Clear ATM0.1 point-to-point entry.

Discussion in 'Cisco' started by AM, Feb 4, 2005.

  1. AM

    AM Guest

    I created that interface.

    I would completely clear it, but giving "no inter atm0.1" the router tells me

    "Not all config may be removed and may reappear after reactivating the sub-interface"

    and "show ip interf brief" reports me

    Interface IP-Address OK? Method Status Protocol
    ATM0 unassigned YES NVRAM up up
    ATM0.1 unassigned YES unset deleted down
    .............................

    Alex.
     
    AM, Feb 4, 2005
    #1
    1. Advertising

  2. AM

    AM Guest

    AM wrote:
    > I created that interface.
    >
    > I would completely clear it, but giving "no inter atm0.1" the router
    > tells me
    >
    > "Not all config may be removed and may reappear after reactivating the
    > sub-interface"
    >
    > and "show ip interf brief" reports me
    >
    > Interface IP-Address OK? Method
    > Status Protocol
    > ATM0 unassigned YES NVRAM
    > up up
    > ATM0.1 unassigned YES unset
    > deleted down
    > ............................
    >
    > Alex.


    I did

    conf t
    default interface ATM 0

    and this is the output

    Interface IP-Address OK? Method Status Protocol
    ATM0 unassigned YES TFTP up up
    Dialer1 unassigned YES unset up up
    ....................
     
    AM, Feb 4, 2005
    #2
    1. Advertising

  3. > I created that interface.
    >
    > I would completely clear it, but giving "no inter atm0.1" the router
    > tells me
    >
    > "Not all config may be removed and may reappear after reactivating the
    > sub-interface"
    >
    > and "show ip interf brief" reports me
    >
    > Interface IP-Address OK? Method
    > Status Protocol
    > ATM0 unassigned YES NVRAM
    > up up
    > ATM0.1 unassigned YES unset
    > deleted down
    > ............................
    >
    > Alex.



    do a reboot after saving your config and the interface ATM0.1 will be
    sent to oblivion.
     
    Helmut Ulrich, Feb 4, 2005
    #3
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Joop van der Velden

    explanation of "show dsl int atm0"?

    Joop van der Velden, Feb 2, 2005, in forum: Cisco
    Replies:
    2
    Views:
    16,025
    Joop van der Velden
    Feb 3, 2005
  2. Tom Pouce

    Show dsl int atm0

    Tom Pouce, Feb 11, 2005, in forum: Cisco
    Replies:
    0
    Views:
    673
    Tom Pouce
    Feb 11, 2005
  3. elmar bschorer

    dsl atm0 disable

    elmar bschorer, Feb 14, 2005, in forum: Cisco
    Replies:
    1
    Views:
    1,369
  4. Tirenque
    Replies:
    5
    Views:
    9,564
    Charlie Root
    Mar 21, 2006
  5. AM
    Replies:
    2
    Views:
    780
    Doug McIntyre
    Jun 23, 2006
Loading...

Share This Page