ISDN Wont Accept and Transfer PSTN Calls To CCM "bad bearercap" (AS5350-CCM)

Discussion in 'VOIP' started by anonyme, Jan 28, 2005.

  1. anonyme

    anonyme Guest

    AS5350 Version 12.3(11)T2

    I want to Transfer Calls From ISDN to CCM ,
    The transfer call from PSTN to CCM doesn't work.
    When I try I have a busy line.

    I try this command on interface Serial3/0:15
    "isdn incoming-voice Voice", but "voice" done % Invalid input detected

    This is my config :
    ===================

    version 12.3
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    !
    hostname AS5350
    !
    boot-start-marker
    boot system flash c5350-is-mz.123-11.T2.bin
    no boot startup-test
    boot-end-marker
    !
    enable secret
    enable password
    !
    resource-pool disable
    calltracker enable
    calltracker history max-size 30
    calltracker call-record verbose
    spe default-firmware spe-firmware-1
    no voice-fastpath enable
    no aaa new-model
    ip subnet-zero
    !
    ip cef
    isdn switch-type primary-net5
    isdn logging
    !
    voice service voip
    fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
    cause-code legacy
    h323
    call start slow
    !
    fax interface-type fax-mail
    !
    controller E1 3/0
    framing NO-CRC4
    pri-group timeslots 1-16
    !
    interface Serial3/0:15
    no ip address
    isdn switch-type primary-net5
    isdn send-alerting
    isdn sending-complete
    no cdp enable
    !
    ip classless
    ip route 0.0.0.0 0.0.0.0 192.168.30.20
    no ip http server
    !
    map-class dialer test
    dialer voice-call
    !
    control-plane
    !
    voice-port 3/0:D
    bearer-cap 3100Hz
    !
    voice-port 3/1:D
    !
    no mgcp timer receive-rtcp
    no mgcp explicit hookstate
    !
    dial-peer voice 3000 voip
    destination-pattern T
    session target ipv4:192.168.30.205
    incoming called-number 9762
    dtmf-relay h245-alphanumeric
    codec g711ulaw
    !
    dial-peer voice 1 pots
    destination-pattern 0T
    direct-inward-dial
    port 3/0:D
    !
    ss7 mtp2-variant Bellcore 0
    ss7 mtp2-variant Bellcore 1
    ss7 mtp2-variant Bellcore 2
    ss7 mtp2-variant Bellcore 3
    !
    line con 0
    line aux 0
    line vty 0 4
    password xxx
    login
    line 1/00 1/59
    no flush-at-activation
    modem InOut
    !
    scheduler allocate 10000 400
    ntp clock-period 17180058
    ntp server 64.112.189.11
    end

    The debug and the error :
    =========================
    AS5350#sh debug


    The following ISDN debugs are enabled on all DSLs:

    debug isdn error is ON.
    debug isdn event is ON.
    debug isdn q931 is ON. (filter is OFF)
    debug isdn silent errors is ON.


    AS5350#
    *Jan 1 18:13:24.376: ISDN Se3/0:15 Q931: RX <- SETUP pd = 8 callref =
    0x0014
    Bearer Capability i = 0x9090A3
    Standard = CCITT
    Transer Capability = 3.1kHz Audio
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9838C
    Exclusive, Channel 12
    Progress Ind i = 0x8583 - Origination address is non-ISDN
    Calling Party Number i = 0x1081, '37797912345'
    Plan:Unknown, Type:International
    Called Party Number i = 0x81, '9762'
    Plan:ISDN, Type:Unknown
    Sending Complete
    *Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
    1/0x12 calltype 2 CALL_INCOMING
    *Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: call_incoming: call_id
    0x0012, Guid = Se3/0:15
    *Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
    call id 0x12 with a bad bearercap from 37797912345 on b channel 12
    *Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
    1/0x12 calltype 2 CALL_CLEARED
    *Jan 1 18:13:24.380: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8
    callref = 0x8014
    Cause i = 0x80D8 - Incompatible destination
    anonyme, Jan 28, 2005
    #1
    1. Advertising

  2. anonyme <> wrote in news:41fa209c$0$20494
    $:

    > *Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
    > call id 0x12 with a bad bearercap from 37797912345 on b channel 12


    You're receiving calls with bearer capability data, but expecting only
    voice?

    --
    Andreas
    Andreas Sikkema, Jan 28, 2005
    #2
    1. Advertising

  3. anonyme

    anonyme Guest

    (AS5350-CCM)

    Andreas Sikkema wrote:
    > anonyme <> wrote in news:41fa209c$0$20494
    > $:
    >
    >
    >>*Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
    >>call id 0x12 with a bad bearercap from 37797912345 on b channel 12

    >
    >
    > You're receiving calls with bearer capability data, but expecting only
    > voice?
    >

    Hi Andreas,

    Yes, for the moment I want only receive voice call

    Thanks in advance
    anonyme, Jan 28, 2005
    #3
  4. anonyme

    plugas

    Joined:
    May 2, 2008
    Messages:
    1
    I have the same problem:
    .May 2 18:47:58.519: ISDN Se3:15 **ERROR**: call_incoming: Received a call id 0xB95 with a bad bearercap from 25554469 on b channel 17
    .May 2 18:47:58.523: ISDN Se3:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8046
    Cause i = 0x80D8 - Incompatible destination

    but I'm not cisco operator. So, what do I have to ask to change on cisco?
    Bearer capability si wrong in this case?
    plugas, May 2, 2008
    #4
  5. anonyme

    ninop

    Joined:
    May 9, 2008
    Messages:
    3
    Location:
    Venezuela
    ok, I think it's inside the serial 3/0:15 config:

    try asking the router about the available options, like this:
    ===
    router(config-if)#isdn incoming-voice ?
    data Incoming voice calls will be handled as data.
    modem Incoming voice calls will be handled as modems.
    voice Incoming voice calls will be handled as voice.
    ===

    then, select isdn incoming-voice voice

    as example, this is my config, of my working cisco 3600 with a NM-HDV:

    ====
    interface Serial1/0:15
    no ip address
    encapsulation hdlc
    no logging event link-status
    isdn switch-type primary-qsig
    isdn protocol-emulate network
    isdn incoming-voice voice <-- Here I had to put this one so the calls are only voice, not data.
    no isdn T309-enable
    isdn T310 60000
    isdn send-alerting
    isdn bchan-number-order ascending
    isdn outgoing display-ie
    no cdp enable
    =======

    Hope this helps.
    ninop, May 9, 2008
    #5
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Darren
    Replies:
    0
    Views:
    963
    Darren
    Dec 3, 2003
  2. wr
    Replies:
    1
    Views:
    715
    News Account
    Feb 2, 2004
  3. Gio
    Replies:
    1
    Views:
    1,503
    Aaron Leonard
    Feb 23, 2004
  4. anonyme

    As5350 et CCM

    anonyme, Jan 17, 2005, in forum: VOIP
    Replies:
    7
    Views:
    2,116
    anonyme
    Jan 27, 2005
  5. Jim
    Replies:
    23
    Views:
    4,270
    Andy Repton
    May 8, 2006
Loading...

Share This Page