Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > Network command

Reply
Thread Tools

Network command

 
 
lrantisi@gmail.com
Guest
Posts: n/a
 
      09-05-2006
I am using the EIGRP protocol, I have a router that has its ports with
the following IP addresses(10.2.3.4 , 10.2.3.5 , 10.2.3.6)
What would be better for the network command, that is used in the EIGRP
configuration,

(Network 10.2.3.0 )
or the
(Network 10.0.0.0)

OK, now what if the port IP addresses of the router were
(190.186.2.3 , 190.186.2.4 , 190.186.2.5)
will it be
(Network 190.168.2.0)
or the
(Network 190.0.0.0)

Did you get my idea, I mean: should we use the smallest or the biggest
network range inside the network command, and is there any difference
when the network type is A, B or C.

 
Reply With Quote
 
 
 
 
Merv
Guest
Posts: n/a
 
      09-05-2006

The network statement is used to enable EIGRP on router interfaces.

Generally a classful network would be specified althought the EIGRP
statement now also accepts a mask

for example

network 10.0.0.0 ! typical usage - all 10.x.x.x interfaces will be
enabled for EIGRP

network 10.1.0.0 255.255.0.0 ! only interface will 10.1.x.x will be
enabled

 
Reply With Quote
 
 
 
 
jw
Guest
Posts: n/a
 
      09-05-2006
As above plus you can't assign 10.2.3.4 and 10.2.3.5 to different interfaces
on the router with the same mask since they overlap.
(unless they are like loopbacks with /32 masks)

"Merv" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed) oups.com...
>
> The network statement is used to enable EIGRP on router interfaces.
>
> Generally a classful network would be specified althought the EIGRP
> statement now also accepts a mask
>
> for example
>
> network 10.0.0.0 ! typical usage - all 10.x.x.x interfaces will be
> enabled for EIGRP
>
> network 10.1.0.0 255.255.0.0 ! only interface will 10.1.x.x will be
> enabled
>



 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pix command to allow access to network behind a network elementaladmins@gmail.com Cisco 2 08-11-2007 08:31 PM
NCQ (Native Command Queuing) and TCQ (Tagged Command Queuing) Explained Silverstrand Front Page News 0 04-17-2006 05:49 PM
Need simple command for validating xml files at the command line Bernd Oninger XML 1 07-07-2004 06:20 PM
RUN/execute a Command-Line command from an ASP page. Lucas Cowald ASP .Net 4 10-23-2003 11:09 AM
copying value of DDL in a Datagrid "pre-edit command" to value in "post edit command" San Diego Guy ASP .Net 0 08-07-2003 08:59 PM



Advertisments