Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > Cisco 1720 frame relay to Motorola HELP!

Reply
Thread Tools

Cisco 1720 frame relay to Motorola HELP!

 
 
Todd
Guest
Posts: n/a
 
      10-06-2005
I'm ABSOLUTLEY STUMPED!!! I desperately need help.
I have a frame relay line going from out main office "Denver" to a
remote site "Baltimore"

My Cisco 1720 interfaces all show UP/UP status and shows LMI, but from
its console I can't ping the Serial0.1 interface (192.168.253.250)

On the Motorola, the config looks good and from its console I can ping
its Serial (192.168.253.249) and it sees the circuit and everything
looks good. It CAN'T see 192.168.253.250 though.

Whats wrong? I spent about an hour yesterday on the phone with
Motorola and everything looks good on that end. And as far as I know,
the Cisco looks right. Am I missing something? I'm not at the remote
(Baltimore) site, but I can VPN in and see the router. Is there
something physical that could be causing this? (bad cable, etc) Or is
it a config thing? I've confirmed the DLCI and timeslots. I'm getting
A LOT of heat to get this fixed and I'm out of ideas!!!

I'm including the interface config on the 1720 and a sho int0

interface Serial0
bandwidth 256
no ip address
encapsulation frame-relay IETF
service-module t1 timeslots 1-4
frame-relay lmi-type ansi
!
interface Serial0.1 point-to-point
ip address 192.168.253.250 255.255.255.0
frame-relay interface-dlci 16 IETF

bal-den#sho int s0
Serial0 is up, line protocol is up
Hardware is PQUICC with Fractional T1 CSU/DSU
MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF, loopback not set
Keepalive set (10 sec)
LMI enq sent 14905, LMI stat recvd 14295, LMI upd recvd 0, DTE LMI
up
LMI enq recvd 608, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 6460/0, interface
broadcasts 5155
Last input 00:00:00, output 00:00:02, output hang never
Last clearing of "show interface" counters 1d17h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/2/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
29265 packets input, 283193 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 2 giants, 0 throttles
150 input errors, 34 CRC, 67 frame, 0 overrun, 0 ignored, 48 abort
35341 packets output, 1974602 bytes, 0 underruns
0 output errors, 0 collisions, 202 interface resets
0 output buffer failures, 0 output buffers swapped out
5 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

bal-den#sho int s0.1
Serial0.1 is up, line protocol is up
Hardware is PQUICC with Fractional T1 CSU/DSU
Internet address is 192.168.253.250/24
MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF

 
Reply With Quote
 
 
 
 
Brian V
Guest
Posts: n/a
 
      10-06-2005

"Todd" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed) ps.com...
> I'm ABSOLUTLEY STUMPED!!! I desperately need help.
> I have a frame relay line going from out main office "Denver" to a
> remote site "Baltimore"
>
> My Cisco 1720 interfaces all show UP/UP status and shows LMI, but from
> its console I can't ping the Serial0.1 interface (192.168.253.250)
>
> On the Motorola, the config looks good and from its console I can ping
> its Serial (192.168.253.249) and it sees the circuit and everything
> looks good. It CAN'T see 192.168.253.250 though.
>
> Whats wrong? I spent about an hour yesterday on the phone with
> Motorola and everything looks good on that end. And as far as I know,
> the Cisco looks right. Am I missing something? I'm not at the remote
> (Baltimore) site, but I can VPN in and see the router. Is there
> something physical that could be causing this? (bad cable, etc) Or is
> it a config thing? I've confirmed the DLCI and timeslots. I'm getting
> A LOT of heat to get this fixed and I'm out of ideas!!!
>
> I'm including the interface config on the 1720 and a sho int0
>
> interface Serial0
> bandwidth 256
> no ip address
> encapsulation frame-relay IETF
> service-module t1 timeslots 1-4
> frame-relay lmi-type ansi
> !
> interface Serial0.1 point-to-point
> ip address 192.168.253.250 255.255.255.0
> frame-relay interface-dlci 16 IETF
>
> bal-den#sho int s0
> Serial0 is up, line protocol is up
> Hardware is PQUICC with Fractional T1 CSU/DSU
> MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation FRAME-RELAY IETF, loopback not set
> Keepalive set (10 sec)
> LMI enq sent 14905, LMI stat recvd 14295, LMI upd recvd 0, DTE LMI
> up
> LMI enq recvd 608, LMI stat sent 0, LMI upd sent 0
> LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
> Broadcast queue 0/64, broadcasts sent/dropped 6460/0, interface
> broadcasts 5155
> Last input 00:00:00, output 00:00:02, output hang never
> Last clearing of "show interface" counters 1d17h
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/2/256 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 29265 packets input, 283193 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 2 giants, 0 throttles
> 150 input errors, 34 CRC, 67 frame, 0 overrun, 0 ignored, 48 abort
> 35341 packets output, 1974602 bytes, 0 underruns
> 0 output errors, 0 collisions, 202 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 5 carrier transitions
> DCD=up DSR=up DTR=up RTS=up CTS=up
>
> bal-den#sho int s0.1
> Serial0.1 is up, line protocol is up
> Hardware is PQUICC with Fractional T1 CSU/DSU
> Internet address is 192.168.253.250/24
> MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation FRAME-RELAY IETF
>


Post a "show frame-relay pvc"


 
Reply With Quote
 
 
 
 
Todd
Guest
Posts: n/a
 
      10-06-2005
sho frame pv

PVC Statistics for interface Serial0 (Frame Relay DTE)

Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0

DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
Serial0.1

input pkts 15050 output pkts 21493 in bytes 65356
out bytes 1837181 dropped pkts 9 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 6709 out bcast bytes 681071
pvc create time 1d19h, last time pvc status changed 17:14:54

Heres a sho frame-relay lmi
sho frame pvc

PVC Statistics for interface Serial0 (Frame Relay DTE)

Active Inactive Deleted Static
Local 1 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0

DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
Serial0.1

input pkts 15056 output pkts 21495 in bytes 65380
out bytes 1837293 dropped pkts 9 in FECN pkts 0
in BECN pkts 0 out FECN pkts 0 out BECN pkts 0
in DE pkts 0 out DE pkts 0
out bcast pkts 6711 out bcast bytes 681183
pvc create time 1d19h, last time pvc status changed 17:16:03

 
Reply With Quote
 
Igor Mamuzic
Guest
Posts: n/a
 
      10-06-2005
Have you tried to change LMI type? post 'debug frame lmi' output...

Also, you may have FR encapsulation mismatch... Is FR encapsulation equal to
the both DTE's in your FR network?
Also, is the link flapping? (up/down line protocol status changing couple of
times) ? I see a lot of interface errors comparing to the fact that there is
no "real" application traffic passing trough your serial interface since FR
isn't working...Also, I noticed that you don't get LMI stat recvd for each
LMI enq sent... But I don't suspect your line quality since if it is the
case then you would had partial succes for your ping... Of course, IP config
is ok for both sides?

Try above changes and let mi know the results...

B.R.
Igor



"Todd" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed) ps.com...
> I'm ABSOLUTLEY STUMPED!!! I desperately need help.
> I have a frame relay line going from out main office "Denver" to a
> remote site "Baltimore"
>
> My Cisco 1720 interfaces all show UP/UP status and shows LMI, but from
> its console I can't ping the Serial0.1 interface (192.168.253.250)
>
> On the Motorola, the config looks good and from its console I can ping
> its Serial (192.168.253.249) and it sees the circuit and everything
> looks good. It CAN'T see 192.168.253.250 though.
>
> Whats wrong? I spent about an hour yesterday on the phone with
> Motorola and everything looks good on that end. And as far as I know,
> the Cisco looks right. Am I missing something? I'm not at the remote
> (Baltimore) site, but I can VPN in and see the router. Is there
> something physical that could be causing this? (bad cable, etc) Or is
> it a config thing? I've confirmed the DLCI and timeslots. I'm getting
> A LOT of heat to get this fixed and I'm out of ideas!!!
>
> I'm including the interface config on the 1720 and a sho int0
>
> interface Serial0
> bandwidth 256
> no ip address
> encapsulation frame-relay IETF
> service-module t1 timeslots 1-4
> frame-relay lmi-type ansi
> !
> interface Serial0.1 point-to-point
> ip address 192.168.253.250 255.255.255.0
> frame-relay interface-dlci 16 IETF
>
> bal-den#sho int s0
> Serial0 is up, line protocol is up
> Hardware is PQUICC with Fractional T1 CSU/DSU
> MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation FRAME-RELAY IETF, loopback not set
> Keepalive set (10 sec)
> LMI enq sent 14905, LMI stat recvd 14295, LMI upd recvd 0, DTE LMI
> up
> LMI enq recvd 608, LMI stat sent 0, LMI upd sent 0
> LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
> Broadcast queue 0/64, broadcasts sent/dropped 6460/0, interface
> broadcasts 5155
> Last input 00:00:00, output 00:00:02, output hang never
> Last clearing of "show interface" counters 1d17h
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/2/256 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 29265 packets input, 283193 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 2 giants, 0 throttles
> 150 input errors, 34 CRC, 67 frame, 0 overrun, 0 ignored, 48 abort
> 35341 packets output, 1974602 bytes, 0 underruns
> 0 output errors, 0 collisions, 202 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 5 carrier transitions
> DCD=up DSR=up DTR=up RTS=up CTS=up
>
> bal-den#sho int s0.1
> Serial0.1 is up, line protocol is up
> Hardware is PQUICC with Fractional T1 CSU/DSU
> Internet address is 192.168.253.250/24
> MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation FRAME-RELAY IETF
>



 
Reply With Quote
 
Todd
Guest
Posts: n/a
 
      10-07-2005
I do a "debug frame lmi" and I get this:
Frame Relay LMI debugging is on
Displaying all Frame Relay LMI data

Thats it.
I rebooted yesterday afternoon and the lmi #'s look like this now:

Num Status Enq. Sent 7254 Num Status msgs Rcvd 7251
Num Update Status Rcvd 0 Num Status Timeouts 3

Here's what I've got for the interfaces:
interface Serial0
bandwidth 256
no ip address
encapsulation frame-relay IETF
service-module t1 timeslots 1-4
frame-relay lmi-type ansi
!
interface Serial0.1 point-to-point
ip address 192.168.253.250 255.255.255.0
no cdp enable
frame-relay interface-dlci 16 IETF

The motorola on the other side of the circuit is 192.168.253.249 and
can ping itself.

I'm still not convinced that theres not something wrong with the
Motorola to Cisco connection. The Motorola is an old Vanguard running
5.3 software.
I've got another Vanguard here that if I could get it configured, I'd
send it out to Baltimore to check, but I can't even get to a console on
the dang thing, anybody know what emulation Motorola uses?

 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
help configuring cisco 2600 for frame-relay tony_gio@hotmail.com Cisco 3 07-08-2008 06:57 PM
Dhcp Relay Agent And Acl On Sw 3750, DHCP Relay Agent and ACL on Sw 3750 Vimokh Cisco 3 09-06-2006 02:16 AM
convention for frame relay diagrams - cross posted from alt.certification.cisco John Smith Cisco 2 03-13-2005 04:14 PM
Cisco 1601 as Central Site Router for Frame Relay? Tobias Skytte Cisco 0 11-25-2004 01:06 PM
How do i configure a cisco 2500 router with Frame-Relay and NAT Jared Timmerman Cisco 2 10-30-2004 01:51 AM



Advertisments