Cisco 1242ag AP downgrade to autonomous mode failure

Discussion in 'Cisco' started by muanivanua, Jun 23, 2009.

  1. muanivanua

    muanivanua

    Joined:
    Jun 4, 2008
    Messages:
    2
    Hi all,

    I am not able to get CLI access to cisco 1242ag ap after downgrading to autonommous mode from lwapp mode. interface kips resetting.

    the following is the capture txt from the AP.

    ---------------------------------
    Xmodem file system is available.
    flashfs[0]: 137 files, 7 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 4447232
    flashfs[0]: Bytes available: 11551744
    flashfs[0]: flashfs fsck took 26 seconds.
    Base ethernet MAC Address: 00:1d:a1:ff:49:d8
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    link auto-negotiating....
    auto-negotiation takes 10000 milli-seconds to complete
    ERROR: timeout waiting for auto-negotiation to complete
    ERROR: fail to bring ethernet link up

    The system has been encountered an error initializing
    ethernet port. You may need to check hardware
    The system is ignoring the error and continuing boot.
    If you interrupt the system boot process, the following
    commands will reinitialize ethernet, tftp, and finish
    loading the operating system software:

    ether_init
    tftp_init
    boot

    Loading "flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5"...#######################################################################################################################################################################################################################################################################################################################################################

    File "flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5" uncompressed and installed, entry point: 0x3000
    executing...
    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(7)JA5, RELEASE SOFTWARE (fc3)
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 27-Jul-07 14:03 by kehsiao
    Image text-base: 0x00003000, data-base: 0x00681A20

    Initializing flashfs...

    flashfs[1]: 137 files, 7 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 4447232
    flashfs[1]: Bytes available: 11551744
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.

    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:

    cisco AIR-LAP1242AG-N-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FOC12080P30
    PowerPCElvis CPU at 266Mhz, revision number 0x0950
    Last reset from power-on
    1 FastEthernet interface
    2 802.11 Radio(s)

    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:1D:A1:FF:49:D8
    Part Number : 73-9925-06
    PCA Assembly Number : 800-26579-05
    PCA Revision Number : A0
    PCB Serial Number : FOC12080P30
    Top Assembly Part Number : 800-29151-02
    Top Assembly Serial Number : FTX1209B29T
    Top Revision Number : A0
    Product/Model Number : AIR-LAP1242AG-N-K9
    


    Press RETURN to get started!


    *Mar 1 00:00:06.268: %DOT11-4-LOADING_RADIO: Interface Dot11Radio1, loading the radio firmware (flash:/c1240-k9w7-mx.123-7.JA5/6701.img)
    *Mar 1 00:00:07.358: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar 1 00:00:09.413: %SYS-6-LOGGERSTART: Logger process started
    *Mar 1 00:00:09.414: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar 1 00:00:10.414: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    *Mar 1 00:00:28.478: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Mar 1 00:00:28.479: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar 1 00:00:28.516: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar 1 00:00:28.540: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(7)JA5, RELEASE SOFTWARE (fc3)

    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 27-Jul-07 14:03 by kehsiao
    *Mar 1 00:00:28.540: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
    *Mar 1 00:00:29.477: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar 1 00:00:29.479: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar 1 00:00:29.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar 1 00:00:40.427: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar 1 00:00:41.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar 1 00:01:00.510: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar 1 00:01:01.510: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar 1 00:01:10.426: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar 1 00:01:11.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar 1 00:01:30.511: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar 1 00:01:31.512: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar 1 00:01:40.426: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar 1 00:01:41.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down

    -----------------------------------

    Appreciate your valuable input.

    Thanks,
    Ben.
     
    muanivanua, Jun 23, 2009
    #1
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. mpmc1@comcast.net

    Mode Switch on 1242AG

    mpmc1@comcast.net, Oct 25, 2006, in forum: Cisco
    Replies:
    1
    Views:
    411
    Brian V
    Oct 26, 2006
  2. mupp.net@gmail.com

    1242AG and WPA-PSK?

    mupp.net@gmail.com, Apr 23, 2007, in forum: Cisco
    Replies:
    1
    Views:
    967
    Aaron Leonard
    Apr 25, 2007
  3. dt1649651@yahoo.com

    1242AG and fa 0 when using vlan

    dt1649651@yahoo.com, Jul 19, 2007, in forum: Cisco
    Replies:
    3
    Views:
    1,047
    dt1649651@yahoo.com
    Jul 20, 2007
  4. roopjm
    Replies:
    0
    Views:
    418
    roopjm
    Jul 17, 2008
  5. colin
    Replies:
    0
    Views:
    517
    colin
    Jun 22, 2010
Loading...

Share This Page