ISDN and VoIP configuration

Discussion in 'Cisco' started by clmx_jleudo@yahoo.com, Oct 6, 2005.

  1. Guest

    Hi Fellows

    I need a little help to fix a problem that I have already trying to
    receive calls in a Cisco GW 2610, basically I want to receive some
    calls coming from the PSTN and sent these to and IP-PBX using SIP, when
    a dial I got dial tone and few seconds later the call is discconected,
    the call is received by the router but is not routed to the other end
    thru SIP.

    If you can take a look to this y will appreciate any help on this:


    1d07h: ISDN Se1/0:23: Ux_BadMsg(): Invalid Message for call state 10,
    call id 0x2B, call ref 0x805A, event 0x62

    1d07h: ISDN Se1/0:23: TX -> STATUS pd = 8 callref = 0x805A

    1d07h: Cause i = 0x80E562 - Message not compatible with call
    state

    1d07h: Call State i = 0x0A

    1d07h: ISDN Se1/0:23: TX -> DISCONNECT pd = 8 callref = 0x805A

    1d07h: Cause i = 0x809C - Invalid number format (incomplete
    number)


    ============================
    a different log
    ==========================



    1d06h: ISDN Se1/0:23: Incoming call id = 0x001D, dsl 0

    1d06h: ISDN Se1/0:23: NegotiateBchan: bchan 1 intid 0 serv_st 0 chan_st
    0 callid 0x0000 ev 0x90 n/w? 0

    1d06h: Negotiated int_id 0 bchan 0 cr=0x804D callid=0x001D lo_chan 1
    final int_id/bchan 0/1 cause 0x0

    1d06h: ISDN Se1/0:23: LIF_EVENT: ces/callid 1/0x1D CALL_INCOMING

    1d06h: ISDN Se1/0:23: CALL_INCOMING dsl 0 bchan 0

    1d06h: ISDN Se1/0:23: CALL_INCOMING: call type is VOICE ULAW, bchan = 0

    1d06h: ISDN Se1/0:23: Event: Received a VOICE call from 3059842692 on
    B0 at 64 Kb/s

    1d06h: ISDN Se1/0:23: process_pri_simple(): msg 74, call id 0x1D, bchan
    0, call type VOICE

    1d06h: ISDN Se1/0:23: process_disconnect(): call id 0x1D, call type is
    VOICE, b_idb 0x82346678, ces 1, cause No route to destination(0x3)

    1d06h: ISDN Se1/0:23: CCPRI_ReleaseCall(): bchan 1, call id 0x1D, call
    type VOICE

    1d06h: CCPRI_ReleaseChan released b_dsl 0 B_Chan 1

    1d06h: ISDN Se1/0:23: LIF_EVENT: ces/callid 1/0x1D CALL_CLEARED

    1d06h: ISDN Se1/0:23: received CALL_CLEARED call_id 0x1D

    1d06h: no resend setup, no redial

    ==================================
    Part of the configuration
    ==================================

    What I'm missing here?

    !

    no ip dhcp-client network-discovery

    isdn switch-type primary-ni

    !

    voice service voip

    !

    controller T1 1/0

    framing esf

    linecode b8zs

    pri-group timeslots 1-24

    !
    interface Ethernet0/0

    description To LAN

    ip address 192.168.1.34 255.255.255.0

    full-duplex

    !

    interface Serial0/0

    no ip address

    shutdown

    !

    interface Serial0/1

    no ip address

    shutdown

    !

    interface Serial1/0:23

    no ip address

    no logging event link-status

    isdn switch-type primary-ni

    isdn incoming-voice voice

    isdn calling-number 3056777888

    isdn sent-alerting

    no cdp enable

    !

    ip classless

    no ip http server

    !

    call rsvp-sync
    !

    voice-port 1/0:23
    !

    mgcp profile default

    dial-peer cor custom

    !

    dial-peer voice 2 pots

    incoming called-number 30567778..

    direct-inward-dial

    !

    dial-peer voice 200 voip

    destination-pattern 30567778..

    session target ipv4:192.168.1.25

    codec g711ulaw

    !
    !

    !

    end
    , Oct 6, 2005
    #1
    1. Advertising

  2. Jonathan Guest

    <> wrote in message
    news:...
    > Hi Fellows
    >
    > I need a little help to fix a problem that I have already trying to
    > receive calls in a Cisco GW 2610, basically I want to receive some
    > calls coming from the PSTN and sent these to and IP-PBX using SIP, when
    > a dial I got dial tone and few seconds later the call is discconected,
    > the call is received by the router but is not routed to the other end
    > thru SIP.
    >
    > If you can take a look to this y will appreciate any help on this:
    >


    Run a "debug isdn q931" and make a test call. Post the results.

    I am pretty sure you are not sending these as unknown/unknown and that is
    why it is failing, but I want to check (or, you could be sending them
    unknown/unknown and it is looking for national/unknown, etc...)





    Jonathan
    Jonathan, Oct 6, 2005
    #2
    1. Advertising

  3. Guest

    HI Jonathan

    The numbers are showing as National instead of Unknown I will made the
    change, but here is how it is from the begining:

    IPGateway(config-if)#
    1d07h: ISDN Se1/0:23: RX <- SETUP pd = 8 callref = 0x0059
    1d07h: Bearer Capability i = 0x8090A2
    1d07h: Channel ID i = 0xA98381
    1d07h: Facility i =
    0x9F8B0100A10F02010106072A8648CE1500040A0100
    1d07h: Calling Party Number i = 0x2183, '7862109319',
    Plan:ISDN, Type:National
    1d07h: Called Party Number i = 0xA1, '3056777888', Plan:ISDN,
    Type:National
    1d07h: ISDN Se1/0:23: TX -> CALL_PROC pd = 8 callref = 0x8059
    1d07h: Channel ID i = 0xA98381
    1d07h: ISDN Se1/0:23: TX -> DISCONNECT pd = 8 callref = 0x8059
    1d07h: Cause i = 0x8083 - No route to destination
    1d07h: ISDN Se1/0:23: RX <- RELEASE pd = 8 callref = 0x0059
    1d07h: ISDN Se1/0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8059
    1d07h: ISDN Se1/0:23: RX <- SETUP pd = 8 callref = 0x005A
    1d07h: Bearer Capability i = 0x8090A2
    1d07h: Channel ID i = 0xA98381
    1d07h: Facility i =
    0x9F8B0100A10F02010106072A8648CE1500040A0100
    1d07h: Calling Party Number i = 0x2183, '7862109319',
    Plan:ISDN, Type:National
    1d07h: Called Party Number i = 0xA1, '3056777810', Plan:ISDN,
    Type:National
    1d07h: ISDN Se1/0:23: TX -> CALL_PROC pd = 8 callref = 0x805A
    1d07h: Channel ID i = 0xA98381
    1d07h: ISDN Se1/0:23: TX -> CONNECT pd = 8 callref = 0x805A
    1d07h: ISDN Se1/0:23: RX <- CONNECT_ACK pd = 8 callref = 0x005A
    1d07h: ISDN Se1/0:23: CALL_PROGRESS: CALL_CONNECTED call id 0x2B, bchan
    0, dsl 0
    1d07h: ISDN Se1/0:23: RX <- FACILITY pd = 8 callref = 0x005A
    1d07h: Facility i =
    0x9F8B0100A117020101020100800F4C4555444F2C4A4F484E2020202020
    1d07h: ISDN Se1/0:23: Ux_BadMsg(): Invalid Message for call state 10,
    call id 0x2B, call ref 0x805A, event 0x62
    1d07h: ISDN Se1/0:23: TX -> STATUS pd = 8 callref = 0x805A
    1d07h: Cause i = 0x80E562 - Message not compatible with call
    state
    1d07h: Call State i = 0x0A
    1d07h: ISDN Se1/0:23: TX -> DISCONNECT pd = 8 callref = 0x805A
    1d07h: Cause i = 0x809C - Invalid number format (incomplete
    number)
    1d07h: Facility i =
    0x9F8B0100A10F02010106072A8648CE1500040A0100
    1d07h: ISDN Se1/0:23: RX <- RELEASE pd = 8 callref = 0x005A
    1d07h: ISDN Se1/0:23: TX -> RELEASE_COMP pd = 8 callref = 0x805A
    , Oct 12, 2005
    #3
  4. Guest

    genius Jonathan

    That was my issue I set numbering-type as unknown and it works fine
    now. Thanx a lot
    , Oct 12, 2005
    #4
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. BobCov
    Replies:
    3
    Views:
    587
    Andre Beck
    Nov 21, 2003
  2. SkY
    Replies:
    0
    Views:
    942
  3. Martin Maurer
    Replies:
    5
    Views:
    14,571
    moc.hooha
    Nov 7, 2008
  4. sync
    Replies:
    0
    Views:
    557
  5. BE749309
    Replies:
    0
    Views:
    1,195
    BE749309
    Jun 9, 2010
Loading...

Share This Page