«

Sinna schreef:
> I suggest you try to verify your land-line phone number again. I did
> recently to enable CallerID on my Linksys SPA 3102 and it works like a
> charm.
>

How did you set these settings ? i too have a SPA3102, and also
registerd my own phonenumber on cheap & buster


--
The Fug.

TheFug wrote:
> Sinna schreef:
> > I suggest you try to verify your land-line phone number again. I did
>> recently to enable CallerID on my Linksys SPA 3102 and it works like a
>> charm.
>>
>
> How did you set these settings ? i too have a SPA3102, and also
> registerd my own phonenumber on cheap & buster
>
>
Step-by-step guide:
- Log in as Administrator
- Switch to Voice Line 1 tab
- Enter something in the 'Display Name' field (it doesn't matter, I
didn't figure out where it's displayed anyhow/anyway)
- Enter your phone-number in the 'User ID' field in the
+32xxxxxxxx-format (32 is Belgium)
- Enter your password in the 'Password' field (obvious)
- Set 'Use Auth ID' to 'yes'
- Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
- apply the changes, let the gateway reboot and start calling.
- you can verify it by calling yourself on your cellphone.

Note that I verified my phonenumber also in the +32xxxxxxxx-format.
Perhaps it's related to each other, but I'm not sure.

Hope this helps,

Sinna

Sinna schreef:
> TheFug wrote:
>> Sinna schreef:
>> > I suggest you try to verify your land-line phone number again. I did
>>> recently to enable CallerID on my Linksys SPA 3102 and it works like
>>> a charm.
>>>
>>
>> How did you set these settings ? i too have a SPA3102, and also
>> registerd my own phonenumber on cheap & buster
>>
>>
> Step-by-step guide:
> - Log in as Administrator
> - Switch to Voice Line 1 tab
> - Enter something in the 'Display Name' field (it doesn't matter, I
> didn't figure out where it's displayed anyhow/anyway)
> - Enter your phone-number in the 'User ID' field in the
> +32xxxxxxxx-format (32 is Belgium)
> - Enter your password in the 'Password' field (obvious)
> - Set 'Use Auth ID' to 'yes'
> - Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
> - apply the changes, let the gateway reboot and start calling.
> - you can verify it by calling yourself on your cellphone.
>
> Note that I verified my phonenumber also in the +32xxxxxxxx-format.
> Perhaps it's related to each other, but I'm not sure.
>
> Hope this helps,
>
> Sinna

Thankyou, Sinna, that's a very clear discription, thus, if it still
doesn't work for me this way, I'm not the blame, and some "power"
greater than me, is the blame...
That saves me looking further for it, i guess.
Yes, I registered/verified it in the +31xxxxxxxxx format, all subscriber
phone numbers have (also) a 10 digit number format, here in the
Netherlands.
Did you change anything in Regional, like: Caller ID, Feature Invocatio,
method, or Caller ID FSK Standard ?
But i guess these settings could differ per country.....

--
The Fug.

Sinna presented the following explanation :
> TheFug wrote:
>> Sinna schreef:
>> > I suggest you try to verify your land-line phone number again. I did
>>> recently to enable CallerID on my Linksys SPA 3102 and it works like a
>>> charm.
>>>
>>
>> How did you set these settings ? i too have a SPA3102, and also registerd
>> my own phonenumber on cheap & buster
>>
>>
> Step-by-step guide:
> - Log in as Administrator
> - Switch to Voice Line 1 tab
> - Enter something in the 'Display Name' field (it doesn't matter, I didn't
> figure out where it's displayed anyhow/anyway)
> - Enter your phone-number in the 'User ID' field in the +32xxxxxxxx-format
> (32 is Belgium)
> - Enter your password in the 'Password' field (obvious)
> - Set 'Use Auth ID' to 'yes'
> - Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
> - apply the changes, let the gateway reboot and start calling.
> - you can verify it by calling yourself on your cellphone.
>
> Note that I verified my phonenumber also in the +32xxxxxxxx-format. Perhaps
> it's related to each other, but I'm not sure.

Very concise, thanks.

Any idea how to achieve the same when using @gw1 ?

Sinna schreef:
> TheFug wrote:
>> Sinna schreef:
>> > I suggest you try to verify your land-line phone number again. I did
>>> recently to enable CallerID on my Linksys SPA 3102 and it works like
>>> a charm.
>>>
>>
>> How did you set these settings ? i too have a SPA3102, and also
>> registerd my own phonenumber on cheap & buster
>>
>>
> Step-by-step guide:
> - Log in as Administrator
> - Switch to Voice Line 1 tab
> - Enter something in the 'Display Name' field (it doesn't matter, I
> didn't figure out where it's displayed anyhow/anyway)
> - Enter your phone-number in the 'User ID' field in the
> +32xxxxxxxx-format (32 is Belgium)
> - Enter your password in the 'Password' field (obvious)
> - Set 'Use Auth ID' to 'yes'
> - Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
> - apply the changes, let the gateway reboot and start calling.
> - you can verify it by calling yourself on your cellphone.
>
> Note that I verified my phonenumber also in the +32xxxxxxxx-format.
> Perhaps it's related to each other, but I'm not sure.
>
> Hope this helps,
>
> Sinna

Yes ! it works ! Thankyou veeeeeeery much !


--
The Fug.

TheFug schreef:
> Sinna schreef:
>> TheFug wrote:
>>> Sinna schreef:
>>> > I suggest you try to verify your land-line phone number again. I did
>>>> recently to enable CallerID on my Linksys SPA 3102 and it works like
>>>> a charm.
>>>>
>>>
>>> How did you set these settings ? i too have a SPA3102, and also
>>> registerd my own phonenumber on cheap & buster
>>>
>>>
>> Step-by-step guide:
>> - Log in as Administrator
>> - Switch to Voice Line 1 tab
>> - Enter something in the 'Display Name' field (it doesn't matter, I
>> didn't figure out where it's displayed anyhow/anyway)
>> - Enter your phone-number in the 'User ID' field in the
>> +32xxxxxxxx-format (32 is Belgium)
>> - Enter your password in the 'Password' field (obvious)
>> - Set 'Use Auth ID' to 'yes'
>> - Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
>> - apply the changes, let the gateway reboot and start calling.
>> - you can verify it by calling yourself on your cellphone.
>>
>> Note that I verified my phonenumber also in the +32xxxxxxxx-format.
>> Perhaps it's related to each other, but I'm not sure.
>>
>> Hope this helps,
>>
>> Sinna
>
> Thankyou, Sinna, that's a very clear discription, thus, if it still
> doesn't work for me this way, I'm not the blame, and some "power"
> greater than me, is the blame...
> That saves me looking further for it, i guess.
> Yes, I registered/verified it in the +31xxxxxxxxx format, all subscriber
> phone numbers have (also) a 10 digit number format, here in the
> Netherlands.
> Did you change anything in Regional, like: Caller ID, Feature Invocatio,
> method, or Caller ID FSK Standard ?
> But i guess these settings could differ per country.....
>

That last question isn't important anymore.... because it now.....works !
Thank you again Sinna ! CID (out) works perfect !

--
The Fug.

Jono schreef:
> Sinna presented the following explanation :
>> TheFug wrote:
>>> Sinna schreef:
>>> > I suggest you try to verify your land-line phone number again. I did
>>>> recently to enable CallerID on my Linksys SPA 3102 and it works like
>>>> a charm.
>>>>
>>>
>>> How did you set these settings ? i too have a SPA3102, and also
>>> registerd my own phonenumber on cheap & buster
>>>
>>>
>> Step-by-step guide:
>> - Log in as Administrator
>> - Switch to Voice Line 1 tab
>> - Enter something in the 'Display Name' field (it doesn't matter, I
>> didn't figure out where it's displayed anyhow/anyway)
>> - Enter your phone-number in the 'User ID' field in the
>> +32xxxxxxxx-format (32 is Belgium)
>> - Enter your password in the 'Password' field (obvious)
>> - Set 'Use Auth ID' to 'yes'
>> - Enter your VoipCheap/VoipBuster UserID in the 'Auth ID' field
>> - apply the changes, let the gateway reboot and start calling.
>> - you can verify it by calling yourself on your cellphone.
>>
>> Note that I verified my phonenumber also in the +32xxxxxxxx-format.
>> Perhaps it's related to each other, but I'm not sure.
>
> Very concise, thanks.
>
> Any idea how to achieve the same when using @gw1 ?
>
>

It works for me on GW1 !

--
The Fug.

TheFug explained on 28/09/2007 :

>>
>> Any idea how to achieve the same when using @gw1 ?
>>
>>
>
> It works for me on GW1 !

Oh.

I have no problem getting it to work on the Line 1 VoIP account,
however, no matter what I try, on the gateway account it doesn't work.

On the gateway section, there is only space for Auth ID & Password, no
User ID field to enter the number.......so I am surprised you've got it
working.......unless, when you said you had it working on gw1, you
actually meant Line 1

Jono schreef:
> TheFug explained on 28/09/2007 :
>
>>>
>>> Any idea how to achieve the same when using @gw1 ?
>>>
>>>
>>
>> It works for me on GW1 !
>
> Oh.
>
> I have no problem getting it to work on the Line 1 VoIP account,
> however, no matter what I try, on the gateway account it doesn't work.
>
> On the gateway section, there is only space for Auth ID & Password, no
> User ID field to enter the number.......so I am surprised you've got it
> working.......unless, when you said you had it working on gw1, you
> actually meant Line 1
>
>

You're logged into the SPA3102 as admin and advanced ?
you have to login 1st as "user" then again as "admin"
then click on "advanced" and on the tab LINE1 at the bottom, you should
see these settings.

--
The Fug.

Jono schreef:
> TheFug explained on 28/09/2007 :
>
>>>
>>> Any idea how to achieve the same when using @gw1 ?
>>>
>>>
>>
>> It works for me on GW1 !
>
> Oh.
>
> I have no problem getting it to work on the Line 1 VoIP account,
> however, no matter what I try, on the gateway account it doesn't work.
>
> On the gateway section, there is only space for Auth ID & Password, no
> User ID field to enter the number.......so I am surprised you've got it
> working.......unless, when you said you had it working on gw1, you
> actually meant Line 1
>
>

Sorry, my previous post is incorrect !
You should only do this "trick" in the section "Subscriber Information"
UserID: +31xxxxxxxxx (LINE1 tab)
The settings at the bottom, should be normal..

--
The Fug.