5500 module

Discussion in 'Cisco' started by ufik, Aug 6, 2007.

  1. ufik

    ufik Guest

    Hello,

    What is mean faulty status. It is hardware problem or something else.
    Is it normal status for Supervisor?

    5500> (enable) sh module
    Mod Slot Ports Module-Type Model Sub
    Status
    --- ---- ----- ------------------------- ------------------- ---
    --------
    1 1 2 1000BaseSX Supervisor WS-X5530 yes
    faulty
    2 2 Gigabit Ethernet Ext WS-X5410
    3 3 9 Gigabit Ethernet WS-X5410 no ok
    6 6 12 100BaseFX MM Ethernet WS-X5201 no ok
    7 7 1 Route Switch WS-X5302 no ok
    8 8 12 10BaseFL Ethernet WS-X5011 no ok
    9 9 12 100BaseFX MM Ethernet WS-X5111 no ok
    10 10 24 10/100BaseTX Ethernet WS-X5224 no ok
    11 11 36 10/100BaseTX Ethernet WS-X5239 no ok
    12 12 36 10/100BaseTX Ethernet WS-X5239 no ok

    Thank you for help.
    ufik, Aug 6, 2007
    #1
    1. Advertising

  2. ufik

    make Guest

    What about "show test 1" ?
    "show test diaglevel" ?
    "show system" ?


    > What is mean faulty status. It is hardware problem or something else.
    > Is it normal status for Supervisor?
    >
    > 5500> (enable) sh module
    > Mod Slot Ports Module-Type Model Sub
    > Status
    > --- ---- ----- ------------------------- ------------------- ---
    > --------
    > 1 1 2 1000BaseSX Supervisor WS-X5530 yes
    > faulty
    > 2 2 Gigabit Ethernet Ext WS-X5410
    > 3 3 9 Gigabit Ethernet WS-X5410 no ok
    > 6 6 12 100BaseFX MM Ethernet WS-X5201 no ok
    > 7 7 1 Route Switch WS-X5302 no ok
    > 8 8 12 10BaseFL Ethernet WS-X5011 no ok
    > 9 9 12 100BaseFX MM Ethernet WS-X5111 no ok
    > 10 10 24 10/100BaseTX Ethernet WS-X5224 no ok
    > 11 11 36 10/100BaseTX Ethernet WS-X5239 no ok
    > 12 12 36 10/100BaseTX Ethernet WS-X5239 no ok
    >
    > Thank you for help.
    >
    make, Aug 6, 2007
    #2
    1. Advertising

  3. ufik

    ufik Guest

    On 6 Sie, 19:45, make <> wrote:
    > What about "show test 1" ?
    > "show test diaglevel" ?
    > "show system" ?
    >
    > > What is mean faulty status. It is hardware problem or something else.
    > > Is it normal status for Supervisor?

    >
    > > 5500> (enable) sh module
    > > Mod Slot Ports Module-Type Model Sub
    > > Status
    > > --- ---- ----- ------------------------- ------------------- ---
    > > --------
    > > 1 1 2 1000BaseSX Supervisor WS-X5530 yes
    > > faulty
    > > 2 2 Gigabit Ethernet Ext WS-X5410
    > > 3 3 9 Gigabit Ethernet WS-X5410 no ok
    > > 6 6 12 100BaseFX MM Ethernet WS-X5201 no ok
    > > 7 7 1 Route Switch WS-X5302 no ok
    > > 8 8 12 10BaseFL Ethernet WS-X5011 no ok
    > > 9 9 12 100BaseFX MM Ethernet WS-X5111 no ok
    > > 10 10 24 10/100BaseTX Ethernet WS-X5224 no ok
    > > 11 11 36 10/100BaseTX Ethernet WS-X5239 no ok
    > > 12 12 36 10/100BaseTX Ethernet WS-X5239 no ok

    >
    > > Thank you for help.


    500> (enable) show test 1

    Diagnostic mode: minimal (mode at next reset: minimal)


    Module 1 : 2-port 1000BaseSX Supervisor
    Network Management Processor (NMP) Status: (. = Pass, F = Fail, U =
    Unknown)
    ROM: . Flash-EEPROM: . Ser-EEPROM: . NVRAM: . MCP Comm: .

    EARL III Status :
    DisableIndexLearnTest: .
    DontLearnTest: .
    DisableNewLearnTest: .
    ConditionalLearnTest: .
    MonitorColorFloodTest: .
    EarlTrapTest: .
    StaticMacAndTypeTest: .
    BadDvlanTest: .
    BadBpduTest: .
    IndexMatchTest: .
    ProtocolTypeTest: .
    IgmpTest: .
    SourceMissTest: .
    SourceModifiedTest: .
    ArpaToArpaShortcutTest: .
    ArpaToSnapShortcutTest: .
    SnapToArpaShortcutTest: .
    SnapToSnapShortcutTest: .
    SoftwareShortcutTest: .
    MulticastExpansionTest: .
    DontShortcutTest: .
    ShortcutTableFullTest: .
    ArpaToArpaShortcutTest(IPX): .
    ArpaToSnapShortcutTest(IPX): .
    ArpaToSapShortcutTest(IPX): .
    ArpaToRawShortcutTest(IPX): .
    SnapToArpaShortcutTest(IPX): .
    SnapToSnapShortcutTest(IPX): .
    SnapToSapShortcutTest(IPX): .
    SapToArpaShortcutTest(IPX): .
    SapToSnapShortcutTest(IPX): .
    SapToSapShortcutTest(IPX): .
    SapToRawShortcutTest(IPX): .
    RawToArpaShortcutTest(IPX): .
    RawToSnapShortcutTest(IPX): .
    RawToSapShortcutTest(IPX): .
    RawToRawShortcutTest(IPX): .
    SoftwareShortcutTest(IPX): .
    DontShortcutTest(IPX): .
    ShortcutTableFullTest(IPX): .



    Line Card Diag Status for Module 1 (. = Pass, F = Fail, N = N/A)
    CPU : . Sprom : . Bootcsum : . Archsum : .
    RAM : . LTL : . CBL : . DPRAM : .
    SAMBA : .
    Saints : N Pkt Bufs : . Repeater : N FLASH : .
    Phoenix : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .

    PHOENIX Status :
    Ports T1 R1 T2 R2
    ---------------------
    . . . .

    GIGMAC Status :
    Ports 1 2
    -----------
    . .

    PHOENIX Port Status :
    Ports 9 17 18 19 20 21 22
    INBAND A->B B->A B->C C->B A->C C->A
    ------------------------------------------
    . . . . . . .

    Packet Buffer Status :
    Ports 1 2
    -----------
    . .

    PHOENIX Packet Buffer Status :
    Ports INBAND A<->B B<->C A<->C
    ------------------------------
    . . . .

    Loopback Status [Reported by Module 1] :
    Ports 1 2 9
    --------------
    . . .

    5500> (enable) show system
    PS1-Status PS2-Status
    ---------- ----------
    ok faulty

    Fan-Status Temp-Alarm Sys-Status Uptime d,h:m:s Logout
    ---------- ---------- ---------- -------------- ---------
    ok off faulty 0,04:51:43 20 min

    PS1-Type PS2-Type
    ------------ ------------
    WS-C5508 WS-C5508

    Modem Baud Traffic Peak Peak-Time
    ------- ----- ------- ---- -------------------------
    disable 9600 0% 2% Mon Aug 6 2007, 19:23:22

    5500> (enable) show test diaglevel
    Diagnostic mode at last bootup : minimal
    Diagnostic mode at next reset : minimal
    ufik, Aug 6, 2007
    #3
  4. ufik

    Scott Perry Guest

    A Cisco Catalyst 5500 series switch will report module 1, the supervisor, as
    faulty when one of the two power supplies is not working.

    Turn the other power supply on or else replace the power supply unit if it
    has failed.

    --

    ===========
    Scott Perry
    ===========
    Indianapolis, Indiana
    ________________________________________
    "ufik" <> wrote in message
    news:...
    > Hello,
    >
    > What is mean faulty status. It is hardware problem or something else.
    > Is it normal status for Supervisor?
    >
    > 5500> (enable) sh module
    > Mod Slot Ports Module-Type Model Sub
    > Status
    > --- ---- ----- ------------------------- ------------------- ---
    > --------
    > 1 1 2 1000BaseSX Supervisor WS-X5530 yes
    > faulty
    > 2 2 Gigabit Ethernet Ext WS-X5410
    > 3 3 9 Gigabit Ethernet WS-X5410 no ok
    > 6 6 12 100BaseFX MM Ethernet WS-X5201 no ok
    > 7 7 1 Route Switch WS-X5302 no ok
    > 8 8 12 10BaseFL Ethernet WS-X5011 no ok
    > 9 9 12 100BaseFX MM Ethernet WS-X5111 no ok
    > 10 10 24 10/100BaseTX Ethernet WS-X5224 no ok
    > 11 11 36 10/100BaseTX Ethernet WS-X5239 no ok
    > 12 12 36 10/100BaseTX Ethernet WS-X5239 no ok
    >
    > Thank you for help.
    >
    Scott Perry, Aug 6, 2007
    #4
  5. ufik

    make Guest

    Its power supply 2.
    > 5500> (enable) show system
    > PS1-Status PS2-Status
    > ---------- ----------
    > ok faulty
    >>> What is mean faulty status. It is hardware problem or something else.
    >>> Is it normal status for Supervisor?
    >>> 5500> (enable) sh module
    >>> Mod Slot Ports Module-Type Model Sub
    >>> Status
    >>> --- ---- ----- ------------------------- ------------------- ---
    >>> --------
    >>> 1 1 2 1000BaseSX Supervisor WS-X5530 yes
    >>> faulty
    make, Aug 7, 2007
    #5
  6. ufik

    ufik Guest

    On 7 Sie, 05:47, make <> wrote:
    > Its power supply 2.
    > > 5500> (enable) show system
    > > PS1-Status PS2-Status
    > > ---------- ----------
    > > ok faulty

    >
    >
    >
    > >>> What is mean faulty status. It is hardware problem or something else.
    > >>> Is it normal status for Supervisor?
    > >>> 5500> (enable) sh module
    > >>> Mod Slot Ports Module-Type Model Sub
    > >>> Status
    > >>> --- ---- ----- ------------------------- ------------------- ---
    > >>> --------
    > >>> 1 1 2 1000BaseSX Supervisor WS-X5530 yes
    > >>> faulty- Ukryj cytowany tekst -

    >
    > - Poka cytowany tekst -


    Yes, now its ok
    thank you
    ufik, Aug 7, 2007
    #6
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Silverstrand

    Logitech Z-5500 Digital Speakers

    Silverstrand, Jun 29, 2005, in forum: Front Page News
    Replies:
    5
    Views:
    871
    unholy
    Jun 30, 2005
  2. JustMe

    Slot 13 in a Catalyst 5500

    JustMe, Jul 14, 2003, in forum: Cisco
    Replies:
    1
    Views:
    991
    Hansang Bae
    Jul 15, 2003
  3. Dave
    Replies:
    3
    Views:
    641
  4. Michele
    Replies:
    0
    Views:
    549
    Michele
    Apr 8, 2004
  5. cheeku
    Replies:
    7
    Views:
    1,112
    cheeku
    May 19, 2007
Loading...

Share This Page