finished ccie, selling gear

garnet
613.740.5949 x8023 (M-F 7-3)


1 x Cisco 1750-2v ($675US = $877Can)
- 48M RAM
- 8M Flash
- use for practicing voip
- built in DSP (hence the 2v designation) to accomodate voice (VIC)
modules - VIC-2FXS voice module- provides 2 RJ11 POTS lines - plug in
any old analog phone
- WIC-1T serial port module - provides 1 DB-60 serial interface
- WIC-1B-U ISDN module - provides 1 ISDN U interface

1 x Cisco 1750-2v ($650US = $845Can)
- 32M RAM
- 8M Flash
- use for practicing voip
- built in DSP (hence the 2v designation) to accomodate voice (VIC) modules
- VIC-2FXS voice module- provides 2 RJ11 POTS lines
- WIC-1T serial port module - provides 1 DB-60 serial interface
- WIC-1B-U ISDN module - provides 1 ISDN U interface

1 x Cisco 4500m ($530US = $689Can)
- 48M RAM (max)
- 16M Flash (max)
- NP-2T serial port module - provides 2 DB-60 interfaces
- NP-1A-SM ATM single-mode module - provides 1 ATM SM
(short reach) OC3 interface
- NP-2E ethernet module - provides 2 10Mb ethernet interfaces

1 x Cisco 4500m ($500US = $650Can)
- 48M RAM (max)
- 4M Flash
- new flash is available on ebay at ~ $10US / 8MB
- best bet is just to boot from tftp
- NP-2T serial port module - provides 2 DB-60 interfaces
- NP-1A-MM ATM multi-mode module - provides 1 ATM MM OC3 interface
- NP-6E ethernet module - provides 6 10Mb ethernet interfaces
- basically this is sold at the cost of the interface modules with a free
router included - I've done this because of the low 4M Flash in this unit

1 x Bay Networks Centillion 100 ($200US = $260Can)
- atm switch
- 2 x ATM OC3 Single Mode ports
- 2 x ATM OC3 Multi Mode ports
- includes extra MDA card (processor module)
- provides svc and pvc support (including classical IP)
- supports ILMI, UNI 3.0/3.1
- includes 40 ports of switched fast ethernet
- preconfigured with some PVCs so requires no further config - plug in and go
- includes windows gui (yes, a gui) to configure more PVCs,
change UNI etc. if necessary
- fraction of the price of an equivalent Cisco Lightstream 1010 (~$1250US)
- CCIE exam blueprint specifies that no config of switch is required for
exam, only config of routers connected to ATM network
- if purchased with 4500s above will include multimode and singlemode fiber

1 x Teltone ILS-B-01 ISDN Simulator ($500US = $650Can)
- 2 x ISDN U interfaces
- simulates an ISDN network allowing router to router ISDN calls
- can be managed remotely through serial interface
- preconfigured - plug in routers and go
- includes windows GUI to modify config if desired
- includes manual and diskette
- purchased new 2 years ago

Bundles:
ATM Bundle
- 2 x 4500m routers + 1 x Centillion 100 (all as per above)
- includes multimode and singlemode fiber
- plus 1 NP-8B 8 port ISDN BRI module
- $1450Can

ISDN/Voice Bundle
- 2 x 1750-2v + 1 x Teltone ISDN Simulator (all as per above)
- $2150Can

Whole Works Bundle
- everything as per individual equipment above
- plus 1 NP-8B 8 port ISDN BRI module for 4500m router
- plus 10 Cat5 cables
- plus 2 cat5 crossover cables
- plus 2 db50 to db60 crossover dce-dte serial cables (for
connecting 4500 to 1750/2500)
- plus Cisco Press Practical Studies Volume 1
- plus 2 x catalyst 1924 ethernet switches (value ~100Can each)
- some technical support from CCIE#11928 to get it all up and working
- $3399Can

Everything is working to the best of my knowledge and all may
be tried via ssh.
All equipment is guaranteed not DOA. Except for DOA, no other
returns (finished my ccie, I don't need this stuff anymore!).

selling cisco

What materials did you use to pass the CCIE Voice written? I nned to
PASS this test in the next week or so. URGENT advise needed! Thx.-
Reply to

WCS