x 3101 10.0.0.7 3101 netmask 255.255.255.255 0 0
    static (inside,outside) tcp x.x.x.x domain 10.0.0.1 domain netmask 255.255.255.255 0 0
    access-group inbound in interface outside
    rip outside default version 2
    rip inside passive version 2
    route outside 0.0.0.0 0.0.0.0 71.43.90.209 1
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout sip-disconnect 0:02:00 sip-invite 0:03:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server TACACS+ max-failed-attempts 3
    aaa-server TACACS+ deadtime 10
    aaa-server RADIUS protocol radius
    aaa-server RADIUS max-failed-attempts 3
    aaa-server RADIUS deadtime 10
    aaa-server LOCAL protocol local
    http server enable
    http 10.0.0.0 255.0.0.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    telnet 10.0.0.0 255.255.255.0 inside
    telnet timeout 5
    management-access inside
    console timeout 0
    terminal width 80
    : end

    I have rebooted the pix, replaced cables, it routes internet traffic fine, so I am fairly confident that it isn't a cabling issue. I did some troubleshooting with the isp, it is a business line so there are no ports being blocked. and when connected directly to the cable modem, I can access the ports remotely. so, I am very confused, as I said earlier, it seemed to be working last night, I tested it from http://www.mtgsy.net/dns/utilities.php and ran the port tester against it, as well as the ping test and it passed them all. any help would be greatly appreciated.

    Daniel
    relar, Oct 3, 2008
    #1
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Rodney Hall
    Replies:
    9
    Views:
    8,408
    Walter Roberson
    Jan 13, 2005
  2. Graeme Geldenhuys
    Replies:
    2
    Views:
    4,358
    Graeme Geldenhuys
    Apr 14, 2005
  3. tom.smith.iii@gmail.com

    port mapping or forwarding on Cisco Pix 506E

    tom.smith.iii@gmail.com, Aug 5, 2005, in forum: Cisco
    Replies:
    6
    Views:
    6,688
    Walter Roberson
    Aug 8, 2005
  4. ToyalP2
    Replies:
    7
    Views:
    1,516
    ToyalP2
    Jan 7, 2008
  5. uanmi
    Replies:
    0
    Views:
    425
    uanmi
    Feb 5, 2008
Loading...

Share This Page