6509 Booting in rommon

Discussion in 'Cisco' started by JC, May 2, 2005.

  1. JC

    JC Guest

    I asked this a few months back but got called off to another site. So
    here is some more information. The unit always goes into rommon mode
    when it is powered down and back up. Here is what is going on.

    System Bootstrap, Version 6.1(3)
    Copyright (c) 1994-2000 by cisco Systems, Inc.

    Testing lower main memory - data equals address
    Testing lower main memory - checkerboard
    Testing lower main memory - inverse checkerboard
    Clearing lower 16K memory for cache initialization
    Clearing bss
    Reading monitor variables from NVRAM
    Warning: Rommon NVRAM area is corrupted. Initialize the area to default
    values

    Enabling interrupts
    Initializing TLB
    Initializing cache
    Initializing required TLB entries
    Initializing main memory
    Sizing NVRAM
    Initializing PCMCIA controller
    Exiting init
    c6k_sup2 processor with 131072 Kbytes of main memory

    rommon 1 > sh mod

    monitor: command "sh" not found
    rommon 2 > boot

    Self decompressing the image :
    ############################################################################################################################################]

    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco Internetwork Operating System Software
    IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Sat 25-Oct-03 09:55 by hqluong
    Image text-base: 0x40020F90, data-base: 0x40978000


    00:00:02: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
    00:00:03: %OIR-6-CONSOLE: Changing console ownership to route processor



    System Bootstrap, Version 12.1(3r)E2, RELEASE SOFTWARE (fc1)
    Copyright (c) 2000 by cisco Systems, Inc.
    Cat6k-MSFC2 platform with 131072 Kbytes of main memory

    Download Start
    !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    Download Completed! Booting the image.
    Self decompressing the image :
    ############################################################################################################################################]

    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco Internetwork Operating System Software
    IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Sat 25-Oct-03 09:18 by hqluong
    Image text-base: 0x40008F90, data-base: 0x4184E000

    cisco WS-C6509 (R7000) processor (revision 1.0) with 112640K/18432K
    bytes of memory.
    Processor board ID SCA0318003V
    R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3
    Cache
    Last reset from power-on
    X.25 software, Version 3.0.0.
    Bridging software.
    1 Virtual Ethernet/IEEE 802.3 interface(s)
    48 FastEthernet/IEEE 802.3 interface(s)
    2 Gigabit Ethernet/IEEE 802.3 interface(s)
    381K bytes of non-volatile configuration memory.

    16384K bytes of Flash internal SIMM (Sector size 512K).
    %Error opening tftp://255.255.255.255/network-confg (Socket error)
    %Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
    SETUP: new interface Vlan1 placed in "shutdown" state
    SETUP: new interface GigabitEthernet1/1 placed in "shutdown" state
    SETUP: new interface GigabitEthernet1/2 placed in "shutdown" state
    SETUP: new interface FastEthernet4/1 placed in "shutdown" state
    SETUP: new interface FastEthernet4/2 placed in "shutdown" state
    SETUP: new interface FastEthernet4/3 placed in "shutdown" state
    SETUP: new interface FastEthernet4/4 placed in "shutdown" state
    SETUP: new interface FastEthernet4/5 placed in "shutdown" state
    SETUP: new interface FastEthernet4/6 placed in "shutdown" state
    SETUP: new interface FastEthernet4/7 placed in "shutdown" state
    SETUP: new interface FastEthernet4/8 placed in "shutdown" state
    SETUP: new interface FastEthernet4/9 placed in "shutdown" state
    SETUP: new interface FastEthernet4/10 placed in "shutdown" state
    SETUP: new interface FastEthernet4/11 placed in "shutdown" state
    SETUP: new interface FastEthernet4/12 placed in "shutdown" state
    SETUP: new interface FastEthernet4/13 placed in "shutdown" state
    SETUP: new interface FastEthernet4/14 placed in "shutdown" state
    SETUP: new interface FastEthernet4/15 placed in "shutdown" state
    SETUP: new interface FastEthernet4/16 placed in "shutdown" state
    SETUP: new interface FastEthernet4/17 placed in "shutdown" state
    SETUP: new interface FastEthernet4/18 placed in "shutdown" state
    SETUP: new interface FastEthernet4/19 placed in "shutdown" state
    SETUP: new interface FastEthernet4/20 placed in "shutdown" state
    SETUP: new interface FastEthernet4/21 placed in "shutdown" state
    SETUP: new interface FastEthernet4/22 placed in "shutdown" state
    SETUP: new interface FastEthernet4/23 placed in "shutdown" state
    SETUP: new interface FastEthernet4/24 placed in "shutdown" state
    SETUP: new interface FastEthernet4/25 placed in "shutdown" state
    SETUP: new interface FastEthernet4/26 placed in "shutdown" state
    SETUP: new interface FastEthernet4/27 placed in "shutdown" state
    SETUP: new interface FastEthernet4/28 placed in "shutdown" state
    SETUP: new interface FastEthernet4/29 placed in "shutdown" state
    SETUP: new interface FastEthernet4/30 placed in "shutdown" state
    SETUP: new interface FastEthernet4/31 placed in "shutdown" state
    SETUP: new interface FastEthernet4/32 placed in "shutdown" state
    SETUP: new interface FastEthernet4/33 placed in "shutdown" state
    SETUP: new interface FastEthernet4/34 placed in "shutdown" state
    SETUP: new interface FastEthernet4/35 placed in "shutdown" state
    SETUP: new interface FastEthernet4/36 placed in "shutdown" state
    SETUP: new interface FastEthernet4/37 placed in "shutdown" state
    SETUP: new interface FastEthernet4/38 placed in "shutdown" state
    SETUP: new interface FastEthernet4/39 placed in "shutdown" state
    SETUP: new interface FastEthernet4/40 placed in "shutdown" state
    SETUP: new interface FastEthernet4/41 placed in "shutdown" state
    SETUP: new interface FastEthernet4/42 placed in "shutdown" state
    SETUP: new interface FastEthernet4/43 placed in "shutdown" state
    SETUP: new interface FastEthernet4/44 placed in "shutdown" state
    SETUP: new interface FastEthernet4/45 placed in "shutdown" state
    SETUP: new interface FastEthernet4/46 placed in "shutdown" state
    SETUP: new interface FastEthernet4/47 placed in "shutdown" state
    SETUP: new interface FastEthernet4/48 placed in "shutdown" state


    Press RETURN to get started!


    00:00:33: RP: Currently running ROMMON from S (Gold) region
    00:01:02: %SYS-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software
    IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Sat 25-Oct-03 09:18 by hqluong
    00:00:37: SP: SP: Currently running ROMMON from S (Gold) region
    00:00:39: %C6K_PLATFORM-SP-4-CONFREG_BREAK_ENABLED: The default factory
    setting for config register is 0x2102.It is advisable to retain 1 in
    0x2102 as it prevents returnin.

    00:01:02: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a
    cold start
    00:01:02: %SYS-6-BOOTTIME: Time taken to reboot after reload = 445
    seconds
    00:01:01: %SYS-SP-5-RESTART: System restarted --
    Cisco Internetwork Operating System Software
    IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Sat 25-Oct-03 09:55 by hqluong
    00:01:03: %OIR-SP-6-INSPS: Power supply inserted in slot 1
    00:01:03: %OIR-SP-6-INSPS: Power supply inserted in slot 2
    00:01:03: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
    00:01:05: %C6KENV-SP-4-PSFANFAILED: the fan in power supply 1 has
    failed
    00:01:16: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimum Online
    Diagnostics...
    00:01:20: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
    00:01:20: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are
    now online
    00:01:35: %DIAG-SP-6-RUN_MINIMUM: Module 4: Running Minimum Online
    Diagnostics...
    00:01:44: %DIAG-SP-6-DIAG_OK: Module 4: Passed Online Diagnostics
    00:01:44: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are
    now online
    Router>sh mod
    Mod Ports Card Type Model
    Serial No.
    --- ----- -------------------------------------- ------------------
    -----------
    1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE
    SAD050707ZU
    4 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45
    SAL05084X6T

    Mod MAC addresses Hw Fw Sw
    Status
    --- ---------------------------------- ------ ------------ ------------
    -------
    1 0004.c0f8.9e76 to 0004.c0f8.9e77 2.2 6.1(3) 12.1(20)E
    Ok
    4 0004.de61.f760 to 0004.de61.f78f 2.0 5.4(2) 8.2(0.58)TFW
    Ok

    Mod Sub-Module Model Serial Hw
    Status
    --- --------------------------- --------------- --------------- -------
    -------
    1 Policy Feature Card 2 WS-F6K-PFC2 SAD05080T6L 1.3
    Ok
    1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05080KHG 1.2
    Ok

    Mod Online Diag Status
    --- -------------------
    1 Pass
    4 Pass
    Router>
    JC, May 2, 2005
    #1
    1. Advertising

  2. JC

    Nick Guest

    Check the following

    http://www.cisco.com/en/US/customer...0/products_field_notice09186a0080231f74.shtml

    JC wrote:
    > I asked this a few months back but got called off to another site. So
    > here is some more information. The unit always goes into rommon mode
    > when it is powered down and back up. Here is what is going on.
    >
    > System Bootstrap, Version 6.1(3)
    > Copyright (c) 1994-2000 by cisco Systems, Inc.
    >
    > Testing lower main memory - data equals address
    > Testing lower main memory - checkerboard
    > Testing lower main memory - inverse checkerboard
    > Clearing lower 16K memory for cache initialization
    > Clearing bss
    > Reading monitor variables from NVRAM
    > Warning: Rommon NVRAM area is corrupted. Initialize the area to default
    > values
    >
    > Enabling interrupts
    > Initializing TLB
    > Initializing cache
    > Initializing required TLB entries
    > Initializing main memory
    > Sizing NVRAM
    > Initializing PCMCIA controller
    > Exiting init
    > c6k_sup2 processor with 131072 Kbytes of main memory
    >
    > rommon 1 > sh mod
    >
    > monitor: command "sh" not found
    > rommon 2 > boot
    >
    > Self decompressing the image :
    > ############################################################################################################################################]
    >
    > Restricted Rights Legend
    >
    > Use, duplication, or disclosure by the Government is
    > subject to restrictions as set forth in subparagraph
    > (c) of the Commercial Computer Software - Restricted
    > Rights clause at FAR sec. 52.227-19 and subparagraph
    > (c) (1) (ii) of the Rights in Technical Data and Computer
    > Software clause at DFARS sec. 252.227-7013.
    >
    > cisco Systems, Inc.
    > 170 West Tasman Drive
    > San Jose, California 95134-1706
    >
    >
    >
    > Cisco Internetwork Operating System Software
    > IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    > DEPLOYMENT RELEASE SOFTWARE (fc1)
    > TAC Support: http://www.cisco.com/tac
    > Copyright (c) 1986-2003 by cisco Systems, Inc.
    > Compiled Sat 25-Oct-03 09:55 by hqluong
    > Image text-base: 0x40020F90, data-base: 0x40978000
    >
    >
    > 00:00:02: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
    > 00:00:03: %OIR-6-CONSOLE: Changing console ownership to route processor
    >
    >
    >
    > System Bootstrap, Version 12.1(3r)E2, RELEASE SOFTWARE (fc1)
    > Copyright (c) 2000 by cisco Systems, Inc.
    > Cat6k-MSFC2 platform with 131072 Kbytes of main memory
    >
    > Download Start
    > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    > Download Completed! Booting the image.
    > Self decompressing the image :
    > ############################################################################################################################################]
    >
    > Restricted Rights Legend
    >
    > Use, duplication, or disclosure by the Government is
    > subject to restrictions as set forth in subparagraph
    > (c) of the Commercial Computer Software - Restricted
    > Rights clause at FAR sec. 52.227-19 and subparagraph
    > (c) (1) (ii) of the Rights in Technical Data and Computer
    > Software clause at DFARS sec. 252.227-7013.
    >
    > cisco Systems, Inc.
    > 170 West Tasman Drive
    > San Jose, California 95134-1706
    >
    >
    >
    > Cisco Internetwork Operating System Software
    > IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(20)E, EARLY
    > DEPLOYMENT RELEASE SOFTWARE (fc1)
    > TAC Support: http://www.cisco.com/tac
    > Copyright (c) 1986-2003 by cisco Systems, Inc.
    > Compiled Sat 25-Oct-03 09:18 by hqluong
    > Image text-base: 0x40008F90, data-base: 0x4184E000
    >
    > cisco WS-C6509 (R7000) processor (revision 1.0) with 112640K/18432K
    > bytes of memory.
    > Processor board ID SCA0318003V
    > R7000 CPU at 300Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3
    > Cache
    > Last reset from power-on
    > X.25 software, Version 3.0.0.
    > Bridging software.
    > 1 Virtual Ethernet/IEEE 802.3 interface(s)
    > 48 FastEthernet/IEEE 802.3 interface(s)
    > 2 Gigabit Ethernet/IEEE 802.3 interface(s)
    > 381K bytes of non-volatile configuration memory.
    >
    > 16384K bytes of Flash internal SIMM (Sector size 512K).
    > %Error opening tftp://255.255.255.255/network-confg (Socket error)
    > %Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
    > SETUP: new interface Vlan1 placed in "shutdown" state
    > SETUP: new interface GigabitEthernet1/1 placed in "shutdown" state
    > SETUP: new interface GigabitEthernet1/2 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/1 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/2 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/3 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/4 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/5 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/6 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/7 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/8 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/9 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/10 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/11 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/12 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/13 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/14 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/15 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/16 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/17 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/18 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/19 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/20 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/21 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/22 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/23 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/24 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/25 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/26 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/27 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/28 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/29 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/30 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/31 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/32 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/33 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/34 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/35 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/36 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/37 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/38 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/39 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/40 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/41 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/42 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/43 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/44 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/45 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/46 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/47 placed in "shutdown" state
    > SETUP: new interface FastEthernet4/48 placed in "shutdown" state
    >
    >
    > Press RETURN to get started!
    >
    >
    > 00:00:33: RP: Currently running ROMMON from S (Gold) region
    > 00:01:02: %SYS-5-RESTART: System restarted --
    > Cisco Internetwork Operating System Software
    > IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(20)E, EARLY
    > DEPLOYMENT RELEASE SOFTWARE (fc1)
    > TAC Support: http://www.cisco.com/tac
    > Copyright (c) 1986-2003 by cisco Systems, Inc.
    > Compiled Sat 25-Oct-03 09:18 by hqluong
    > 00:00:37: SP: SP: Currently running ROMMON from S (Gold) region
    > 00:00:39: %C6K_PLATFORM-SP-4-CONFREG_BREAK_ENABLED: The default factory
    > setting for config register is 0x2102.It is advisable to retain 1 in
    > 0x2102 as it prevents returnin.
    >
    > 00:01:02: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a
    > cold start
    > 00:01:02: %SYS-6-BOOTTIME: Time taken to reboot after reload = 445
    > seconds
    > 00:01:01: %SYS-SP-5-RESTART: System restarted --
    > Cisco Internetwork Operating System Software
    > IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    > DEPLOYMENT RELEASE SOFTWARE (fc1)
    > TAC Support: http://www.cisco.com/tac
    > Copyright (c) 1986-2003 by cisco Systems, Inc.
    > Compiled Sat 25-Oct-03 09:55 by hqluong
    > 00:01:03: %OIR-SP-6-INSPS: Power supply inserted in slot 1
    > 00:01:03: %OIR-SP-6-INSPS: Power supply inserted in slot 2
    > 00:01:03: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
    > 00:01:05: %C6KENV-SP-4-PSFANFAILED: the fan in power supply 1 has
    > failed
    > 00:01:16: %DIAG-SP-6-RUN_MINIMUM: Module 1: Running Minimum Online
    > Diagnostics...
    > 00:01:20: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
    > 00:01:20: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are
    > now online
    > 00:01:35: %DIAG-SP-6-RUN_MINIMUM: Module 4: Running Minimum Online
    > Diagnostics...
    > 00:01:44: %DIAG-SP-6-DIAG_OK: Module 4: Passed Online Diagnostics
    > 00:01:44: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are
    > now online
    > Router>sh mod
    > Mod Ports Card Type Model
    > Serial No.
    > --- ----- -------------------------------------- ------------------
    > -----------
    > 1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE
    > SAD050707ZU
    > 4 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45
    > SAL05084X6T
    >
    > Mod MAC addresses Hw Fw Sw
    > Status
    > --- ---------------------------------- ------ ------------ ------------
    > -------
    > 1 0004.c0f8.9e76 to 0004.c0f8.9e77 2.2 6.1(3) 12.1(20)E
    > Ok
    > 4 0004.de61.f760 to 0004.de61.f78f 2.0 5.4(2) 8.2(0.58)TFW
    > Ok
    >
    > Mod Sub-Module Model Serial Hw
    > Status
    > --- --------------------------- --------------- --------------- -------
    > -------
    > 1 Policy Feature Card 2 WS-F6K-PFC2 SAD05080T6L 1.3
    > Ok
    > 1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAD05080KHG 1.2
    > Ok
    >
    > Mod Online Diag Status
    > --- -------------------
    > 1 Pass
    > 4 Pass
    > Router>
    >
    Nick, May 2, 2005
    #2
    1. Advertising

  3. JC

    JC Guest

    That is not for the same card as what I have installed. Though it could
    be the same issue a bad crystal. I just want to rule out everything
    else.
    JC, May 2, 2005
    #3
  4. JC

    Chris Marva Guest

    "JC" <> wrote in news:1114995036.191731.74690
    @f14g2000cwb.googlegroups.com:

    > That is not for the same card as what I have installed. Though it could
    > be the same issue a bad crystal. I just want to rule out everything
    > else.
    >
    >



    We had seen this a couple of times. I assume you're using native, not
    hybrid. Once the thing is booted, do:

    sho ver to see the RP config register.

    remote command switch sho ver to see the SP config register.

    If they don't match, set them so they do match and reboot
    (at least, that is the problem that we had, the cfg regs
    were not synced).

    hope this helps,

    c
    Chris Marva, May 3, 2005
    #4
  5. JC

    Frreak Guest

    Pls post the show version...
    The default config-register value should be 0x2102... If iti s anything
    else. then this may be the reason.. or else...ur NVRAM might be
    corrupted for which u may have to contact cisco TAC......

    Cheers,
    Naveen B
    Frreak, May 4, 2005
    #5
  6. JC

    gordokan Guest

    Have you set the configuration register to the normal value of 0x2102?
    This would normally regain the correct boot sequence.
    gordokan, May 4, 2005
    #6
  7. JC

    JC Guest

    The config register is set to 0x2102.
    JC, May 5, 2005
    #7
  8. JC

    Simon Stoll Guest

    As you are using hybrid, there are two config-registers, one on the SUP and
    one on the MSFC. Both should be 0x2102. The one on the MSFC you see easily
    with "sh ver", the other on the SUP you can see with "remote command switch
    show version"

    Simon



    "JC" <> schrieb im Newsbeitrag
    news:...
    > The config register is set to 0x2102.
    >
    Simon Stoll, May 8, 2005
    #8
  9. JC

    JC Guest

    Router#remote command switch show version
    Cisco Internetwork Operating System Software
    IOS (tm) c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)
    TAC Support: http://www.cisco.com/tac
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Sat 25-Oct-03 09:55 by hqluong
    Image text-base: 0x40020F90, data-base: 0x40978000

    ROM: System Bootstrap, Version 6.1(3)
    BOOTLDR: c6sup2_sp Software (c6sup2_sp-SP-M), Version 12.1(20)E, EARLY
    DEPLOYMENT RELEASE SOFTWARE (fc1)

    Router uptime is 2 minutes
    Time since Router switched to active is 2 minutes
    System returned to ROM by error - a Software forced crash, PC
    0x401252BC at 13:12:34 UTC Mon May 2 2005
    System image file is "bootflash:c6sup22-ps-mz.121-20.E.bin"

    cisco WS-C6509 (R7000) processor (revision 1.0) with 112640K/18432K
    bytes of memory.
    Processor board ID SCA0318003V
    R7000 CPU at 250Mhz, Implementation 39, Rev 2.1, 256KB L2, 1024KB L3
    Cache
    Last reset from power-on
    X.25 software, Version 3.0.0.
    48 FastEthernet/IEEE 802.3 interface(s)
    2 Gigabit Ethernet/IEEE 802.3 interface(s)
    381K bytes of non-volatile configuration memory.

    32768K bytes of Flash internal SIMM (Sector size 512K).
    Configuration register is 0x8000
    JC, May 9, 2005
    #9
  10. JC

    JC Guest

    It has gotten to the point where my boss and I have decided to hire
    someone to look into this. So if any of you are interested contact me
    at .
    JC, May 18, 2005
    #10
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. JC

    Cisco 6509 and rommon.

    JC, Mar 6, 2005, in forum: Cisco
    Replies:
    1
    Views:
    806
  2. Uli Link
    Replies:
    4
    Views:
    11,537
    XTREM
    Aug 11, 2009
  3. sowfpote

    booting to rommon

    sowfpote, Oct 16, 2006, in forum: Cisco
    Replies:
    1
    Views:
    9,604
    srinath_7
    Oct 27, 2006
  4. 6509 Boots to Rommon

    , Oct 12, 2006, in forum: Cisco
    Replies:
    6
    Views:
    4,820
  5. Markus Sonnenberg

    Cisco 881 is booting into rommon

    Markus Sonnenberg, Jan 16, 2012, in forum: Cisco
    Replies:
    5
    Views:
    1,820
    STaylor
    Mar 22, 2013
Loading...

Share This Page