«

Hello,
I am trying configure communication beteewn vlan on catalyst 5500
with RSM WS-X5302 but I cant find command ip routing and router. What
can I do to !

interface Vlan11
description xxx
ip address 89.9.64.65 255.255.255.192
no ip route-cache
!
interface Vlan12
description xxx
ip address 89.9.64.129 255.255.255.192
no ip route-cache

Please help me.

writes:
>Hello,
> I am trying configure communication beteewn vlan on catalyst 5500
>with RSM WS-X5302 but I cant find command ip routing and router. What
>can I do to !

>interface Vlan11
> description xxx
> ip address 89.9.64.65 255.255.255.192
> no ip route-cache
>!
>interface Vlan12
> description xxx
> ip address 89.9.64.129 255.255.255.192
> no ip route-cache

>Please help me.


The RSM is a seperate console.

You configure switching on the Sup. You then access the RSM console
with the session command (or over its console port) and configure
routing on the RSM console.

http://www.cisco.com/univercd/cc/td/...sm/4058_01.htm

Your commands above look like l2 switching commands entered in the sup only.

Cisco never did a native combined together IOS for the 5500, that only
went into the 6500 for certain setups, or the 4500 SupIV and up.

In article <46ab70a3$0$79254$ s.com>,
Doug McIntyre <> wrote:
> writes:
>> I am trying configure communication beteewn vlan on catalyst 5500
>>with RSM WS-X5302 but I cant find command ip routing and router.

>>interface Vlan11
>> description xxx
>> ip address 89.9.64.65 255.255.255.192
>> no ip route-cache

>>interface Vlan12
>> description xxx
>> ip address 89.9.64.129 255.255.255.192
>> no ip route-cache


>You configure switching on the Sup. You then access the RSM console
>with the session command (or over its console port) and configure
>routing on the RSM console.

>Your commands above look like l2 switching commands entered in the sup only.

I have to disagree; the Cat 5000 Supervisor did not allow you
to configure per-interface IP addresses or to configure route caching.
The commands shown are obviously commands from the IOS side, living
on the RSM. The Supervisor side uses command such as "set vlan"
to define which ports are in which VLAN, but doesn't allow you to
configure how to talk between the VLANs.


The original posting is not entirely specific about where those
particular commands are from, not specific about whether they
are what the OP would -like- to put in, or what the OP already has.
If they are what the OP would -like- to put in, then your advice
to use the 'session' command is probably the solution; if
the OP pulled the commands shown off of the RSM already then
there is some other issue.

Suggest that the OP posts CATOS show version and show module output
and IOS show version output

On 28 Lip, 23:56, Merv <merv.hr...@rogers.com> wrote:
> Suggest that the OP posts CATOS show version and show module output
> and IOS show version output

WS-C5500 Software, Version McpSW: 5.5(13a) NmpSW: 5.5(13a)
Copyright (c) 1995-2002 by Cisco Systems
NMP S/W compiled on Feb 1 2002, 19:47:47
MCP S/W compiled on Feb 01 2002, 19:41:58

System Bootstrap Version: 5.1(2)

Hardware Version: 1.3 Model: WS-C5500 Serial #: 069022666

Mod Port Model Serial # Versions
--- ---- ---------- --------- ----------------------------------------
1 2 WS-X5530 022121735 Hw : 3.5
Fw : 5.1(2)
Fw1: 4.4(1)
Sw : 5.5(13a)
WS-F5531A 021601960 Hw : 2.1
WS-U5534 022372489 Hw : 1.2
3 9 WS-X5410 012879697 Hw : 1.0
Fw : 4.2(1)
Fw1: 4.2(1)
Sw : 5.5(10)
6 12 WS-X5201 009149143 Hw : 3.0
Fw : 3.1(1)
Sw : 5.5(13a)
7 1 WS-X5302 006805398 Hw : 4.5
Fw : 20.22
Fw1: 2.2(4)
Sw : 12.2(31)
8 12 WS-X5011 005858615 Hw : 1.4
Fw : 1.2
Sw : 5.5(13a)
9 12 WS-X5111 005077493 Hw : 1.0
Fw : 1.3
Sw : 5.5(13a)
10 24 WS-X5224 015725951 Hw : 1.5
Fw : 3.1(1)
Sw : 5.5(13a)
11 36 WS-X5239 024766488 Hw : 1.2
Fw : 4.5(2)
Sw : 5.5(13a)
12 36 WS-X5239 024766361 Hw : 1.2
Fw : 4.5(2)
Sw : 5.5(13a)

Router(boot)#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-BOOT-M), Version 12.2(31), RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 11-Aug-05 16:25 by tinhuang
Image text-base: 0x40010948, data-base: 0x4095E000

ROM: System Bootstrap, Version 11.2(17523) [mohsen 102], INTERIM
SOFTWARE
BOOTLDR: C5RSM Software (C5RSM-BOOT-M), Version 12.2(31), RELEASE
SOFTWARE (fc2)

Router uptime is 8 hours, 7 minutes
System returned to ROM by reload at 11:58:20 UTC Sat Jul 28 2007
Running default software

cisco RSP2 (R4700) processor with 131072K/2072K bytes of memory.
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
X.25 software, Version 3.0.0.
1 C5IP controller (41 Vlan).
41 Virtual Ethernet/IEEE 802.3 interface(s)
123K bytes of non-volatile configuration memory.

8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102

Cisco has yanked 12.2(31) for the RSM.

More current images available are:
12.2.46 (GD)
12.2.40a (GD)
12.2.40 (GD)
12.2.37 (GD)
12.2.32 (GD)


for RSM configuration docs

see http://www.cisco.com/en/US/products/...bf9a.shtml#sup


If you cannot configure "ip routing" then something is seriously
broken with the IOS image.

Your question was about how to route from a VLAN on the switch to another
VLAN on the switch through the RSM module.

Routing is enabled by default on the RSM unless you disabled it or went
through the prompted initial configuration. The command "ip routing" is
only on the RSM.

Make absolutely sure that VLAN 11 and VLAN 12 are configured on the switch
and that there are ports assigned to each of those VLANs.

It may not be a bad idea to also enable the switch and the router to access
each other by IP:

CatOS
set interface sc0 98 10.1.1.2/255.255.255.252 10.1.1.1
RSM
interface vlan 98
ip address 10.1.1.1 255.255.255.252
no shutdown

Here is your solution:

CatOS
set vlan 11
set vlan 12
set vlan 11 5/11
set vlan 12 5/12
RSM
ip routing
interface vlan 11
ip address 89.9.64.65 255.255.255.192
no shutdown
interface vlan 12
ip address 89.9.64.129 255.255.255.192
no shutdown

Even better would be to enable mulitlayer switching:

CatOS
set mls enable ip
RSM
mls rp ip

--

===========
Scott Perry
===========
Indianapolis, Indiana
________________________________________
<> wrote in message
news: oups.com...
> Hello,
> I am trying configure communication beteewn vlan on catalyst 5500
> with RSM WS-X5302 but I cant find command ip routing and router. What
> can I do to !
>
> interface Vlan11
> description xxx
> ip address 89.9.64.65 255.255.255.192
> no ip route-cache
> !
> interface Vlan12
> description xxx
> ip address 89.9.64.129 255.255.255.192
> no ip route-cache
>
> Please help me.
>