AP1121G - can't set to autonomous

Discussion in 'Cisco' started by Dmitry Melekhov, Oct 13, 2008.

  1. Hello!

    We bought WLC-2106 and two AP-1121G.

    AP-1121G was with autonomous software, so I downloaded software and
    switched it to
    lightweight mode, but it doesn't work.
    I see in controller log :
    *Oct 13 09:43:35.437: %LWAPP-6-DISC_RESPONSE_SENT: spam_lrad.c:1327
    Discovery Response sent successfully to AP 00:21:55:74:af:82
    *Oct 13 09:43:28.916: %DHCP-6-SCOPE_NOT_FOUND: dhcpd.c:167 Dropping
    packet from 192.168.22.18 (unable to match to a dhcp scope)
    *Oct 13 09:43:28.915: %DHCP-6-SCOPE_NOT_FOUND: dhcpd.c:167 Dropping
    packet from 192.168.22.18 (unable to match to a dhcp scope)

    Then AP reboots.

    192.168.22.18- management interface address.

    dhcp.conf for AP:

    option space ciscoap;
    option ciscoap.vci code 43 = text;
    option ciscoap.wcip code 60 = string;

    host ap {
    hardware ethernet 00:21:55:74:af:82;
    fixed-address 192.168.22.20;
    option ciscoap.vci "VCI string" ;
    option ciscoap.wcip C0:A8:16:12;
    }


    So I decided to return AP to autonomous mode.
    I downloaded image, put it on ftp.
    AP got it, rebooted, but seems it is still in lightweight mode- I see
    the same messages on controller log and can't reach AP over http.

    Could you tell me how can I
    return AP to authonomous mode?

    Is there any howto for adding AP to wlc2106?


    thank you!
     
    Dmitry Melekhov, Oct 13, 2008
    #1
    1. Advertising

  2. Hello!

    I returned AP to autonomous mode- problem was in Cisco's way to work
    with tftp- it downloads not from 10.0.0.2 , but from broadcast
    address!

    Then I converted AP to lightweght mode again.
    And still have the same problem.

    btw, it is very strange that I can't ping ap_management interface.
    Is it normal?


    On 13 ÏËÔ, 15:07, Dmitry Melekhov <> wrote:
    > Hello!
    >
    > We bought šWLC-2106 and two AP-1121G.
    >
    > AP-1121G was with autonomous software, so I downloaded software and
    > switched it to
    > šlightweight mode, but it doesn't work.
    > I see in controller log :
    > *Oct 13 09:43:35.437: %LWAPP-6-DISC_RESPONSE_SENT: spam_lrad.c:1327
    > Discovery Response sent successfully to AP 00:21:55:74:af:82
    > *Oct 13 09:43:28.916: %DHCP-6-SCOPE_NOT_FOUND: dhcpd.c:167 Dropping
    > packet from 192.168.22.18 (unable to match to a dhcp scope)
    > *Oct 13 09:43:28.915: %DHCP-6-SCOPE_NOT_FOUND: dhcpd.c:167 Dropping
    > packet from 192.168.22.18 (unable to match to a dhcp scope)
    >
    > Then AP reboots.
    >
    > 192.168.22.18- management interface address.
    >
    > dhcp.conf for AP:
    >
    > š š option space ciscoap;
    > š š option ciscoap.vci code 43 = text;
    > š š option ciscoap.wcip code 60 = string;
    >
    > host ap {
    > š š š š š š š š hardware ethernet 00:21:55:74:af:82;
    > š š š š š š š š fixed-address š192.168.22.20;
    > š š š š š š š š option ciscoap.vci "VCI string" ;
    > š š š š š š š š option ciscoap.wcip šC0:A8:16:12;
    >
    > }
    >
    > So I decided to return AP to autonomous mode.
    > I downloaded image, put it on ftp.
    > AP got it, rebooted, but seems it is still in lightweight mode- I see
    > the same messages on controller log and can't reach AP over http.
    >
    > Could you tell me how can I
    > return AP to authonomous mode?
    >
     
    Dmitry Melekhov, Oct 14, 2008
    #2
    1. Advertising

  3. Hello!

    btw, could somebody tell me why AP doesn't send join request?
    All I see in log is discovery request and reply:



    Tue Oct 14 08:12:26 2008: 00:21:55:74:af:82 Received LWAPP DISCOVERY
    REQUEST from AP 00:21:55:74:af:82 to ff:ff:ff:ff:ff:ff on port '1'
    Tue Oct 14 08:12:26 2008: Start of Packet
    Tue Oct 14 08:12:26 2008: Ethernet Source MAC (LRAD):
    00:21:55:74:AF:82
    Tue Oct 14 08:12:26 2008: Msg Type :
    Tue Oct 14 08:12:26 2008: DISCOVERY_REQUEST
    Tue Oct 14 08:12:26 2008: Msg Length : 21
    Tue Oct 14 08:12:26 2008: Msg SeqNum : 0
    Tue Oct 14 08:12:26 2008:
    IE : UNKNOWN IE 58
    Tue Oct 14 08:12:26 2008: IE Length : 1
    Tue Oct 14 08:12:26 2008: Decode routine not available, Printing Hex
    Dump
    Tue Oct 14 08:12:26 2008: 00000000:
    00 .
    Tue Oct 14 08:12:26 2008:
    IE : RAD_PAYLOAD
    Tue Oct 14 08:12:26 2008: IE Length : 14
    Tue Oct 14 08:12:26 2008: H/W Version : 1
    Tue Oct 14 08:12:26 2008: H/W Release : 0
    Tue Oct 14 08:12:26 2008: H/W Maint : 0
    Tue Oct 14 08:12:26 2008: H/W Build : 0
    Tue Oct 14 08:12:26 2008: S/W Version : 3
    Tue Oct 14 08:12:26 2008: S/W Release : 0
    Tue Oct 14 08:12:26 2008: S/W Maint : 51
    Tue Oct 14 08:12:26 2008: S/W Build : 0
    Tue Oct 14 08:12:26 2008: Boot Version : 12
    Tue Oct 14 08:12:26 2008: Boot Release : 3
    Tue Oct 14 08:12:26 2008: Boot Maint : 2
    Tue Oct 14 08:12:26 2008: Boot Build : 4
    Tue Oct 14 08:12:26 2008: numSlots : 0
    Tue Oct 14 08:12:26 2008: numFilledSlots : 0
    Tue Oct 14 08:12:26 2008: End of Packet
    Tue Oct 14 08:12:26 2008: Start of Packet
    Tue Oct 14 08:12:26 2008: Ethernet Destination MAC (LRAD):
    00:21:55:74:AF:82
    Tue Oct 14 08:12:26 2008: Msg Type :
    Tue Oct 14 08:12:26 2008: DISCOVERY_REPLY
    Tue Oct 14 08:12:26 2008: Msg Length : 39
    Tue Oct 14 08:12:26 2008: Msg SeqNum : 0
    Tue Oct 14 08:12:26 2008:
    IE : MWAR_PAYLOAD
    Tue Oct 14 08:12:26 2008: IE Length : 17
    Tue Oct 14 08:12:26 2008: Mwar Type :
    SPAM_MASTER_MWAR
    Tue Oct 14 08:12:26 2008: H/W Version : 1
    Tue Oct 14 08:12:26 2008: H/W Release : 0
    Tue Oct 14 08:12:26 2008: H/W Maint : 0
    Tue Oct 14 08:12:26 2008: H/W Build : 1
    Tue Oct 14 08:12:26 2008: S/W Version : 4
    Tue Oct 14 08:12:26 2008: S/W Release : 2
    Tue Oct 14 08:12:26 2008: S/W Maint : 130
    Tue Oct 14 08:12:26 2008: S/W Build : 0
    Tue Oct 14 08:12:26 2008: Number of Active MS : 100
    Tue Oct 14 08:12:26 2008: Number of Supported MS : 1000
    Tue Oct 14 08:12:26 2008: Number of Active RAD's : 0
    Tue Oct 14 08:12:26 2008: Number of Supported RADs: 6
    Tue Oct 14 08:12:26 2008:
    IE : MWAR_NAME_PAYLOAD
    Tue Oct 14 08:12:26 2008: IE Length : 7
    Tue Oct 14 08:12:26 2008: MWAR Name :
    Tue Oct 14 08:12:26 2008: WCL2106
    Tue Oct 14 08:12:26 2008:
    IE : UNKNOWN IE 99
    Tue Oct 14 08:12:26 2008: IE Length : 6
    Tue Oct 14 08:12:26 2008: Decode routine not available, Printing Hex
    Dump
    Tue Oct 14 08:12:26 2008: 00000000: c0 a8 16 13 00
    00 ......
    Tue Oct 14 08:12:26 2008: End of Packet
    Tue Oct 14 08:12:26 2008: 00:21:55:74:af:82 Successful transmission of
    LWAPP Discovery Response to AP 00:21:55:74:af:82 on port 1
    Tue Oct 14 08:13:54 2008: 00:21:55:74:af:82 Received LWAPP DISCOVERY
    REQUEST from AP 00:21:55:74:af:82 to ff:ff:ff:ff:ff:ff on port '1'
    Tue Oct 14 08:13:54 2008: Start of Packet
    Tue Oct 14 08:13:54 2008: Ethernet Source MAC (LRAD):
    00:21:55:74:AF:82
    Tue Oct 14 08:13:54 2008: Msg Type :
    Tue Oct 14 08:13:54 2008: DISCOVERY_REQUEST
    Tue Oct 14 08:13:54 2008: Msg Length : 21
    Tue Oct 14 08:13:54 2008: Msg SeqNum : 0
    Tue Oct 14 08:13:54 2008:
    IE : UNKNOWN IE 58
    Tue Oct 14 08:13:54 2008: IE Length : 1
    Tue Oct 14 08:13:54 2008: Decode routine not available, Printing Hex
    Dump
    Tue Oct 14 08:13:54 2008: 00000000:
    00 .
    Tue Oct 14 08:13:54 2008:
    IE : RAD_PAYLOAD
    Tue Oct 14 08:13:54 2008: IE Length : 14
    Tue Oct 14 08:13:54 2008: H/W Version : 1
    Tue Oct 14 08:13:54 2008: H/W Release : 0
    Tue Oct 14 08:13:54 2008: H/W Maint : 0
    Tue Oct 14 08:13:54 2008: H/W Build : 0
    Tue Oct 14 08:13:54 2008: S/W Version : 3
    Tue Oct 14 08:13:54 2008: S/W Release : 0
    Tue Oct 14 08:13:54 2008: S/W Maint : 51
    Tue Oct 14 08:13:54 2008: S/W Build : 0
    Tue Oct 14 08:13:54 2008: Boot Version : 12
    Tue Oct 14 08:13:54 2008: Boot Release : 3
    Tue Oct 14 08:13:54 2008: Boot Maint : 2
    Tue Oct 14 08:13:54 2008: Boot Build : 4
    Tue Oct 14 08:13:54 2008: numSlots : 0
    Tue Oct 14 08:13:54 2008: numFilledSlots : 0
    Tue Oct 14 08:13:54 2008: End of Packet
    Tue Oct 14 08:13:54 2008: Start of Packet
    Tue Oct 14 08:13:54 2008: Ethernet Destination MAC (LRAD):
    00:21:55:74:AF:82
    Tue Oct 14 08:13:54 2008: Msg Type :
    Tue Oct 14 08:13:54 2008: DISCOVERY_REPLY
    Tue Oct 14 08:13:54 2008: Msg Length : 39
    Tue Oct 14 08:13:54 2008: Msg SeqNum : 0
    Tue Oct 14 08:13:54 2008:
    IE : MWAR_PAYLOAD
    Tue Oct 14 08:13:54 2008: IE Length : 17
    Tue Oct 14 08:13:54 2008: Mwar Type :
    SPAM_MASTER_MWAR
    Tue Oct 14 08:13:54 2008: H/W Version : 1
    Tue Oct 14 08:13:54 2008: H/W Release : 0
    Tue Oct 14 08:13:54 2008: H/W Maint : 0
    Tue Oct 14 08:13:54 2008: H/W Build : 1
    Tue Oct 14 08:13:54 2008: S/W Version : 4
    Tue Oct 14 08:13:54 2008: S/W Release : 2
    Tue Oct 14 08:13:54 2008: S/W Maint : 130
    Tue Oct 14 08:13:54 2008: S/W Build : 0
    Tue Oct 14 08:13:54 2008: Number of Active MS : 100
    Tue Oct 14 08:13:54 2008: Number of Supported MS : 1000
    Tue Oct 14 08:13:54 2008: Number of Active RAD's : 0
    Tue Oct 14 08:13:54 2008: Number of Supported RADs: 6
    Tue Oct 14 08:13:54 2008:
    IE : MWAR_NAME_PAYLOAD
    Tue Oct 14 08:13:54 2008: IE Length : 7
    Tue Oct 14 08:13:54 2008: MWAR Name :
    Tue Oct 14 08:13:54 2008: WLC2106
    Tue Oct 14 08:13:54 2008:
    IE : UNKNOWN IE 99
    Tue Oct 14 08:13:54 2008: IE Length : 6
    Tue Oct 14 08:13:54 2008: Decode routine not available, Printing Hex
    Dump
    Tue Oct 14 08:13:54 2008: 00000000: c0 a8 16 13 00
    00 ......
    Tue Oct 14 08:13:54 2008: End of Packet
    Tue Oct 14 08:13:54 2008: 00:21:55:74:af:82 Successful transmission of
    LWAPP Discovery Response to AP 00:21:55:74:af:82 on port 1
     
    Dmitry Melekhov, Oct 14, 2008
    #3
  4. On Oct 14, 3:01 pm, "PrzemekD" <>
    wrote:
    > Uzytkownik "Dmitry Melekhov" <> napisal w wiadomoscinews:...
    >
    > > Hello!

    >
    > > We bought WLC-2106 and twoAP-1121G.

    >
    > >AP-1121Gwas with autonomous software, so I downloaded software and
    > >[...]
    > > Is there any howto for adding AP to wlc2106?

    >
    > > thank you!

    >
    > Hallo
    >
    > I had similar problem witch 4402 controller & 1242
    >
    > The solution was to switch to Layer 3 mode instead of layer 2.
    >
    > Those APs (1121, 1242,13xx) does not support layer2 lightweight mode.


    Hello!

    Unfortunately, my 2106 supports only l3 mode and AP-1121G can't join
    to 2106 :-(
     
    Dmitry Melekhov, Oct 22, 2008
    #4
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Patrick Colbeck

    Meging two BGP autonomous systems

    Patrick Colbeck, Nov 26, 2003, in forum: Cisco
    Replies:
    2
    Views:
    534
    Barry Margolin
    Dec 5, 2003
  2. Isis
    Replies:
    0
    Views:
    610
  3. Replies:
    11
    Views:
    754
  4. jimbo
    Replies:
    5
    Views:
    14,449
    =?ISO-8859-1?Q?Axel_G=E4rtner?=
    Jul 13, 2005
  5. morales
    Replies:
    1
    Views:
    772
    morales
    Mar 25, 2009
Loading...

Share This Page