«

I recently purchased a Cisco 806 router and am attempting to configure
both vpn tunneling and SSH. When I try to enter the "crypto" command
or "ip ssh" command, they are not valid. I am fairly certain that I
have the IOS which supports IPSEC 3DES which should in turn support
SSH functionality. Posted is my "show version":

00:27:53: %SYS-5-CONFIG_I: Configured from console by console
Cisco Internetwork Operating System Software
IOS (tm) C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY
DEPLOYMENT RELEA
SE SOFTWARE (fc1)
Synched to technology version 12.2(7.1)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 23-May-02 22:34 by ealyon
Image text-base: 0x80013170, data-base: 0x807432E4

ROM: System Bootstrap, Version 12.2(4r)XM3, RELEASE SOFTWARE (fc1)
ROM: C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY DEPLOYMENT
RELEASE S
OFTWARE (fc1)

cyclops uptime is 27 minutes
System returned to ROM by reload
System image file is "flash:c806-o3sy6-mz.122-4.YH.bin"

CISCO C806 (MPC855T) processor (revision 0x501) with 30720K/2048K
bytes of memor
y.
Processor board ID FOC07010F5R (3319105503), with hardware revision
0000
CPU rev number 0
Bridging software.
2 Ethernet/IEEE 802.3 interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

Configuration register is 0x2102


Any help on this issue would be greatly appreciated.

-Brad

No, your router doesn't have a crypto image. You need to have a
c806-k9o3sy6-mz image. -k9- stands for 3DES image and -k8- stands for DES.

Ravikumar

"Brad B." wrote:

> I recently purchased a Cisco 806 router and am attempting to configure
> both vpn tunneling and SSH. When I try to enter the "crypto" command
> or "ip ssh" command, they are not valid. I am fairly certain that I
> have the IOS which supports IPSEC 3DES which should in turn support
> SSH functionality. Posted is my "show version":
>
> 00:27:53: %SYS-5-CONFIG_I: Configured from console by console
> Cisco Internetwork Operating System Software
> IOS (tm) C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY
> DEPLOYMENT RELEA
> SE SOFTWARE (fc1)
> Synched to technology version 12.2(7.1)T
> TAC Support: http://www.cisco.com/tac
> Copyright (c) 1986-2002 by cisco Systems, Inc.
> Compiled Thu 23-May-02 22:34 by ealyon
> Image text-base: 0x80013170, data-base: 0x807432E4
>
> ROM: System Bootstrap, Version 12.2(4r)XM3, RELEASE SOFTWARE (fc1)
> ROM: C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY DEPLOYMENT
> RELEASE S
> OFTWARE (fc1)
>
> cyclops uptime is 27 minutes
> System returned to ROM by reload
> System image file is "flash:c806-o3sy6-mz.122-4.YH.bin"
>
> CISCO C806 (MPC855T) processor (revision 0x501) with 30720K/2048K
> bytes of memor
> y.
> Processor board ID FOC07010F5R (3319105503), with hardware revision
> 0000
> CPU rev number 0
> Bridging software.
> 2 Ethernet/IEEE 802.3 interface(s)
> 128K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read/Write)
> 2048K bytes of processor board Web flash (Read/Write)
>
> Configuration register is 0x2102
>
> Any help on this issue would be greatly appreciated.
>
> -Brad

I went ahead and upgraded to the k9 image and now have full 3DES and
ssh functionality. Thank you.

Ravikumar Eswaran <> wrote in message news:<>...
> No, your router doesn't have a crypto image. You need to have a
> c806-k9o3sy6-mz image. -k9- stands for 3DES image and -k8- stands for DES.
>
> Ravikumar
>
> "Brad B." wrote:
>
> > I recently purchased a Cisco 806 router and am attempting to configure
> > both vpn tunneling and SSH. When I try to enter the "crypto" command
> > or "ip ssh" command, they are not valid. I am fairly certain that I
> > have the IOS which supports IPSEC 3DES which should in turn support
> > SSH functionality. Posted is my "show version":
> >
> > 00:27:53: %SYS-5-CONFIG_I: Configured from console by console
> > Cisco Internetwork Operating System Software
> > IOS (tm) C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY
> > DEPLOYMENT RELEA
> > SE SOFTWARE (fc1)
> > Synched to technology version 12.2(7.1)T
> > TAC Support: http://www.cisco.com/tac
> > Copyright (c) 1986-2002 by cisco Systems, Inc.
> > Compiled Thu 23-May-02 22:34 by ealyon
> > Image text-base: 0x80013170, data-base: 0x807432E4
> >
> > ROM: System Bootstrap, Version 12.2(4r)XM3, RELEASE SOFTWARE (fc1)
> > ROM: C806 Software (C806-O3SY6-M), Version 12.2(4)YH, EARLY DEPLOYMENT
> > RELEASE S
> > OFTWARE (fc1)
> >
> > cyclops uptime is 27 minutes
> > System returned to ROM by reload
> > System image file is "flash:c806-o3sy6-mz.122-4.YH.bin"
> >
> > CISCO C806 (MPC855T) processor (revision 0x501) with 30720K/2048K
> > bytes of memor
> > y.
> > Processor board ID FOC07010F5R (3319105503), with hardware revision
> > 0000
> > CPU rev number 0
> > Bridging software.
> > 2 Ethernet/IEEE 802.3 interface(s)
> > 128K bytes of non-volatile configuration memory.
> > 8192K bytes of processor board System flash (Read/Write)
> > 2048K bytes of processor board Web flash (Read/Write)
> >
> > Configuration register is 0x2102
> >
> > Any help on this issue would be greatly appreciated.
> >
> > -Brad