Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > Cisco > VoIP - PRI between Definity G3 and 2611 Gateway

Reply
Thread Tools

VoIP - PRI between Definity G3 and 2611 Gateway

 
 
Rob
Guest
Posts: n/a
 
      11-30-2004
Hi,

I am having trouble getting a PRI up between an Avaya Definity G3 PBX
and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
shows "up up".

My gateway is registered with CallManager just fine, but I'm pretty
sure this is simply an ISDN issue. I have the PBX setup as ISDN "user"
side and the 2611 as ISDN "network" side. We are using National/NI2.
The Definity is configured as Country code 1, Protocol version a. Does
anyone know if this is correct? Also, should the "Connect" version on
the PBX be "pbx" or "line-side"??

When I do a "show isdn status" the Layer 2 state of "TEI_ASSIGNED" is
a problem in my mind - I think this should be
"MULTIPLE_FRAME_ESTABLISHED."

Thanks - Rob.


Gateway1#sho isdn status
Global ISDN Switchtype = primary-ni

%Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
apply

ISDN Serial1/0:23 interface
******* Network side configuration *******
dsl 0, interface ISDN Switchtype = primary-ni
L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x807FFFFF
Number of L2 Discards = 0, L2 Session ID = 94
Gateway1#
Gateway1#
Gateway1#
Gateway1#sho ip int brief
Interface IP-Address OK? Method Status
Prot
ocol
FastEthernet0/0 10.10.4.50 YES NVRAM up
up

FastEthernet0/1 10.10.5.50 YES NVRAM up
up

Serial1/0:0 unassigned YES unset down
down

Serial1/0:1 unassigned YES unset down
down

Serial1/0:2 unassigned YES unset down
down

(snip)

Serial1/0:21 unassigned YES unset down
down

Serial1/0:22 unassigned YES unset down
down

Serial1/0:23 unassigned YES NVRAM up
up
Gateway1#
Gateway1#
Gateway1#sho run

(some non-relevant config snipped)

!
network-clock-participate slot 1
no network-clock-participate wic 0
network-clock-select 1 T1 1/0
network-clock-select 2 T1 1/1
!
isdn switch-type primary-ni
voice-card 1
!
ccm-manager redundant-host 10.219.16.1
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 10.219.16.1
ccm-manager config
!
!
controller T1 1/0
framing esf
fdl att
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
interface Serial1/0:23
no ip address
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
voice-port 1/0:23
!
mgcp
mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
!
dial-peer voice 1 pots
application mgcpapp
port 1/0:23
!
 
Reply With Quote
 
 
 
 
Brian LaVallee
Guest
Posts: n/a
 
      12-03-2004
This may get you closer to what you want. I have a PRI on a 3620.

Brian LaVallee

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-IS-M), Version 12.3(1a), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 05-Jun-03 17:53 by dchih
Image text-base: 0x60008950, data-base: 0x6187C000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

Router uptime is 10 weeks, 23 hours, 56 minutes
System returned to ROM by power-on
System image file is "flash:c3620-is-mz.123-1a.bin"

cisco 3620 (R4700) processor (revision 0x81) with 59392K/6144K bytes of
memory.
Processor board ID 25119094
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 Channelized T1/PRI port(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=


Current configuration : 1646 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Hostname
!
boot system flash c3620-is-mz.123-9.bin
enable secret 5 xXxXxXxXxXxXxXxXxXxXxXxXxXxXxXxX
enable password xXxXxXxX
!
voice-card 1
!
ip subnet-zero
!
ip name-server NNN.NNN.NNN.NNN
!
isdn switch-type primary-ni
isdn voice-call-failure 0
!
voice hunt user-busy
voice call carrier capacity active
!
voice service voip
signaling forward unconditional
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
sip
!
voice class codec 99
codec preference 1 g711ulaw
codec preference 2 g729r8
!
no voice hpi capture buffer
no voice hpi capture destination
!
controller T1 1/0
framing sf
linecode ami
!
interface FastEthernet0/0
ip address NNN.NNN.NNN.NNN 255.255.255.240
speed auto
full-duplex
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 NNN.NNN.NNN.NNN
!
dialer-list 1 protocol ip permit
!
dial-peer cor custom
!
dial-peer voice 1 voip
huntstop
preference 2
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 99
session protocol sipv2
dtmf-relay rtp-nte
no vad
!
dial-peer voice 2 pots
preference 2
application session
destination-pattern ..........
translate-outgoing called 300
no digit-strip
direct-inward-dial
forward-digits all
!
sip-ua
retry invite 2
retry response 3
retry bye 3
retry prack 6
timers expires 300000
sip-server ipv4:NNN.NNN.NNN.NNN
no transport tcp
!
line con 0
logging synchronous
line aux 0
line vty 0 4
password 7 xXxXxXxXxXxXxX
logging synchronous
login
!
end

"Rob" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed) om...
> Hi,
>
> I am having trouble getting a PRI up between an Avaya Definity G3 PBX
> and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
> crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
> shows "up up".
>
> My gateway is registered with CallManager just fine, but I'm pretty
> sure this is simply an ISDN issue. I have the PBX setup as ISDN "user"
> side and the 2611 as ISDN "network" side. We are using National/NI2.
> The Definity is configured as Country code 1, Protocol version a. Does
> anyone know if this is correct? Also, should the "Connect" version on
> the PBX be "pbx" or "line-side"??
>
> When I do a "show isdn status" the Layer 2 state of "TEI_ASSIGNED" is
> a problem in my mind - I think this should be
> "MULTIPLE_FRAME_ESTABLISHED."
>
> Thanks - Rob.
>
>
> Gateway1#sho isdn status
> Global ISDN Switchtype = primary-ni
>
> %Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
> apply
>
> ISDN Serial1/0:23 interface
> ******* Network side configuration *******
> dsl 0, interface ISDN Switchtype = primary-ni
> L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x807FFFFF
> Number of L2 Discards = 0, L2 Session ID = 94
> Gateway1#
> Gateway1#
> Gateway1#
> Gateway1#sho ip int brief
> Interface IP-Address OK? Method Status
> Prot
> ocol
> FastEthernet0/0 10.10.4.50 YES NVRAM up
> up
>
> FastEthernet0/1 10.10.5.50 YES NVRAM up
> up
>
> Serial1/0:0 unassigned YES unset down
> down
>
> Serial1/0:1 unassigned YES unset down
> down
>
> Serial1/0:2 unassigned YES unset down
> down
>
> (snip)
>
> Serial1/0:21 unassigned YES unset down
> down
>
> Serial1/0:22 unassigned YES unset down
> down
>
> Serial1/0:23 unassigned YES NVRAM up
> up
> Gateway1#
> Gateway1#
> Gateway1#sho run
>
> (some non-relevant config snipped)
>
> !
> network-clock-participate slot 1
> no network-clock-participate wic 0
> network-clock-select 1 T1 1/0
> network-clock-select 2 T1 1/1
> !
> isdn switch-type primary-ni
> voice-card 1
> !
> ccm-manager redundant-host 10.219.16.1
> ccm-manager mgcp
> ccm-manager music-on-hold
> ccm-manager config server 10.219.16.1
> ccm-manager config
> !
> !
> controller T1 1/0
> framing esf
> fdl att
> linecode b8zs
> pri-group timeslots 1-24 service mgcp
> !
> interface Serial1/0:23
> no ip address
> isdn switch-type primary-ni
> isdn protocol-emulate network
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> no cdp enable
> !
> voice-port 1/0:23
> !
> mgcp
> mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
> !
> dial-peer voice 1 pots
> application mgcpapp
> port 1/0:23
> !



 
Reply With Quote
 
 
 
 
mbawa
Guest
Posts: n/a
 
      02-01-2005
Hi,

I am planning to inegrate a Definity PBX with a 2611 router .Can you send
me the config for Definity and where should I port the PRI on Definity ?

Thanks,
Mike

-------------------------------------
Rob wrote:


> Hi,


> I am having trouble getting a PRI up between an Avaya Definity G3 PBX
> and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
> crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
> shows "up up".


> My gateway is registered with CallManager just fine, but I'm pretty
> sure this is simply an ISDN issue. I have the PBX setup as ISDN
> "user"
> side and the 2611 as ISDN "network" side. We are using
> National/NI2.
> The Definity is configured as Country code 1, Protocol version a. Does
> anyone know if this is correct? Also, should the "Connect"
> version on
> the PBX be "pbx" or "line-side"??


> When I do a "show isdn status" the Layer 2 state of
> "TEI_ASSIGNED" is
> a problem in my mind - I think this should be
> "MULTIPLE_FRAME_ESTABLISHED."


> Thanks - Rob.



> Gateway1#sho isdn status
> Global ISDN Switchtype = primary-ni


> %Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
> apply


> ISDN Serial1/0:23 interface
> ******* Network side configuration *******
> dsl 0, interface ISDN Switchtype = primary-ni
> L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x807FFFFF
> Number of L2 Discards = 0, L2 Session ID = 94
> Gateway1#
> Gateway1#
> Gateway1#
> Gateway1#sho ip int brief
> Interface IP-Address OK? Method Status
> Prot
> ocol
> FastEthernet0/0 10.10.4.50 YES NVRAM up
> up


> FastEthernet0/1 10.10.5.50 YES NVRAM up
> up


> Serial1/0:0 unassigned YES unset down
> down


> Serial1/0:1 unassigned YES unset down
> down


> Serial1/0:2 unassigned YES unset down
> down


> (snip)


> Serial1/0:21 unassigned YES unset down
> down


> Serial1/0:22 unassigned YES unset down
> down


> Serial1/0:23 unassigned YES NVRAM up
> up
> Gateway1#
> Gateway1#
> Gateway1#sho run


> (some non-relevant config snipped)


> !
> network-clock-participate slot 1
> no network-clock-participate wic 0
> network-clock-select 1 T1 1/0
> network-clock-select 2 T1 1/1
> !
> isdn switch-type primary-ni
> voice-card 1
> !
> ccm-manager redundant-host 10.219.16.1
> ccm-manager mgcp
> ccm-manager music-on-hold
> ccm-manager config server 10.219.16.1
> ccm-manager config
> !
> !
> controller T1 1/0
> framing esf
> fdl att
> linecode b8zs
> pri-group timeslots 1-24 service mgcp
> !
> interface Serial1/0:23
> no ip address
> isdn switch-type primary-ni
> isdn protocol-emulate network
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> no cdp enable
> !
> voice-port 1/0:23
> !
> mgcp
> mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
> !
> dial-peer voice 1 pots
> application mgcpapp
> port 1/0:23
> !






##-----------------------------------------------#
Article posted with Cabling-Design.com Newsgroup Archiv
http://www.cabling-design.com/forum
no-spam read and post WWW interface to your favorite newsgroup -
comp.dcom.sys.cisco,comp.dcom.voice-over-ip - messages and counting
##-----------------------------------------------##
 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
PRI and digital modem modules for 2611 Sanal Kisi Cisco 7 05-01-2006 04:26 AM
PRI b-channel LCKO problem between Cisco VOIP Gateway and Nortel 61C CAsniffer@yahoo.com VOIP 1 05-01-2005 02:43 PM
PRI b-channel LCKO problem between Cisco VOIP Gateway and Nortel 61C CAsniffer@yahoo.com Cisco 0 04-20-2005 05:15 PM
VoIP - PRI between Definity G3 and 2611 Gateway Rob VOIP 2 02-01-2005 11:25 PM
Atlas 550 PRI to Cisco 3620 Channelized PRI port problem jamal Cisco 1 07-25-2003 02:51 PM



Advertisments