Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > VOIP > Configure ATA 186 for use with ALTIGEN system

Reply
Thread Tools

Configure ATA 186 for use with ALTIGEN system

 
 
rodman
Guest
Posts: n/a
 
      04-11-2005
I have an ALTIGEN 5.0 phone system with IP extensions only. So I want
to use the ATA 186 and hook up a fax machine.

I bought an ATA from CISCO and got the H323 image loaded but now i am
stuck. I have no clue how to configure the zillion parameters so the
altigen system recognizes the device. Altigen support have not been
much help.

Has anyone done this ? any help appreciated.

Rodman

 
Reply With Quote
 
 
 
 
Brad
Guest
Posts: n/a
 
      05-24-2005
I am in the same boat. I don't have the Altigen VoIP card installed yet,
but I am gearing up for it. The technician is installing the card
tomorrow. I have 2 Cisco ATA 186 boxes ready to configure.

So far I have configured the two boxes with the latest h.323 image (3.1.2)
and assigned static IP addresses (for testing). I then went into the
config page (http://ww.xx.yy.zz/dev) and set the UID0 field as 4000 on one
box, and 4001 on the other. I am able to call the other phone directly
using the following syntax: 4001**w*x*y*z# where wxyz represents the ip
address.

The next step is to configure the boxes to register with the altigen
server as the gatekeeper and gateway.

Hope this helps. Share your experiences too! I am still working on this.

-Brad

-------------------------------------
rodman wrote:




> I have an ALTIGEN 5.0 phone system with IP extensions only. So I want
> to use the ATA 186 and hook up a fax machine.


> I bought an ATA from CISCO and got the H323 image loaded but now i am
> stuck. I have no clue how to configure the zillion parameters so the
> altigen system recognizes the device. Altigen support have not been
> much help.


> Has anyone done this ? any help appreciated.


> Rodman







##-----------------------------------------------#
Article posted with Cabling-Design.com Newsgroup Archiv
http://www.cabling-design.com/forum
no-spam read and post WWW interface to your favorite newsgroup -
comp.dcom.voice-over-ip - 3998 messages and counting
##-----------------------------------------------##
 
Reply With Quote
 
 
 
 
brjsm
Guest
Posts: n/a
 
      05-24-2005

I am in the same boat. I don't have the Altigen VoIP card installe
yet,
but I am gearing up for it. The technician is installing the card
tomorrow. I have 2 Cisco ATA 186 boxes ready to configure.

So far I have configured the two boxes with the latest h.323 imag
(3.1.2)
and assigned static IP addresses (for testing). I then went into the
config page (http://ww.xx.yy.zz/dev) and set the UID0 field as 4000 o
one
box, and 4001 on the other. I am able to call the other phone directly
using the following syntax: 4001**w*x*y*z# where wxyz represents th
ip
address.

The next step is to configure the boxes to register with the altigen
server as the gatekeeper and gateway.

Hope this helps. Share your experiences too! I am still working o
this.

-Brad


rodman Wrote:
> I have an ALTIGEN 5.0 phone system with IP extensions only. So I want
> to use the ATA 186 and hook up a fax machine.
>
> I bought an ATA from CISCO and got the H323 image loaded but now i am
> stuck. I have no clue how to configure the zillion parameters so the
> altigen system recognizes the device. Altigen support have not been
> much help.
>
> Has anyone done this ? any help appreciated.
>
> Rodma


--
brjsm
 
Reply With Quote
 
brjsm
Guest
Posts: n/a
 
      06-01-2005

I have successfully set up the Altigen VoIP card, and I have 2 altige
IP phones that can make and receive calls. I have successfull
registered the Cisco ATA 186 with the Altigen system as the gatekeeper
The Cisco ATA box can make calls to just about anywhere, but it canno
receive calls from anywhere. I have .cap files from ethereal and lo
files from debug mode (cisco's prserv.exe debug tool). If anyone i
interested in this issue, let me know at http://www.velocityreviews.com/forums/(E-Mail Removed)

Brad Smith
Systems Administrator
(E-Mail Removed)

brjsm Wrote:
> I am in the same boat. I don't have the Altigen VoIP card installe
> yet,
> but I am gearing up for it. The technician is installing the card
> tomorrow. I have 2 Cisco ATA 186 boxes ready to configure.
>
> So far I have configured the two boxes with the latest h.323 imag
> (3.1.2)
> and assigned static IP addresses (for testing). I then went into the
> config page (http://ww.xx.yy.zz/dev) and set the UID0 field as 4000 o
> one
> box, and 4001 on the other. I am able to call the other phone directly
> using the following syntax: 4001**w*x*y*z# where wxyz represents th
> ip
> address.
>
> The next step is to configure the boxes to register with the altigen
> server as the gatekeeper and gateway.
>
> Hope this helps. Share your experiences too! I am still working o
> this.
>
> -Bra


--
brjsm
 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Comunications ATA 186 to ATA 186 (without any gatekeeper or CallManager) SoGo VOIP 1 03-12-2005 07:39 AM
Cisco ATA 186 VOIP configure multiple itsp fwd/pulver me@privacy.net VOIP 0 12-15-2003 02:37 PM
Cisco ATA 186 VOIP configure multiple itsp fwd/pulver me@privacy.net Cisco 0 12-15-2003 02:37 PM
Cisco ATA 186 VOIP configure multiple itsp fwd/pulver me@privacy.net VOIP 0 12-14-2003 07:49 PM
Cisco ATA 186 VOIP configure multiple itsp fwd/pulver me@privacy.net Cisco 0 12-14-2003 07:49 PM



Advertisments