Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > Configuration of Cisco Router for use on a DS3 microwave circuit

Reply
Thread Tools

Configuration of Cisco Router for use on a DS3 microwave circuit

 
 
cybereel
Guest
Posts: n/a
 
      10-05-2006
My organisation currently has a wide area network configured as a ring,
using our own microwave equipment. The network runs two seperate DS3
circuits. At each location, there is a Lucent AP-1000 with LMC 5245 DS3
Wan Adapter which converts to Ethernet and provide each lan with
ethernet service. This network works fine. I am now attempting to add
another site using a cisco 3800 router with two (2) NM-1T3 interface
cards. My challenge is that the circuit has a numerous amount of
errors. The section below highlights the configurations and errors.

All AP-1000 routers
Interface: t3
MTU: 4470
Clocking: Internal
Crc mode: crc16
Type mode: ds3
Line type:dsx3Cbit Parity
Line length: 100
Line coding: dsx3B3ZS
SendCode: dsx3SendNoCode
Clock source: internal
ScramblingMOde: dsx3Cisco

The new Cisco 3800 router with NM-1T3
controller T3 1/0
cablelength 100

interface s1/0
ip address x.x.x.x 255.255.255.0
ip route-cach flow
dsu badnwidth 44210

On executing the sh int s1/0 command the follwoing is found
Serial1/0 is up, line protocol is up
Hardware ss DSXPNM Serial
.......
Encapsulation HDLC, crc 16
......
163959228 input errors, 163959228 CRC, 72386460 frame, 43881477
overrun, 0 ignored, 122414945 abort.
DSU mode 0, bandwidth 44210, real bandwidth 44210, scramble 0

On executing the sh controller s1/0 command the follwoing is found
T3 1/0 is up
Applique type subrate T3
No alarms detected
MDL tranmission disabled
Framing is C-bit Parity, Line code is B3ZS, CLock source internal
Everything else is 0.

My Microwave manual provides the following Information on DS3 interface

Data Rate - Asynchronous 44.736Mb/s +- 20ppm
Line Code - B3ZS
Input - +5.7 to -1.8 dBm at DSX-3 Cross connect attenuated by up to
450ft of cable
Output - +1 to +4 dBm, LBO out , 0 to +3 dBm, LBO in (measured all-1s
unframed)
Pulse Shape - TR-TSY-000499 complaint
Impedence - 75 ohms, nominal (10 to 50 MHz)


These are my challenges:-
1 - Am I using the right interface card and router?
2 - Am I missing a configuration somewhere?
3 - Are there compatability issues between the two routers?

I tried the following(individually, not all at once:-
1 - Changing the modes of the dsu - result - line protocol switch to
down
2 - Changing scrambling - result - line protocol switch to down
3 - Changing CLock source to line - result - no change in errors
4 - Changed the parity - line protocol switch to down

I am at a complete loss.

Look forward to your responses. Thank You

 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
RE: Cisco Router for BGP and DS3, Admin Distance M Cisco 1 01-14-2008 12:23 PM
Cisco Router for BGP and DS3 M Cisco 9 01-07-2008 02:08 AM
Need Advice: Coonecting a 7206 with PA2t3 to a ds3 circuit with 2 pvc's jds Cisco 0 06-24-2005 01:08 PM
backup circuit configuration with cisco Jog Dial Cisco 3 08-16-2004 07:18 PM
Suggestions for DS3 router options Adrian Jensen Cisco 3 07-11-2003 05:19 AM



Advertisments