IP Dhcp -- No Comments

Discussion in 'Cisco' started by Victor, Jan 13, 2005.

  1. Victor

    Victor Guest

    Just look line by line

    CCME(config)#ip dhcp pool TelfIP
    CCME(dhcp-config)#host 192.168.1.4 ?
    /nn or A.B.C.D Network mask or prefix length
    <cr>

    CCME(dhcp-config)#host 192.168.1.4/32
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#
    192.168.1.4/32(config)#^Z
    192.168.1.4/32#^Z
    *Mar 29 01:07:25.375: %SYS-5-CONFIG_I: Configured from console by vty0
    (192.168.0.17)
    192.168.1.4/32#
    192.168.1.4/32#
    192.168.1.4/32#
    192.168.1.4/32#conf ter
    Enter configuration commands, one per line. End with CNTL/Z.
    192.168.1.4/32(config)#hostname CMME
    CMME(config)#
    CMME(config)#



    CMME#show ver
    Cisco IOS Software, C1700 Software (C1700-IPVOICE-M), Version
    12.3(4)T4, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2004 by Cisco Systems, Inc.
    Compiled Thu 11-Mar-04 18:28 by eaarmas

    ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)

    CMME uptime is 9 minutes
    System returned to ROM by reload at 21:01:22 GMT Thu Mar 28 2002
    System image file is "flash:c1700-ipvoice-mz.123-4.T4.bin"

    Cisco 1760 (MPC860P) processor (revision 0x500) with 86852K/11452K
    bytes of memory.
    Processor board ID FOC081329BK (224910893), with hardware revision 0000
    MPC860P processor: part number 5, mask 2
    1 FastEthernet interface
    2 Serial(sync/async) interfaces
    2 Voice FXO interfaces
    32K bytes of NVRAM.
    32768K bytes of processor board System flash (Read/Write)
    Configuration register is 0x2102
    Victor, Jan 13, 2005
    #1
    1. Advertising

  2. Victor

    Ivan Ostreš Guest

    In article <>,
    says...
    > Just look line by line
    >
    >


    Not a strange thing to get from T-train IOS.

    --
    -Ivan.

    *** Use Rot13 to see my eMail address ***
    Ivan Ostreš, Jan 13, 2005
    #2
    1. Advertising

  3. Victor

    Victor Guest

    Yeah you are right Ivan, but DHCP is written since 12.0[2]T (so..)


    Ivan Ostreš wrote:
    > In article <>,
    > says...
    > > Just look line by line
    > >
    > >

    >
    > Not a strange thing to get from T-train IOS.
    >
    > --
    > -Ivan.
    >
    > *** Use Rot13 to see my eMail address ***
    Victor, Jan 13, 2005
    #3
  4. Victor

    Ivan Ostreš Guest

    In article <>,
    says...
    >
    > Yeah you are right Ivan, but DHCP is written since 12.0[2]T (so..)
    >


    I'll have to correct you on this... it was written in 12.0(something)
    for the FIRST time. There's been a lot of changes in that module since
    it was first time out.

    --
    -Ivan.

    *** Use Rot13 to see my eMail address ***
    Ivan Ostreš, Jan 13, 2005
    #4
  5. Looks like this is probably a day-one bug; I found it in current 12.2M,
    12.3M, 12.3T.

    Cheers,

    Aaron

    ---

    CSCsa54008
    Externally found minor defect: New (N)
    ill formatted DHCP host value is parsed as global hostname

    Release-note: Added 050114 by aaron

    If one enters, while in dhcp-config mode, an ill formatted value for
    the host IP address/mask, this is instead parsed as the global-config
    "hostname" command. Example:

    router(config)#ip dhcp pool FOO
    router(dhcp-config)#host 10.1.1.1/26
    % Hostname contains one or more illegal characters.

    % Hostname "10.1.1.1/26" is not a legal LAT node name, Using "CISCO_FB8000"
    10.1.1.1/26(config)#

    Workaround: restore the hostname to its original value, then enter
    the host IP address/mask correctly (note the space between the address
    and the mask):

    10.1.1.1/26(config)#hostname router
    router(config)#ip dhcp pool FOO
    router(dhcp-config)#host 10.1.1.1 /26
    router(dhcp-config)#

    ---


    On 13 Jan 2005 05:20:28 -0800, "Victor" <> wrote:

    ~ Just look line by line
    ~
    ~ CCME(config)#ip dhcp pool TelfIP
    ~ CCME(dhcp-config)#host 192.168.1.4 ?
    ~ /nn or A.B.C.D Network mask or prefix length
    ~ <cr>
    ~
    ~ CCME(dhcp-config)#host 192.168.1.4/32
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#
    ~ 192.168.1.4/32(config)#^Z
    ~ 192.168.1.4/32#^Z
    ~ *Mar 29 01:07:25.375: %SYS-5-CONFIG_I: Configured from console by vty0
    ~ (192.168.0.17)
    ~ 192.168.1.4/32#
    ~ 192.168.1.4/32#
    ~ 192.168.1.4/32#
    ~ 192.168.1.4/32#conf ter
    ~ Enter configuration commands, one per line. End with CNTL/Z.
    ~ 192.168.1.4/32(config)#hostname CMME
    ~ CMME(config)#
    ~ CMME(config)#
    ~
    ~
    ~
    ~ CMME#show ver
    ~ Cisco IOS Software, C1700 Software (C1700-IPVOICE-M), Version
    ~ 12.3(4)T4, RELEASE SOFTWARE (fc2)
    ~ Technical Support: http://www.cisco.com/techsupport
    ~ Copyright (c) 1986-2004 by Cisco Systems, Inc.
    ~ Compiled Thu 11-Mar-04 18:28 by eaarmas
    ~
    ~ ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
    ~
    ~ CMME uptime is 9 minutes
    ~ System returned to ROM by reload at 21:01:22 GMT Thu Mar 28 2002
    ~ System image file is "flash:c1700-ipvoice-mz.123-4.T4.bin"
    ~
    ~ Cisco 1760 (MPC860P) processor (revision 0x500) with 86852K/11452K
    ~ bytes of memory.
    ~ Processor board ID FOC081329BK (224910893), with hardware revision 0000
    ~ MPC860P processor: part number 5, mask 2
    ~ 1 FastEthernet interface
    ~ 2 Serial(sync/async) interfaces
    ~ 2 Voice FXO interfaces
    ~ 32K bytes of NVRAM.
    ~ 32768K bytes of processor board System flash (Read/Write)
    ~ Configuration register is 0x2102
    Aaron Leonard, Jan 14, 2005
    #5
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. =?Utf-8?B?SGVpbkQ=?=

    Wireless DHCP clients cannot obtain an IP address from the DHCP se

    =?Utf-8?B?SGVpbkQ=?=, Jan 8, 2006, in forum: Wireless Networking
    Replies:
    0
    Views:
    2,811
    =?Utf-8?B?SGVpbkQ=?=
    Jan 8, 2006
  2. Ingo Hauf

    if Active Directory no DHCP? or: Where ist my DHCP

    Ingo Hauf, Oct 17, 2003, in forum: Computer Support
    Replies:
    2
    Views:
    499
    Ralph Wade Phillips
    Oct 18, 2003
  3. Fayza
    Replies:
    3
    Views:
    12,648
    Dan Shea
    May 12, 2004
  4. Vimokh
    Replies:
    3
    Views:
    5,595
    Vimokh
    Sep 6, 2006
  5. sonicgravy
    Replies:
    0
    Views:
    1,415
    sonicgravy
    Nov 13, 2006
Loading...

Share This Page