Content Engine 590

Discussion in 'Cisco' started by Jodie, Jul 23, 2005.

  1. Jodie

    Jodie Guest

    Hello!

    I am trying to configure a Content Engine 590 that was recently given
    to me. I do not know the reason why this device was retired before
    being given to me. So, I may be chasing a ghost. But, until I can
    confirm a hardware failure of some sort, I am sure it can be made to
    work.

    Here is the console output when I boot it up. I have tried *** for
    recovery and without. I get the same results either way. At the
    bottom, it starts complaining of disk errors. Just before it shows the
    disk erors, it prompts for a username, but will not accept input. I
    would appreciate help on this matter as I need to get this working
    quickly.

    Thanks!
    Jodie


    Initializing memory. Please wait.
    BIOS Version: CE500 01.11
    BIOS Build date: 07/27/00
    Symbios, Inc. SDMS (TM) V4.0 PCI SCSI BIOS, PCI Rev. 2.0, 2.1
    Copyright 1995, 1998 Symbios, Inc.
    PCI-4.11.00

    HBA ID LUN VENDOR PRODUCT REV SYNC WIDE INT13 CYL/ HD/SEC
    --- -- --- -------- ---------------- ---- ---- ---- ----- ------------
    0 0 0 IBM DDYS-T18350M S80D 80.0 16 BOOT 1024/255/63
    0 1 0 IBM DDYS-T18350M S80D 80.0 16 81h 1024/255/63
    0 7 0 Symbios SYM53C895 0002 80.0 16

    Symbios, Inc. PCI boot ROM successfully installed!
    Cisco CE Booting From Flash.
    [BOOT-ASM]
    [BOOT-PHASE2]: entered
    [BOOT-PHASE2]: build date: Wed May 30 10:03:59 PDT 2001, build number 1
    [BOOT-PHASE2]: directory verified ok
    [BOOT-PHASE2]: examining phase3 boot-rom: 'default_bootrom'
    [BOOT-PHASE3]: entered
    [BOOT-PHASE3]: version 1, built Wed May 30 10:03:59 PDT 2001
    [BOOT-PHASE3]: directory verified ok
    timeoutHASE3]: enter `***' for rescue image: ***
    [BOOT-PHASE3]: default system image is 78 sectors
    [BOOT-PHASE3]: loaded 78 device sectors to 0x2000000!
    [BOOT-PHASE3]: extracting system image at 0x2000000
    [BOOT-PHASE3]: loading kernel
    [BOOT-PHASE3]: system image header: v=2, b=893827, i=9219641
    [BOOT-PHASE3]: rd set at 0x6000000, len 9219641
    [BOOT-PHASE3]: moving 3072 code bytes to 0x90000
    [BOOT-PHASE3]: checksum of relocated ramdisk (6000000) is
    2a5dc12f17f3ead14c1a2439392c8a2f
    [BOOT-PHASE3]: invoking kernel now
    [BOOT-PHASE2]: booting kernel
    Linux version 2.3.36.csco (bbalagot@vista2) (gcc version egcs-2.91.66
    19990314/Linux (egcs-1.1.2 release)) #1 SMP Wed May 30 09:54:51 PDT
    2001
    setup.c: E820 fixup: old map: 5 entries; new map: 7 entries
    e820: 0009ec00 @ 00000000 (usable)
    e820: 00001400 @ 0009ec00 (reserved)
    e820: 0001f800 @ 000e0800 (reserved)
    e820: 00e00000 @ 00100000 (usable)
    e820: 00100000 @ 00f00000 (reserved)
    e820: 3f000000 @ 01000000 (usable)
    e820: 00100000 @ fff00000 (reserved)
    Scan SMP from 7c000000 for 1024 bytes.
    Scan SMP from 7c09fc00 for 1024 bytes.
    Scan SMP from 7c0f0000 for 65536 bytes.
    Scan SMP from 7c09ec00 for 4096 bytes.
    setup.c: reserved bootmem for INITRD_START = 0x6000000, INITRD_SIZE =
    9219641
    mapped APIC to ffffe000 (01000000)
    On node 0 totalpages: 00040000
    zone(0): 4096 pages.
    zone(1): 258048 pages.
    zone(2): 0 pages.
    Detected 598412973 Hz processor.
    Console: colour *CGA 15x25
    Calibrating delay loop... 596.38 BogoMIPS
    kdb version 1.3 by Scott Lurndal. Copyright SGI, All Rights Reserved
    Memory: 1015056k/1048576k available (1596k kernel code, 32104k
    reserved, 181k data, 388k init, 0k highmem)
    Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
    Pentium-III serial number disabled.
    Checking 386/387 coupling... OK, FPU using exception 16 error
    reporting.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    Pentium-III serial number disabled.
    per-CPU timeslice cutoff: 50.03 usecs.
    CPU0: Intel Pentium III (Coppermine) stepping 03
    SMP motherboard not detected. Using dummy APIC emulation.
    Initializing CPU#0
    calibrating APIC timer ...
    ...... CPU clock speed is 598.4278 MHz.
    ...... host bus clock speed is 0.0000 MHz.
    cpu: 0, clocks: 0, slice: 0, nr: 1.
    CPU0<C0:0,C:0,D:0,S:0,C:0>
    Setting commenced=1, go go go
    PCI: PCI BIOS revision 2.10 entry at 0xe9b9c
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    PCI: Cannot allocate resource region 2 of device 00:0d.0
    PCI: Cannot allocate resource region 2 of device 00:0e.0
    PCI: Allocation of memory region 00:0d.0/2 (-1609564160 bytes) failed
    PCI: Allocation of memory region 00:0e.0/2 (-1609564160 bytes) failed
    Limiting direct PCI/PCI transfers.
    Linux NET4.0 for Linux 2.3
    Based upon Swansea University Computer Society NET3.039
    skb_init: memory pools configured to steal max 150994944 bytes (144MB)
    for skbuff memory
    skb_init: pool locking done by local_irq_save/local_irq_restore, 4 CPUs
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP
    TCP: Hash tables configured (established 65536 bind 65536)
    Starting kswapd v1.6
    Serial driver version 4.91 (1999-11-17) with<4>Keyboard timeout[2]
    Keyboard timeout[2]
    MANY_PORTS SHARE_IRQ SERIAL_PCI PCI_IOMEM enabled
    ttyS00 at 0x03f8 (irq = 4) is a 16550A
    ttyS01 at 0x02f8 (irq = 3) is a 16550A
    pty: 256 Unix98 ptys configured
    Linux video capture interface: v1.00
    DIAMOND-RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
    blocksize
    DIAMOND-RAMDISK: Found compressed initrd image
    DIAMOND_RAMDISK: compressed_read: ramdisk md5sum:
    2a5dc12f17f3ead14c1a2439392c8a2f
    DIAMOND-RAMDISK: allocate_ramdisk_space [rd 0]: map is 0x828f0000
    DIAMOND-RAMDISK: diamond_crd_load (end):
    2a5dc12f17f3ead14c1a2439392c8a2f
    DIAMOND-RAMDISK: compressed_free called!
    DIAMOND-RAMDISK: compressed_free: NOT CALLING free_initrd_mem!
    DIAMOND-RAMDISK: diamond_rd_init returns
    Uniform Multi-Platform E-IDE driver Revision: 6.21
    PIIX4: IDE controller on PCI bus 00 dev 39
    PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
    Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
    FDC 0 is a post-1991 82077
    sym53c8xx: at PCI bus 0, device 15, function 0
    sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
    sym53c8xx: 53c895 detected with Symbios NVRAM
    sym53c895-0: rev 0x2 on pci bus 0 device 15 function 0 irq 5
    sym53c895-0: Symbios format NVRAM, ID 7, Fast-40, Parity Checking
    sym53c895-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
    07/4e/a0/01/00/24
    sym53c895-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex)
    07/4e/80/00/08/24
    sym53c895-0: on-chip RAM at 0xa0081000
    sym53c895-0: resetting, command processing suspended for 2 seconds
    sym53c895-0: restart (scsi reset).
    sym53c895-0: enabling clock multiplier
    sym53c895-0: Downloading SCSI SCRIPTS.
    scsi0 : sym53c8xx - version 1.5g
    scsi : 1 host.
    sym53c895-0: command processing resumed
    Vendor: IBM Model: DDYS-T18350M Rev: S80D
    Type: Direct-Access ANSI SCSI revision: 03
    Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
    Vendor: IBM Model: DDYS-T18350M Rev: S80D
    Type: Direct-Access ANSI SCSI revision: 03
    Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
    sym53c895-0-<0,0>: tagged command queue depth set to 4
    sym53c895-0-<1,0>: tagged command queue depth set to 4
    scsi : detected 2 SCSI disks total.
    sym53c895-0-<0,*>: WIDE SCSI (16 bit) enabled.
    sym53c895-0-<0,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31)
    SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB]
    [17.5 GB]
    sym53c895-0-<1,*>: WIDE SCSI (16 bit) enabled.
    sym53c895-0-<1,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31)
    SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB]
    [17.5 GB]
    eepro100.c:v1.09j 7/27/99 Donald Becker
    http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
    eth0: Intel PCI EtherExpress Pro100 at 0xbc804000, 00:30:85:87:5B:00,
    IRQ 9.
    Board assembly 668081-002, Physical connectors present: RJ45
    Primary interface chip i82555 PHY #1.
    General self-test: passed.
    Serial sub-system self-test: passed.
    Internal registers self-test: passed.
    ROM checksum self-test: passed (0x04f4518b).
    Receiver lock-up workaround activated.
    eth1: Intel PCI EtherExpress Pro100 at 0xbc806000, 00:30:85:87:5B:01,
    IRQ 10.
    Board assembly 668081-002, Physical connectors present: RJ45
    Primary interface chip i82555 PHY #1.
    General self-test: passed.
    Serial sub-system self-test: passed.
    Internal registers self-test: passed.
    ROM checksum self-test: passed (0x04f4518b).
    Receiver lock-up workaround activated.
    eepro100.c:v1.09j 7/27/99 Donald Becker
    http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
    Partition check:
    sda: sda1 sda2 sda3 sda4
    sdb: sdb1
    Cisco ContentEngine Flash Driver Version 0.01
    wccp: v1.00 (20000327), debug=0
    wccp_list_bypass v1.0.0
    wccp_list_bypass tuple allocated 20480
    DIAMOND-RAMDISK: drd_open called w/ dev 0x0
    EXT2-fs warning: checktime reached, running e2fsck is recommended
    VFS: Mounted root (ext2 filesystem).
    Freeing unused kernel memory: 388k freed
    INIT: version 2.78 booting
    Content Engine application software initializing
    Mounting non-disk filesystems
    Set clock: Sat Jul 23 21:31:19 EDT 2005
    Loading kernel module ipchains.o
    Upping loopback interface
    setting $TERM to vt100
    set /proc/sys/fs/file-max to 65536
    set /proc/sys/net/ipv4/ip_local_port_range to 10000 61000
    set /proc/sys/kernel/shmmax to 268435456
    set /proc/sys/net/core/rmem_max to 131072
    set /proc/sys/net/core/wmem_max to 131072
    calculated checksum: 38c9506fcbacd339d1d22a0c59778552
    embedded md5sum : 00000000000000000000000000000000
    calculated eth0 mac: 00:30:85:87:5b:00
    embedded eth0 mac : 00:30:85:87:5b:00
    other cookie info:
    HWVersion: 12
    PartNumber: 128 0 133 121 1
    BoardRevision: 2
    SerialNumber: 83 67 75 48 53 48 51 48 48 56 87
    TestDate: 19-2-2001
    ChipRev: 176
    ModelNum: 67 69 53 57 48
    VendID: 2
    CookieVer: 2
    ExtModel: <N/A>
    Chksum: 0x3f
    INIT: Entering runlevel: 3
    Entering non-interactive startup
    Starting cron daemon: [ OK ]


    Cisco Content Engine Console

    Partition disk00/00 identified as SWFS
    disk00/00 has minor problem, but fixed. Return code = 1
    Partition disk00/01 identified as SYSFS
    disk00/01 has minor problem, but fixed. Return code = 1
    Partition disk00/02 identified as MEDIAFS
    disk00/02 has minor problem, but fixed. Return code = 1
    Partition disk00/03 identified as CFS
    Partition disk01/00 identified as CFS
    disk02 is missing. Host: 0, Channel: 0, Scsi ID: 8
    disk03 is missing. Host: 0, Channel: 0, Scsi ID: 9
    disk04 is missing. Host: 0, Channel: 0, Scsi ID: 10
    disk05 is missing. Host: 0, Channel: 0, Scsi ID: 11
    disk06 is missing. Host: 0, Channel: 0, Scsi ID: 12
    disk07 is missing. Host: 0, Channel: 0, Scsi ID: 13
    disk00 (scsi host 0, channel 0, id 0)
    disk01 (scsi host 0, channel 0, id 1)
    disk02 (scsi host 0, channel 0, id 8) NOT available
    disk03 (scsi host 0, channel 0, id 9) NOT available
    disk04 (scsi host 0, channel 0, id 10) NOT available
    disk05 (scsi host 0, channel 0, id 11) NOT available
    disk06 (scsi host 0, channel 0, id 12) NOT available
    disk07 (scsi host 0, channel 0, id 13) NOT available
    Mounting disk00/00 as SWFS ...succeeded
    Mounting disk00/01 as SYSFS ...succeeded
    Mounting disk00/02 as MEDIAFS ...succeeded
    Disk configuration is initialized
     
    Jodie, Jul 23, 2005
    #1
    1. Advertising

  2. Hi Jodie,

    You may want to try:

    username: admin

    password: default

    Sincerely,

    Brad Reese
    BradReese.Com Cisco Repair Service Experts
    1293 Hendersonville Road, Suite 17
    Asheville, North Carolina USA 28803
    U.S. Toll Free: 877-549-2680
    International: 828-277-7272
    Website: http://www.bradreese.com/cisco-big-iron-repair.htm
     
    www.BradReese.Com, Jul 24, 2005
    #2
    1. Advertising

  3. Jodie

    Jodie Guest

    Hi Brad,

    Thanks for your response. What I meant by not accepting any input is
    that when I enter admin as the username and <cr>, nothing happens. It
    never even prompts for the password. In fact, if I am not quick enough
    to enter admin, the disk errors will start and then I really cannot do
    anything. However, even if I enter admin <cr> before the disk errors,
    nothing happens.

    Thanks!
    Jodie
     
    Jodie, Jul 24, 2005
    #3
  4. Jodie,

    Your post above states,

    "Symbios, Inc. PCI boot ROM successfully installed!
    Cisco CE Booting From Flash."

    ---------------------------------------------------------------------------

    The Cisco 590 Field Notice states,

    "Your CDN device may have been configured to boot from flash instead of
    from disk.

    The CDN software must be booted from disk.

    Some CE-590-CDNs were shipped from manufacturing with the flag set to
    boot from flash instead of from disk.

    The CDN software needs to be loaded from disk.

    Manufacturing has since rectified this problem, however some units in
    the field may be configured to boot from flash."

    http://www.cisco.com/en/US/products/hw/contnetw/ps761/products_field_notice09186a0080094bea.shtml

    Cisco 590 Support Documentation:

    http://www.cisco.com/en/US/products/hw/contnetw/ps761/tsd_products_support_series_home.html

    Brad Reese
    http://www.BradReese.Com
     
    www.BradReese.Com, Jul 24, 2005
    #4
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. TMAN

    Content Engine 590

    TMAN, Jul 18, 2003, in forum: Cisco
    Replies:
    0
    Views:
    706
  2. alnasser
    Replies:
    1
    Views:
    451
    Gary G. Taylor
    Oct 1, 2004
  3. Silverstrand
    Replies:
    0
    Views:
    699
    Silverstrand
    May 23, 2006
  4. Silverstrand
    Replies:
    0
    Views:
    1,204
    Silverstrand
    Nov 21, 2006
  5. Ian
    Replies:
    0
    Views:
    1,083
Loading...

Share This Page