Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > etherchannel configuration

Reply
Thread Tools

etherchannel configuration

 
 
genio genio is offline
Junior Member
Join Date: Feb 2010
Posts: 1
 
      02-04-2010
Hello experts,

I attached last time the config and error with this message. But don't know why it didn't attach. anyway i attach those files now.
I have some confusion regarding etherchannel. The scenario is

1) one the IBM blade server there are 4 cisco 3110G switch in stack and the other side there are 6 3750G switches in stack.
2) every first 2 ports of the 3110G switch are connects to 5th 3750G switch and other 2 ports of 3110G switches connect to 6 switch.
3) in total 8 ports of these four 3110G switches in port channel 5 and other 8 ports are in port channel 6.
4) the both port channels are in trunk mode and allowed 5 vlans and one of them as native vlan.

the problem arise after configure the port-channel 6 the whole network goes down. So I shut down the port channel 6. Now the port-channel 5 is working again and the rest of the network. the error log i am sending with attachment as well as the config. My question is

1) the native vlan is flapping between the two port channels. the rest will flap too as well because presently those vlans are not up.
2) i assign spanning tree cost for both port channels. but even the flapping starts after 5 minutes. so whether it will work if i apply spanning tree vlan priority higher in one port channel than the same vlans in other port channel.

i attach the config and error log too.

really grateful if somebody can assist.
Attached Files
File Type: zip config and error.zip (81.6 KB, 10 views)
 

Last edited by genio; 02-04-2010 at 02:29 PM..
Reply With Quote
 
 
 
 
donjohnston donjohnston is offline
Member
Join Date: Jun 2008
Posts: 38
 
      02-09-2010
On the 3110G, do the following for the portchannel interfaces and the physical interfaces that make up the etherchannel

no spanning-tree portfast
no spanning-tree bpdufilter enable
 
Reply With Quote
 
 
 
 
bryanpalacios bryanpalacios is offline
Junior Member
Join Date: Jan 2010
Location: Guatemala
Posts: 9
 
      02-09-2010
Quote:
Originally Posted by donjohnston
On the 3110G, do the following for the portchannel interfaces and the physical interfaces that make up the etherchannel

no spanning-tree portfast
no spanning-tree bpdufilter enable


I agree with you
 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
etherchannel (pagp or lacp) + trunk Roberto Taccon Cisco 2 11-09-2006 07:53 AM
Etherchannel Configuration on 3750 SteveO Cisco 3 09-14-2005 02:54 PM
Need Help setting up Etherchannel w/ EMC Celerra (Cisco 2970) Todd Richert Cisco 3 02-09-2004 10:22 AM
Cisco 2970 Switch, Etherchannel Problem, Layer2 Down Todd Richert Cisco 3 01-10-2004 05:27 AM
Etherchannel 4006 Roland Waidhas Cisco 0 07-13-2003 11:35 AM



Advertisments