«

I have a Cisco 2610 router (older model, not the XM version) with a 4-
Port Async/Sync Network Module (NM-4A/S). I'm trying control a serial
device through an IP connection to the router.

I am able to get a connection from the router to the serial device,
but I cannot connect from a PC to the router at 192.168.21.110 : 2033
(or 4033 or any 20XX or 40XX ports). For some reason I can connect to
port 80 which I though was kind of strange.

Any help would certainly be appreciated.

Chris

******************************
* Here is my configuration
******************************

wbtermsrv1#show config
Using 1955 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password dci640
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
ip address 192.168.21.110 255.255.255.0
no ip mroute-cache
no keepalive
clock rate 9600
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
password edocatad
login
!
end

*******************************************
* Here is my interface
*******************************************

wbtermsrv1#show interface
Ethernet0/0 is up, line protocol is up
Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
Description: LAN Interface
Internet address is 10.144.80.1/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 33000 bits/sec, 28 packets/sec
5 minute output rate 28000 bits/sec, 28 packets/sec
6601821 packets input, 984548685 bytes, 0 no buffer
Received 559810 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
6126567 packets output, 812593676 bytes, 0 underruns
6 output errors, 563 collisions, 1 interface resets
0 babbles, 0 late collision, 80518 deferred
6 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial1/0 is up, line protocol is up
Hardware is CD2430 in sync mode
Internet address is 192.168.21.110/24
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive not set
Last input never, output 01:12:19, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
169 packets output, 10138 bytes, 0 underruns
0 output errors, 0 collisions, 393 interface resets
0 output buffer failures, 0 output buffers swapped out
51 carrier transitions
DCD=up DSR=up DTR=up RTS=down CTS=up
Serial1/1 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
25838 packets output, 620112 bytes, 0 underruns
0 output errors, 0 collisions, 11478 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/2 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
33598 packets output, 806352 bytes, 0 underruns
0 output errors, 0 collisions, 11479 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/3 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
25836 packets output, 620064 bytes, 0 underruns
0 output errors, 0 collisions, 11477 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Loopback0 is up, line protocol is up
Hardware is Loopback
Description: GRE Tunnel Source Interface
Internet address is 10.144.0.80/32
MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Description: GRE Tunnel Interface
Internet address is 10.144.2.26/30
MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
reliability 255/255, txload 1/255, rxload 119/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
Checksumming of packets disabled, fast tunneling enabled
Last input 00:00:04, output 00:00:11, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
11
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 28000 bits/sec, 26 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
5910678 packets input, 855822425 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
55259 packets output, 4314430 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out

You need 'physical-layer async' on the A/S serial interface, to put it
into async mode. Then on the corresponding line, configure this for a
"console server" application:

line 33
no exec
transport input telnet
modem dtr-active

Then you can telnet to TCP port 2033 to talk out this line to the async
device.

Regards,

Aaron

---

~ I have a Cisco 2610 router (older model, not the XM version) with a 4-
~ Port Async/Sync Network Module (NM-4A/S). I'm trying control a serial
~ device through an IP connection to the router.
~
~ I am able to get a connection from the router to the serial device,
~ but I cannot connect from a PC to the router at 192.168.21.110 : 2033
~ (or 4033 or any 20XX or 40XX ports). For some reason I can connect to
~ port 80 which I though was kind of strange.
~
~ Any help would certainly be appreciated.
~
~ Chris
~
~ ******************************
~ * Here is my configuration
~ ******************************
~
~ wbtermsrv1#show config
~ Using 1955 out of 29688 bytes
~ !
~ version 12.2
~ service timestamps debug uptime
~ service timestamps log uptime
~ no service password-encryption
~ !
~ hostname wbtermsrv1
~ !
~ boot system flash:c2600-is-mz.122-40a.bin
~ logging buffered 8192 debugging
~ enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
~ enable password dci640
~ !
~ ip subnet-zero
~ ip cef
~ !
~ !
~ no ip domain-lookup
~ !
~ ip multicast-routing
~ call rsvp-sync
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ interface Loopback0
~ description GRE Tunnel Source Interface
~ ip address 10.144.0.80 255.255.255.255
~ !
~ interface Tunnel0
~ description GRE Tunnel Interface
~ ip address 10.144.2.26 255.255.255.252
~ ip accounting output-packets
~ ip pim sparse-mode
~ tunnel source Loopback0
~ tunnel destination 10.144.254.1
~ !
~ interface Ethernet0/0
~ description LAN Interface
~ ip address 192.168.20.110 255.255.255.0 secondary
~ ip address 10.144.80.1 255.255.255.0
~ ip accounting output-packets
~ ip pim neighbor-filter 2
~ ip pim sparse-mode
~ ip route-cache flow
~ no ip route-cache cef
~ half-duplex
~ no cdp enable
~ !
~ interface Serial1/0
~ ip address 192.168.21.110 255.255.255.0
~ no ip mroute-cache
~ no keepalive
~ clock rate 9600
~ !
~ interface Serial1/1
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/2
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/3
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ ip classless
~ ip route 0.0.0.0 0.0.0.0 192.168.20.164
~ ip route 10.132.19.8 255.255.255.255 Tunnel0
~ ip http server
~ ip pim rp-address 10.132.19.8
~ ip pim spt-threshold infinity
~ ip mroute 10.132.19.8 255.255.255.255 Tunnel0
~ !
~ access-list 2 remark DISABLE DESIGNATED ROUTER
~ access-list 2 remark
~ access-list 2 deny any
~ access-list 111 remark used for debugging traffic
~ access-list 111 remark
~ access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
~ access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
~ no cdp run
~ !
~ dial-peer cor custom
~ !
~ !
~ !
~ !
~ line con 0
~ exec-timeout 0 0
~ line aux 0
~ line vty 0 4
~ password edocatad
~ login
~ !
~ end
~
~ *******************************************
~ * Here is my interface
~ *******************************************
~
~ wbtermsrv1#show interface
~ Ethernet0/0 is up, line protocol is up
~ Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
~ Description: LAN Interface
~ Internet address is 10.144.80.1/24
~ MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation ARPA, loopback not set
~ Keepalive set (10 sec)
~ ARP type: ARPA, ARP Timeout 04:00:00
~ Last input 00:00:00, output 00:00:00, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/40 (size/max)
~ 5 minute input rate 33000 bits/sec, 28 packets/sec
~ 5 minute output rate 28000 bits/sec, 28 packets/sec
~ 6601821 packets input, 984548685 bytes, 0 no buffer
~ Received 559810 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
~ 0 input packets with dribble condition detected
~ 6126567 packets output, 812593676 bytes, 0 underruns
~ 6 output errors, 563 collisions, 1 interface resets
~ 0 babbles, 0 late collision, 80518 deferred
~ 6 lost carrier, 0 no carrier
~ 0 output buffer failures, 0 output buffers swapped out
~ Serial1/0 is up, line protocol is up
~ Hardware is CD2430 in sync mode
~ Internet address is 192.168.21.110/24
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive not set
~ Last input never, output 01:12:19, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 169 packets output, 10138 bytes, 0 underruns
~ 0 output errors, 0 collisions, 393 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 51 carrier transitions
~ DCD=up DSR=up DTR=up RTS=down CTS=up
~ Serial1/1 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:02, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 25838 packets output, 620112 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11478 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/2 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:03, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 33598 packets output, 806352 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11479 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 2 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/3 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:04, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 25836 packets output, 620064 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11477 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Loopback0 is up, line protocol is up
~ Hardware is Loopback
~ Description: GRE Tunnel Source Interface
~ Internet address is 10.144.0.80/32
~ MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation LOOPBACK, loopback not set
~ Last input never, output never, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 0 packets output, 0 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ Tunnel0 is up, line protocol is up
~ Hardware is Tunnel
~ Description: GRE Tunnel Interface
~ Internet address is 10.144.2.26/30
~ MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
~ reliability 255/255, txload 1/255, rxload 119/255
~ Encapsulation TUNNEL, loopback not set
~ Keepalive not set
~ Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
~ Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
~ Checksumming of packets disabled, fast tunneling enabled
~ Last input 00:00:04, output 00:00:11, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 11
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 28000 bits/sec, 26 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 5910678 packets input, 855822425 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 55259 packets output, 4314430 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out

Aaron,

I followed your directions but still can't connect. Here is the
results. The Serial 1/0 line is now down. I have it connected to a
Hyperterminal session with the settings 9600, 8 databits, No parity, 2
stopbits, Hardware flow control.

Chris


****************************************
* new config
****************************************

wbtermsrv1#show config
Using 2012 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
physical-layer async
no ip address
encapsulation slip
shutdown
async default routing
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line 33
modem DTR-active
no exec
transport input telnet
line aux 0
line vty 0 4
password edocatad
login
!
end
wbtermsrv1#show config
Using 2012 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password dci640
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
physical-layer async
no ip address
encapsulation slip
shutdown
async default routing
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line 33
modem DTR-active
no exec
transport input telnet
line aux 0
line vty 0 4
password edocatad
login
!
end

************************************************
* new interface
************************************************

wbtermsrv1#show interface
Ethernet0/0 is up, line protocol is up
Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
Description: LAN Interface
Internet address is 10.144.80.1/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 11000 bits/sec, 12 packets/sec
5 minute output rate 9000 bits/sec, 10 packets/sec
6910660 packets input, 1028585734 bytes, 0 no buffer
Received 585985 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
6412939 packets output, 848479146 bytes, 0 underruns
6 output errors, 600 collisions, 1 interface resets
0 babbles, 0 late collision, 91614 deferred
6 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial1/0 is administratively down, line protocol is down
Hardware is CD2430 in async mode
MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not set
DTR is pulsed for 5 seconds on reset
Last input never, output 3d08h, output hang never
Last clearing of "show interface" counters 3d02h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 6 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Serial1/1 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27391 packets output, 657384 bytes, 0 underruns
0 output errors, 0 collisions, 11996 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/2 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
35152 packets output, 843648 bytes, 0 underruns
0 output errors, 0 collisions, 11997 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Serial1/3 is up, line protocol is down
Hardware is CD2430 in sync mode
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27390 packets output, 657360 bytes, 0 underruns
0 output errors, 0 collisions, 11995 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Loopback0 is up, line protocol is up
Hardware is Loopback
Description: GRE Tunnel Source Interface
Internet address is 10.144.0.80/32
MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Description: GRE Tunnel Interface
Internet address is 10.144.2.26/30
MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
reliability 255/255, txload 1/255, rxload 113/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
Checksumming of packets disabled, fast tunneling enabled
Last input 00:00:01, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
11
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 4000 bits/sec, 5 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6192424 packets input, 894132772 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
57863 packets output, 4517542 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out

On 23 Apr 2007 13:52:17 -0700, MtbRoadie <> wrote:

~ Aaron,
~
~ I followed your directions but still can't connect. Here is the
~ results. The Serial 1/0 line is now down. I have it connected to a
~ Hyperterminal session with the settings 9600, 8 databits, No parity, 2
~ stopbits, Hardware flow control.
~
~ Chris
~
~
~ ****************************************
~ * new config
~ ****************************************
~
~ wbtermsrv1#show config
~ Using 2012 out of 29688 bytes
~ !
~ version 12.2
~ service timestamps debug uptime
~ service timestamps log uptime
~ no service password-encryption
~ !
~ hostname wbtermsrv1
~ !
~ boot system flash:c2600-is-mz.122-40a.bin
~ logging buffered 8192 debugging
~ enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
~ enable password
~ !
~ ip subnet-zero
~ ip cef
~ !
~ !
~ no ip domain-lookup
~ !
~ ip multicast-routing
~ call rsvp-sync
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ interface Loopback0
~ description GRE Tunnel Source Interface
~ ip address 10.144.0.80 255.255.255.255
~ !
~ interface Tunnel0
~ description GRE Tunnel Interface
~ ip address 10.144.2.26 255.255.255.252
~ ip accounting output-packets
~ ip pim sparse-mode
~ tunnel source Loopback0
~ tunnel destination 10.144.254.1
~ !
~ interface Ethernet0/0
~ description LAN Interface
~ ip address 192.168.20.110 255.255.255.0 secondary
~ ip address 10.144.80.1 255.255.255.0
~ ip accounting output-packets
~ ip pim neighbor-filter 2
~ ip pim sparse-mode
~ ip route-cache flow
~ no ip route-cache cef
~ half-duplex
~ no cdp enable
~ !
~ interface Serial1/0
~ physical-layer async
~ no ip address
~ encapsulation slip
~ shutdown
~ async default routing
~ !
~ interface Serial1/1
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/2
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/3
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ ip classless
~ ip route 0.0.0.0 0.0.0.0 192.168.20.164
~ ip route 10.132.19.8 255.255.255.255 Tunnel0
~ ip http server
~ ip pim rp-address 10.132.19.8
~ ip pim spt-threshold infinity
~ ip mroute 10.132.19.8 255.255.255.255 Tunnel0
~ !
~ access-list 2 remark DISABLE DESIGNATED ROUTER
~ access-list 2 remark
~ access-list 2 deny any
~ access-list 111 remark used for debugging traffic
~ access-list 111 remark
~ access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
~ access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
~ no cdp run
~ !
~ dial-peer cor custom
~ !
~ !
~ !
~ !
~ line con 0
~ exec-timeout 0 0
~ line 33
~ modem DTR-active
~ no exec
~ transport input telnet
~ line aux 0
~ line vty 0 4
~ password edocatad
~ login
~ !
~ end
~ wbtermsrv1#show config
~ Using 2012 out of 29688 bytes
~ !
~ version 12.2
~ service timestamps debug uptime
~ service timestamps log uptime
~ no service password-encryption
~ !
~ hostname wbtermsrv1
~ !
~ boot system flash:c2600-is-mz.122-40a.bin
~ logging buffered 8192 debugging
~ enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
~ enable password dci640
~ !
~ ip subnet-zero
~ ip cef
~ !
~ !
~ no ip domain-lookup
~ !
~ ip multicast-routing
~ call rsvp-sync
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ interface Loopback0
~ description GRE Tunnel Source Interface
~ ip address 10.144.0.80 255.255.255.255
~ !
~ interface Tunnel0
~ description GRE Tunnel Interface
~ ip address 10.144.2.26 255.255.255.252
~ ip accounting output-packets
~ ip pim sparse-mode
~ tunnel source Loopback0
~ tunnel destination 10.144.254.1
~ !
~ interface Ethernet0/0
~ description LAN Interface
~ ip address 192.168.20.110 255.255.255.0 secondary
~ ip address 10.144.80.1 255.255.255.0
~ ip accounting output-packets
~ ip pim neighbor-filter 2
~ ip pim sparse-mode
~ ip route-cache flow
~ no ip route-cache cef
~ half-duplex
~ no cdp enable
~ !
~ interface Serial1/0
~ physical-layer async
~ no ip address
~ encapsulation slip
~ shutdown
~ async default routing
~ !
~ interface Serial1/1
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/2
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/3
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ ip classless
~ ip route 0.0.0.0 0.0.0.0 192.168.20.164
~ ip route 10.132.19.8 255.255.255.255 Tunnel0
~ ip http server
~ ip pim rp-address 10.132.19.8
~ ip pim spt-threshold infinity
~ ip mroute 10.132.19.8 255.255.255.255 Tunnel0
~ !
~ access-list 2 remark DISABLE DESIGNATED ROUTER
~ access-list 2 remark
~ access-list 2 deny any
~ access-list 111 remark used for debugging traffic
~ access-list 111 remark
~ access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
~ access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
~ no cdp run
~ !
~ dial-peer cor custom
~ !
~ !
~ !
~ !
~ line con 0
~ exec-timeout 0 0
~ line 33
~ modem DTR-active
~ no exec
~ transport input telnet
~ line aux 0
~ line vty 0 4
~ password edocatad
~ login
~ !
~ end
~
~ ************************************************
~ * new interface
~ ************************************************
~
~ wbtermsrv1#show interface
~ Ethernet0/0 is up, line protocol is up
~ Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
~ Description: LAN Interface
~ Internet address is 10.144.80.1/24
~ MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation ARPA, loopback not set
~ Keepalive set (10 sec)
~ ARP type: ARPA, ARP Timeout 04:00:00
~ Last input 00:00:00, output 00:00:00, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/40 (size/max)
~ 5 minute input rate 11000 bits/sec, 12 packets/sec
~ 5 minute output rate 9000 bits/sec, 10 packets/sec
~ 6910660 packets input, 1028585734 bytes, 0 no buffer
~ Received 585985 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
~ 0 input packets with dribble condition detected
~ 6412939 packets output, 848479146 bytes, 0 underruns
~ 6 output errors, 600 collisions, 1 interface resets
~ 0 babbles, 0 late collision, 91614 deferred
~ 6 lost carrier, 0 no carrier
~ 0 output buffer failures, 0 output buffers swapped out
~ Serial1/0 is administratively down, line protocol is down
~ Hardware is CD2430 in async mode
~ MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation SLIP, loopback not set
~ Keepalive not set
~ DTR is pulsed for 5 seconds on reset
~ Last input never, output 3d08h, output hang never
~ Last clearing of "show interface" counters 3d02h
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/16 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 6 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 0 packets output, 0 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 0 carrier transitions
~ Serial1/1 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:09, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 27391 packets output, 657384 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11996 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/2 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:00, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 35152 packets output, 843648 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11997 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 2 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/3 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:02, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 27390 packets output, 657360 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11995 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Loopback0 is up, line protocol is up
~ Hardware is Loopback
~ Description: GRE Tunnel Source Interface
~ Internet address is 10.144.0.80/32
~ MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation LOOPBACK, loopback not set
~ Last input never, output never, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 0 packets output, 0 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ Tunnel0 is up, line protocol is up
~ Hardware is Tunnel
~ Description: GRE Tunnel Interface
~ Internet address is 10.144.2.26/30
~ MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
~ reliability 255/255, txload 1/255, rxload 113/255
~ Encapsulation TUNNEL, loopback not set
~ Keepalive not set
~ Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
~ Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
~ Checksumming of packets disabled, fast tunneling enabled
~ Last input 00:00:01, output 00:00:02, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 11
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 4000 bits/sec, 5 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 6192424 packets input, 894132772 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 57863 packets output, 4517542 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out

Chris,

In what sense can you not connect?

Note that interfaces are irrelevant from the standpoint of a "terminal server"
setup. What counts are lines not interfaces. (Except in that you need to
configure an A/S interface for "physical-layer async" if you want to do async.)

Configuring a Terminal/Comm Server
http://www.cisco.com/en/US/tech/tk80...8014f8e7.shtml

Basically, just do a "show line <n>" to make sure that the line is in the right state.

Then telnet <router ip address> <2000+line> and you should be talking out that line.

If it doesn't seem like this works, then you've got the wrong speed, or
hw flow isn't right for you, or you have a bad cable etc.

Regards,

Aaron

---

~ Aaron,
~
~ I followed your directions but still can't connect. Here is the
~ results. The Serial 1/0 line is now down. I have it connected to a
~ Hyperterminal session with the settings 9600, 8 databits, No parity, 2
~ stopbits, Hardware flow control.
~
~ Chris
~
~
~ ****************************************
~ * new config
~ ****************************************
~
~ wbtermsrv1#show config
~ Using 2012 out of 29688 bytes
~ !
~ version 12.2
~ service timestamps debug uptime
~ service timestamps log uptime
~ no service password-encryption
~ !
~ hostname wbtermsrv1
~ !
~ boot system flash:c2600-is-mz.122-40a.bin
~ logging buffered 8192 debugging
~ enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
~ enable password
~ !
~ ip subnet-zero
~ ip cef
~ !
~ !
~ no ip domain-lookup
~ !
~ ip multicast-routing
~ call rsvp-sync
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ interface Loopback0
~ description GRE Tunnel Source Interface
~ ip address 10.144.0.80 255.255.255.255
~ !
~ interface Tunnel0
~ description GRE Tunnel Interface
~ ip address 10.144.2.26 255.255.255.252
~ ip accounting output-packets
~ ip pim sparse-mode
~ tunnel source Loopback0
~ tunnel destination 10.144.254.1
~ !
~ interface Ethernet0/0
~ description LAN Interface
~ ip address 192.168.20.110 255.255.255.0 secondary
~ ip address 10.144.80.1 255.255.255.0
~ ip accounting output-packets
~ ip pim neighbor-filter 2
~ ip pim sparse-mode
~ ip route-cache flow
~ no ip route-cache cef
~ half-duplex
~ no cdp enable
~ !
~ interface Serial1/0
~ physical-layer async
~ no ip address
~ encapsulation slip
~ shutdown
~ async default routing
~ !
~ interface Serial1/1
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/2
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/3
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ ip classless
~ ip route 0.0.0.0 0.0.0.0 192.168.20.164
~ ip route 10.132.19.8 255.255.255.255 Tunnel0
~ ip http server
~ ip pim rp-address 10.132.19.8
~ ip pim spt-threshold infinity
~ ip mroute 10.132.19.8 255.255.255.255 Tunnel0
~ !
~ access-list 2 remark DISABLE DESIGNATED ROUTER
~ access-list 2 remark
~ access-list 2 deny any
~ access-list 111 remark used for debugging traffic
~ access-list 111 remark
~ access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
~ access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
~ no cdp run
~ !
~ dial-peer cor custom
~ !
~ !
~ !
~ !
~ line con 0
~ exec-timeout 0 0
~ line 33
~ modem DTR-active
~ no exec
~ transport input telnet
~ line aux 0
~ line vty 0 4
~ password edocatad
~ login
~ !
~ end
~ wbtermsrv1#show config
~ Using 2012 out of 29688 bytes
~ !
~ version 12.2
~ service timestamps debug uptime
~ service timestamps log uptime
~ no service password-encryption
~ !
~ hostname wbtermsrv1
~ !
~ boot system flash:c2600-is-mz.122-40a.bin
~ logging buffered 8192 debugging
~ enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
~ enable password dci640
~ !
~ ip subnet-zero
~ ip cef
~ !
~ !
~ no ip domain-lookup
~ !
~ ip multicast-routing
~ call rsvp-sync
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ !
~ interface Loopback0
~ description GRE Tunnel Source Interface
~ ip address 10.144.0.80 255.255.255.255
~ !
~ interface Tunnel0
~ description GRE Tunnel Interface
~ ip address 10.144.2.26 255.255.255.252
~ ip accounting output-packets
~ ip pim sparse-mode
~ tunnel source Loopback0
~ tunnel destination 10.144.254.1
~ !
~ interface Ethernet0/0
~ description LAN Interface
~ ip address 192.168.20.110 255.255.255.0 secondary
~ ip address 10.144.80.1 255.255.255.0
~ ip accounting output-packets
~ ip pim neighbor-filter 2
~ ip pim sparse-mode
~ ip route-cache flow
~ no ip route-cache cef
~ half-duplex
~ no cdp enable
~ !
~ interface Serial1/0
~ physical-layer async
~ no ip address
~ encapsulation slip
~ shutdown
~ async default routing
~ !
~ interface Serial1/1
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/2
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ interface Serial1/3
~ no ip address
~ no ip mroute-cache
~ no cdp enable
~ !
~ ip classless
~ ip route 0.0.0.0 0.0.0.0 192.168.20.164
~ ip route 10.132.19.8 255.255.255.255 Tunnel0
~ ip http server
~ ip pim rp-address 10.132.19.8
~ ip pim spt-threshold infinity
~ ip mroute 10.132.19.8 255.255.255.255 Tunnel0
~ !
~ access-list 2 remark DISABLE DESIGNATED ROUTER
~ access-list 2 remark
~ access-list 2 deny any
~ access-list 111 remark used for debugging traffic
~ access-list 111 remark
~ access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
~ access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
~ no cdp run
~ !
~ dial-peer cor custom
~ !
~ !
~ !
~ !
~ line con 0
~ exec-timeout 0 0
~ line 33
~ modem DTR-active
~ no exec
~ transport input telnet
~ line aux 0
~ line vty 0 4
~ password edocatad
~ login
~ !
~ end
~
~ ************************************************
~ * new interface
~ ************************************************
~
~ wbtermsrv1#show interface
~ Ethernet0/0 is up, line protocol is up
~ Hardware is AmdP2, address is 0003.e381.bbe0 (bia 0003.e381.bbe0)
~ Description: LAN Interface
~ Internet address is 10.144.80.1/24
~ MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation ARPA, loopback not set
~ Keepalive set (10 sec)
~ ARP type: ARPA, ARP Timeout 04:00:00
~ Last input 00:00:00, output 00:00:00, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/40 (size/max)
~ 5 minute input rate 11000 bits/sec, 12 packets/sec
~ 5 minute output rate 9000 bits/sec, 10 packets/sec
~ 6910660 packets input, 1028585734 bytes, 0 no buffer
~ Received 585985 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
~ 0 input packets with dribble condition detected
~ 6412939 packets output, 848479146 bytes, 0 underruns
~ 6 output errors, 600 collisions, 1 interface resets
~ 0 babbles, 0 late collision, 91614 deferred
~ 6 lost carrier, 0 no carrier
~ 0 output buffer failures, 0 output buffers swapped out
~ Serial1/0 is administratively down, line protocol is down
~ Hardware is CD2430 in async mode
~ MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation SLIP, loopback not set
~ Keepalive not set
~ DTR is pulsed for 5 seconds on reset
~ Last input never, output 3d08h, output hang never
~ Last clearing of "show interface" counters 3d02h
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/16 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 6 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 0 packets output, 0 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 0 carrier transitions
~ Serial1/1 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:09, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 27391 packets output, 657384 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11996 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/2 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:00, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 35152 packets output, 843648 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11997 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 2 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Serial1/3 is up, line protocol is down
~ Hardware is CD2430 in sync mode
~ MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation HDLC, loopback not set
~ Keepalive set (10 sec)
~ Last input never, output 00:00:02, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: weighted fair
~ Output queue: 0/1000/64/0 (size/max total/threshold/drops)
~ Conversations 0/1/32 (active/max active/max total)
~ Reserved Conversations 0/0 (allocated/max allocated)
~ Available Bandwidth 96 kilobits/sec
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 27390 packets output, 657360 bytes, 0 underruns
~ 0 output errors, 0 collisions, 11995 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ 1 carrier transitions
~ DCD=up DSR=up DTR=up RTS=up CTS=up
~ Loopback0 is up, line protocol is up
~ Hardware is Loopback
~ Description: GRE Tunnel Source Interface
~ Internet address is 10.144.0.80/32
~ MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
~ reliability 255/255, txload 1/255, rxload 1/255
~ Encapsulation LOOPBACK, loopback not set
~ Last input never, output never, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 0
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 0 bits/sec, 0 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 0 packets input, 0 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 0 packets output, 0 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out
~ Tunnel0 is up, line protocol is up
~ Hardware is Tunnel
~ Description: GRE Tunnel Interface
~ Internet address is 10.144.2.26/30
~ MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
~ reliability 255/255, txload 1/255, rxload 113/255
~ Encapsulation TUNNEL, loopback not set
~ Keepalive not set
~ Tunnel source 10.144.0.80 (Loopback0), destination 10.144.254.1
~ Tunnel protocol/transport GRE/IP, key disabled, sequencing disabled
~ Checksumming of packets disabled, fast tunneling enabled
~ Last input 00:00:01, output 00:00:02, output hang never
~ Last clearing of "show interface" counters never
~ Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
~ 11
~ Queueing strategy: fifo
~ Output queue: 0/0 (size/max)
~ 5 minute input rate 4000 bits/sec, 5 packets/sec
~ 5 minute output rate 0 bits/sec, 0 packets/sec
~ 6192424 packets input, 894132772 bytes, 0 no buffer
~ Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
~ 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
~ 57863 packets output, 4517542 bytes, 0 underruns
~ 0 output errors, 0 collisions, 0 interface resets
~ 0 output buffer failures, 0 output buffers swapped out

On Apr 24, 7:03 pm, Aaron Leonard <A...@Cisco.COM> wrote:
> Chris,
>
> In what sense can you not connect?
>
> Note that interfaces are irrelevant from the standpoint of a "terminal server"
> setup. What counts are lines not interfaces. (Except in that you need to
> configure an A/S interface for "physical-layer async" if you want to do async.)
>
> Configuring a Terminal/Comm Serverhttp://www.cisco.com/en/US/tech/tk801/tk36/technologies_configuration...
>
> Basically, just do a "show line <n>" to make sure that the line is in the right state.
>
> Then telnet <router ip address> <2000+line> and you should be talking out that line.
>
> If it doesn't seem like this works, then you've got the wrong speed, or
> hw flow isn't right for you, or you have a bad cable etc.
>
> Regards,
>
> Aaron
>

Aaron,

/////////////////////////////////////////////////////////////////////////////////////////////////
Here is the status of Line 33, it appears to be connected and active.
/////////////////////////////////////////////////////////////////////////////////////////////////

wbtermsrv1#show line 33
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
Overruns Int
* 33 TTY 9600/9600 - DTR-Act - - - 3 0
0/0 Se1/0

Line 33, Location: "", Type: ""
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600, no parity, 1 stopbits, 8 databits
Status: Ready, Connected, Active
Capabilities: EXEC Suppressed, Modem DTR-Active
Modem state: Ready
Modem hardware state: CTS* DSR* DTR RTS
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none any
Timeouts: Idle EXEC Idle Session Modem Answer Session
Dispatch
00:10:00 never none
not set
Idle Session Disconnect Warning
never
Login-sequence User Response
00:00:30
Autoselect Initial Wait
not set
Modem type is unknown.
Session limit is not set.
Time since activation: never
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed input transports are pad v120 telnet rlogin udptn.
Allowed output transports are pad v120 telnet rlogin.
Preferred transport is telnet.
No output characters are padded
No special data dispatching characters
wbtermsrv1#

/////////////////////////////////////////////////////////////////////////////////
But when I try to connect I get this
/////////////////////////////////////////////////////////////////////////////////

C:\>telnet 192.168.20.110 2033
Connecting To 192.168.20.110...Could not open connection to the host,
on port 2033: Connect failed

////////////////////////////////////////////////////////////////////////////////
Here is my show config
////////////////////////////////////////////////////////////////////////////////

wbtermsrv1#show config
Using 2063 out of 29688 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname wbtermsrv1
!
boot system flash:c2600-is-mz.122-40a.bin
logging buffered 8192 debugging
enable secret 5 $1$L5RR$EULAIm6CC6oF6TCrIOoNc0
enable password xxxxxxx
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
ip host TLUX1 2033 192.168.20.110
!
ip multicast-routing
call rsvp-sync
!
!
!
!
!
!
!
!
interface Loopback0
description GRE Tunnel Source Interface
ip address 10.144.0.80 255.255.255.255
!
interface Tunnel0
description GRE Tunnel Interface
ip address 10.144.2.26 255.255.255.252
ip accounting output-packets
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.144.254.1
!
interface Ethernet0/0
description LAN Interface
ip address 192.168.20.110 255.255.255.0 secondary
ip address 10.144.80.1 255.255.255.0
ip accounting output-packets
ip pim neighbor-filter 2
ip pim sparse-mode
ip route-cache flow
no ip route-cache cef
half-duplex
no cdp enable
!
interface Serial1/0
physical-layer async
no ip address
encapsulation slip
!
interface Serial1/1
no ip address
no ip mroute-cache
no cdp enable
!
interface Serial1/2
physical-layer async
no ip address
encapsulation bstun
!
interface Serial1/3
no ip address
no ip mroute-cache
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.20.164
ip route 10.132.19.8 255.255.255.255 Tunnel0
ip http server
ip pim rp-address 10.132.19.8
ip pim spt-threshold infinity
ip mroute 10.132.19.8 255.255.255.255 Tunnel0
!
access-list 2 remark DISABLE DESIGNATED ROUTER
access-list 2 remark
access-list 2 deny any
access-list 111 remark used for debugging traffic
access-list 111 remark
access-list 111 permit ip host 10.144.80.141 233.119.160.0 0.0.0.255
access-list 111 permit ip host 10.144.80.141 10.0.0.0 0.255.255.255
no cdp run
!
dial-peer cor custom
!
!
!
!
line con 0
exec-timeout 0 0
line 33
no activation-character
modem DTR-active
no exec
transport input all
stopbits 1
line 35
line aux 0
line vty 0 4
password xxxxxxxxxx
login
!
end

Regards,

Chris

Aaron,

Nevermind.

I got into line 34 (port 2034). Must be something wrong with line 33
as I set them up the exact same way.

Thanks for your suggestions, they really helped.

Chris

Aaron,

Nevermind. I got in on line 34. Must be something wrong with line 33
as I set them up the same way.

Thanks for you suggestions, they really helped.

Regards,

Chris

On Apr 27, 12:04 pm, MtbRoadie <smilin...@hotmail.com> wrote:
> Aaron,
>
> Nevermind. I got in on line 34. Must be something wrong with line 33
> as I set them up the same way.
>
> Thanks for you suggestions, they really helped.
>
> Regards,
>
> Chris

Helpful tips for async connections:

Use the 'clear <line>' and/or 'disconnect <session>' commands to reset
the lines. The error message you saw when trying to connect sometimes
indicates the line is used or hung.