Catalyst 2950 -- See log

Discussion in 'Cisco' started by Victor Cappuccio, Jun 28, 2004.

  1. Hello people I am having this output (see log) when I reboot a Catalyst 2950.
    Can anyone explain me the interpretation of this error?


    Saludos,
    Victor Cappuccio

    Switch#show logging
    Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
    Console logging: level debugging, 49 messages logged
    Monitor logging: level debugging, 0 messages logged
    Buffer logging: level debugging, 49 messages logged
    File logging: disabled
    Trap logging: level informational, 71 message lines logged

    Log Buffer (4096 bytes):
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

    00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
    S-channel operation timeout for opcode WRITE_REG_CMD
    Victor Cappuccio, Jun 28, 2004
    #1
    1. Advertising

  2. Victor Cappuccio

    Ivan Ostres Guest

    In article <>,
    says...
    > STRATA-3-SCHAN_OP_FAILURE
    >


    from CCO:

    <CCO>
    %STRATA-3-SCHAN_OP_FAILURE : \n S-channel operation timeout for opcode
    [chars]\n

    Explanation A read or writer operation to the ASIC registers or
    memories has failed. This condition was caused by due to an ASIC
    internal bus failure. This condition prevents the switch from being used
    correctly. If this message occurs extensively on the switch, it could be
    caused by an ASIC or hardware failure.

    Recommended Action Replace the ASIC.
    </CCO>

    -Ivan.
    Ivan Ostres, Jun 29, 2004
    #2
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Brian
    Replies:
    1
    Views:
    14,203
    farmerc
    Nov 7, 2007
  2. Replies:
    1
    Views:
    474
    Tim Tran
    Jul 20, 2003
  3. Rick

    Multicast on Catalyst 2950

    Rick, Jul 24, 2003, in forum: Cisco
    Replies:
    2
    Views:
    4,370
    Azure¢Ç
    Jul 25, 2003
  4. Tacobell
    Replies:
    5
    Views:
    4,239
  5. Neddy
    Replies:
    8
    Views:
    1,662
    Doug McIntyre
    May 27, 2009
Loading...

Share This Page