Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > Cisco 1242ag AP downgrade to autonomous mode failure

Reply
Thread Tools

Cisco 1242ag AP downgrade to autonomous mode failure

 
 
muanivanua muanivanua is offline
Junior Member
Join Date: Jun 2008
Posts: 2
 
      06-23-2009
Hi all,

I am not able to get CLI access to cisco 1242ag ap after downgrading to autonommous mode from lwapp mode. interface kips resetting.

the following is the capture txt from the AP.

---------------------------------
Xmodem file system is available.
flashfs[0]: 137 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 4447232
flashfs[0]: Bytes available: 11551744
flashfs[0]: flashfs fsck took 26 seconds.
Base ethernet MAC Address: 00:1d:a1:ff:49:d8
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up

The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:

ether_init
tftp_init
boot

Loading "flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5"...######################################### ################################################## ################################################## ################################################## ################################################## ################################################## ################################################## ##

File "flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(7)JA5, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 27-Jul-07 14:03 by kehsiao
Image text-base: 0x00003000, data-base: 0x00681A20

Initializing flashfs...

flashfs[1]: 137 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 4447232
flashfs[1]: Bytes available: 11551744
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

cisco AIR-LAP1242AG-N-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FOC12080P30
PowerPCElvis CPU at 266Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:A1:FF:498
Part Number : 73-9925-06
PCA Assembly Number : 800-26579-05
PCA Revision Number : A0
PCB Serial Number : FOC12080P30
Top Assembly Part Number : 800-29151-02
Top Assembly Serial Number : FTX1209B29T
Top Revision Number : A0
Product/Model Number : AIR-LAP1242AG-N-K9



Press RETURN to get started!


*Mar 1 00:00:06.268: %DOT11-4-LOADING_RADIO: Interface Dot11Radio1, loading the radio firmware (flash:/c1240-k9w7-mx.123-7.JA5/6701.img)
*Mar 1 00:00:07.358: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:09.413: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:09.414: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.414: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:28.478: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:00:28.479: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:28.516: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:28.540: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(7)JA5, RELEASE SOFTWARE (fc3)

Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 27-Jul-07 14:03 by kehsiao
*Mar 1 00:00:28.540: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:29.477: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:29.479: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:29.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:40.427: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:41.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:01:00.510: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:01.510: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:10.426: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:01:11.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:01:30.511: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:01:31.512: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:01:40.426: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:01:41.427: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down

-----------------------------------

Appreciate your valuable input.

Thanks,
Ben.
 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Autonomous Cisco 1142n CLI setup stuie_norris@yahoo.com.au Cisco 0 02-12-2010 10:57 PM
Balancing users across multiple Cisco 1242AG roopjm Cisco 0 07-17-2008 03:21 PM
1242AG and fa 0 when using vlan dt1649651@yahoo.com Cisco 3 07-20-2007 03:03 AM
1242AG and WPA-PSK? mupp.net@gmail.com Cisco 1 04-24-2007 11:12 PM
Mode Switch on 1242AG mpmc1@comcast.net Cisco 1 10-25-2006 11:36 PM



Advertisments