«

Hello people I am having this output (see log) when I reboot a Catalyst 2950.
Can anyone explain me the interpretation of this error?


Saludos,
Victor Cappuccio

Switch#show logging
Syslog logging: enabled (0 messages dropped, 0 flushes, 0 overruns)
Console logging: level debugging, 49 messages logged
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 49 messages logged
File logging: disabled
Trap logging: level informational, 71 message lines logged

Log Buffer (4096 bytes):
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:11: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:12: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD
cmic_schan_op ERROR: timeout (OP=0xD polls=100000)

00:00:13: %STRATA-3-SCHAN_OP_FAILURE:
S-channel operation timeout for opcode WRITE_REG_CMD

In article < >,
says...
> STRATA-3-SCHAN_OP_FAILURE
>

from CCO:

<CCO>
%STRATA-3-SCHAN_OP_FAILURE : \n S-channel operation timeout for opcode
[chars]\n

Explanation A read or writer operation to the ASIC registers or
memories has failed. This condition was caused by due to an ASIC
internal bus failure. This condition prevents the switch from being used
correctly. If this message occurs extensively on the switch, it could be
caused by an ASIC or hardware failure.

Recommended Action Replace the ASIC.
</CCO>

-Ivan.