cant get commands under "router eigrp #" to work?

Discussion in 'Cisco' started by Scott Townsend, Jun 9, 2005.

  1. I'm trying add the following commands to my router and its not liking the
    commands under the "router eigrp 2" command.

    router eigrp 2
    network 10.0.0.0
    default-metric 1000 100 255 1 1500
    no auto-summary

    I get the Following:
    donner.sf-ts(config)# router eigrp 2
    donner.sf-ts(config)# network 10.0.0.0
    ^
    % Invalid input detected at '^' marker. (it points to the 'w' in network)


    Works fine on my 11.2 router.... Any Ideas

    Here is the "Show Version" on my router...


    Cisco Internetwork Operating System Software
    IOS (tm) 2500 Software (C2500-IK8OS-L), Version 12.2(13), RELEASE SOFTWARE
    (fc1)
    Copyright (c) 1986-2002 by cisco Systems, Inc.
    Compiled Tue 19-Nov-02 21:07 by pwade
    Image text-base: 0x0306FD38, data-base: 0x00001000

    ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
    BOOTLDR: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE
    SOFTWA)

    donner.sf-ts uptime is 1 hour, 29 minutes
    System returned to ROM by reload
    System image file is "flash:c2500-ik8os-l.122-13.bin"

    cisco 2500 (68030) processor (revision L) with 14336K/2048K bytes of memory.
    Processor board ID 02053789, with hardware revision 00000000
    Bridging software.
    X.25 software, Version 3.0.0.
    2 Ethernet/IEEE 802.3 interface(s)
    2 Serial network interface(s)
    32K bytes of non-volatile configuration memory.
    16384K bytes of processor board System flash (Read ONLY)

    Configuration register is 0x2102
     
    Scott Townsend, Jun 9, 2005
    #1
    1. Advertising

  2. Scott Townsend

    David West Guest

    Once you start eigrp with the "router eigrp 2" command, the prompt
    should change to config-rtr. Since it's not doing that, I'm guessing
    routing is not enabled on that router, look for "no ip routing"
    somewhere....an "ip routing" should fix you.

    -DW


    Scott Townsend wrote:
    > I'm trying add the following commands to my router and its not liking the
    > commands under the "router eigrp 2" command.
    >
    > router eigrp 2
    > network 10.0.0.0
    > default-metric 1000 100 255 1 1500
    > no auto-summary
    >
    > I get the Following:
    > donner.sf-ts(config)# router eigrp 2
    > donner.sf-ts(config)# network 10.0.0.0
    > ^
    > % Invalid input detected at '^' marker. (it points to the 'w' in network)
    >
    >
    > Works fine on my 11.2 router.... Any Ideas
    >
    > Here is the "Show Version" on my router...
    >
    >
    > Cisco Internetwork Operating System Software
    > IOS (tm) 2500 Software (C2500-IK8OS-L), Version 12.2(13), RELEASE SOFTWARE
    > (fc1)
    > Copyright (c) 1986-2002 by cisco Systems, Inc.
    > Compiled Tue 19-Nov-02 21:07 by pwade
    > Image text-base: 0x0306FD38, data-base: 0x00001000
    >
    > ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
    > BOOTLDR: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE
    > SOFTWA)
    >
    > donner.sf-ts uptime is 1 hour, 29 minutes
    > System returned to ROM by reload
    > System image file is "flash:c2500-ik8os-l.122-13.bin"
    >
    > cisco 2500 (68030) processor (revision L) with 14336K/2048K bytes of memory.
    > Processor board ID 02053789, with hardware revision 00000000
    > Bridging software.
    > X.25 software, Version 3.0.0.
    > 2 Ethernet/IEEE 802.3 interface(s)
    > 2 Serial network interface(s)
    > 32K bytes of non-volatile configuration memory.
    > 16384K bytes of processor board System flash (Read ONLY)
    >
    > Configuration register is 0x2102
    >
    >
     
    David West, Jun 9, 2005
    #2
    1. Advertising

  3. Ah... bliss...

    Thank you!

    Not sure why routing was turned off. It is a Dual Ethernet and was last
    routing between DSL, local LAN and a Serial Link... Maybe since I was using
    NAT I had it off.

    Thanks again,
    Scott<-
    "David West" <> wrote in message
    news:yQ_pe.120$fV.73@okepread06...
    > Once you start eigrp with the "router eigrp 2" command, the prompt should
    > change to config-rtr. Since it's not doing that, I'm guessing routing is
    > not enabled on that router, look for "no ip routing" somewhere....an "ip
    > routing" should fix you.
    >
    > -DW
    >
    >
    > Scott Townsend wrote:
    >> I'm trying add the following commands to my router and its not liking the
    >> commands under the "router eigrp 2" command.
    >>
    >> router eigrp 2
    >> network 10.0.0.0
    >> default-metric 1000 100 255 1 1500
    >> no auto-summary
    >>
    >> I get the Following:
    >> donner.sf-ts(config)# router eigrp 2
    >> donner.sf-ts(config)# network 10.0.0.0
    >> ^
    >> % Invalid input detected at '^' marker. (it points to the 'w' in network)
    >>
    >>
    >> Works fine on my 11.2 router.... Any Ideas
    >>
    >> Here is the "Show Version" on my router...
    >>
    >>
    >> Cisco Internetwork Operating System Software
    >> IOS (tm) 2500 Software (C2500-IK8OS-L), Version 12.2(13), RELEASE
    >> SOFTWARE (fc1)
    >> Copyright (c) 1986-2002 by cisco Systems, Inc.
    >> Compiled Tue 19-Nov-02 21:07 by pwade
    >> Image text-base: 0x0306FD38, data-base: 0x00001000
    >>
    >> ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
    >> BOOTLDR: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE
    >> SOFTWA)
    >>
    >> donner.sf-ts uptime is 1 hour, 29 minutes
    >> System returned to ROM by reload
    >> System image file is "flash:c2500-ik8os-l.122-13.bin"
    >>
    >> cisco 2500 (68030) processor (revision L) with 14336K/2048K bytes of
    >> memory.
    >> Processor board ID 02053789, with hardware revision 00000000
    >> Bridging software.
    >> X.25 software, Version 3.0.0.
    >> 2 Ethernet/IEEE 802.3 interface(s)
    >> 2 Serial network interface(s)
    >> 32K bytes of non-volatile configuration memory.
    >> 16384K bytes of processor board System flash (Read ONLY)
    >>
    >> Configuration register is 0x2102
    >>
     
    Scott Townsend, Jun 9, 2005
    #3
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Nibly
    Replies:
    6
    Views:
    16,102
    Walter Roberson
    Feb 22, 2005
  2. Mr Cisco Man

    cant run commands

    Mr Cisco Man, May 28, 2005, in forum: Cisco
    Replies:
    1
    Views:
    418
    Guest
    May 28, 2005
  3. unclejesse01

    man i cant belive i cant get help please

    unclejesse01, Apr 9, 2005, in forum: DVD Video
    Replies:
    2
    Views:
    411
    Bill Vermillion
    Apr 14, 2005
  4. MDesigns

    CANT GET DUAL MONITORS TO WORK WITH NEW SYSTEM

    MDesigns, Jan 6, 2004, in forum: Computer Information
    Replies:
    3
    Views:
    546
    Night_Seer
    Jan 6, 2004
  5. John Navas

    PSE6: Work-around when Help doesn't work under Windows

    John Navas, Jan 12, 2008, in forum: Digital Photography
    Replies:
    3
    Views:
    480
    John Navas
    Jan 14, 2008
Loading...

Share This Page