Velocity Reviews - Computer Hardware Reviews

Velocity Reviews > Newsgroups > Computing > VOIP > ISDN Wont Accept and Transfer PSTN Calls To CCM "bad bearercap" (AS5350-CCM)

Reply
Thread Tools

ISDN Wont Accept and Transfer PSTN Calls To CCM "bad bearercap" (AS5350-CCM)

 
 
anonyme
Guest
Posts: n/a
 
      01-28-2005

AS5350 Version 12.3(11)T2

I want to Transfer Calls From ISDN to CCM ,
The transfer call from PSTN to CCM doesn't work.
When I try I have a busy line.

I try this command on interface Serial3/0:15
"isdn incoming-voice Voice", but "voice" done % Invalid input detected

This is my config :
===================

version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname AS5350
!
boot-start-marker
boot system flash c5350-is-mz.123-11.T2.bin
no boot startup-test
boot-end-marker
!
enable secret
enable password
!
resource-pool disable
calltracker enable
calltracker history max-size 30
calltracker call-record verbose
spe default-firmware spe-firmware-1
no voice-fastpath enable
no aaa new-model
ip subnet-zero
!
ip cef
isdn switch-type primary-net5
isdn logging
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
cause-code legacy
h323
call start slow
!
fax interface-type fax-mail
!
controller E1 3/0
framing NO-CRC4
pri-group timeslots 1-16
!
interface Serial3/0:15
no ip address
isdn switch-type primary-net5
isdn send-alerting
isdn sending-complete
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.30.20
no ip http server
!
map-class dialer test
dialer voice-call
!
control-plane
!
voice-port 3/0
bearer-cap 3100Hz
!
voice-port 3/1
!
no mgcp timer receive-rtcp
no mgcp explicit hookstate
!
dial-peer voice 3000 voip
destination-pattern T
session target ipv4:192.168.30.205
incoming called-number 9762
dtmf-relay h245-alphanumeric
codec g711ulaw
!
dial-peer voice 1 pots
destination-pattern 0T
direct-inward-dial
port 3/0
!
ss7 mtp2-variant Bellcore 0
ss7 mtp2-variant Bellcore 1
ss7 mtp2-variant Bellcore 2
ss7 mtp2-variant Bellcore 3
!
line con 0
line aux 0
line vty 0 4
password xxx
login
line 1/00 1/59
no flush-at-activation
modem InOut
!
scheduler allocate 10000 400
ntp clock-period 17180058
ntp server 64.112.189.11
end

The debug and the error :
=========================
AS5350#sh debug


The following ISDN debugs are enabled on all DSLs:

debug isdn error is ON.
debug isdn event is ON.
debug isdn q931 is ON. (filter is OFF)
debug isdn silent errors is ON.


AS5350#
*Jan 1 18:13:24.376: ISDN Se3/0:15 Q931: RX <- SETUP pd = 8 callref =
0x0014
Bearer Capability i = 0x9090A3
Standard = CCITT
Transer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838C
Exclusive, Channel 12
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x1081, '37797912345'
Plan:Unknown, Type:International
Called Party Number i = 0x81, '9762'
Plan:ISDN, Type:Unknown
Sending Complete
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
1/0x12 calltype 2 CALL_INCOMING
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: call_incoming: call_id
0x0012, Guid = Se3/0:15
*Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
call id 0x12 with a bad bearercap from 37797912345 on b channel 12
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
1/0x12 calltype 2 CALL_CLEARED
*Jan 1 18:13:24.380: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8
callref = 0x8014
Cause i = 0x80D8 - Incompatible destination
 
Reply With Quote
 
 
 
 
Andreas Sikkema
Guest
Posts: n/a
 
      01-28-2005
anonyme <(E-Mail Removed)> wrote in news:41fa209c$0$20494
$(E-Mail Removed):

> *Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
> call id 0x12 with a bad bearercap from 37797912345 on b channel 12


You're receiving calls with bearer capability data, but expecting only
voice?

--
Andreas
 
Reply With Quote
 
 
 
 
anonyme
Guest
Posts: n/a
 
      01-28-2005

Andreas Sikkema wrote:
> anonyme <(E-Mail Removed)> wrote in news:41fa209c$0$20494
> $(E-Mail Removed):
>
>
>>*Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
>>call id 0x12 with a bad bearercap from 37797912345 on b channel 12

>
>
> You're receiving calls with bearer capability data, but expecting only
> voice?
>

Hi Andreas,

Yes, for the moment I want only receive voice call

Thanks in advance
 
Reply With Quote
 
plugas plugas is offline
Junior Member
Join Date: May 2008
Posts: 1
 
      05-02-2008
I have the same problem:
.May 2 18:47:58.519: ISDN Se3:15 **ERROR**: call_incoming: Received a call id 0xB95 with a bad bearercap from 25554469 on b channel 17
.May 2 18:47:58.523: ISDN Se3:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8046
Cause i = 0x80D8 - Incompatible destination

but I'm not cisco operator. So, what do I have to ask to change on cisco?
Bearer capability si wrong in this case?
 
Reply With Quote
 
ninop ninop is offline
Junior Member
Join Date: May 2008
Location: Venezuela
Posts: 3
 
      05-09-2008
ok, I think it's inside the serial 3/0:15 config:

try asking the router about the available options, like this:
===
router(config-if)#isdn incoming-voice ?
data Incoming voice calls will be handled as data.
modem Incoming voice calls will be handled as modems.
voice Incoming voice calls will be handled as voice.
===

then, select isdn incoming-voice voice

as example, this is my config, of my working cisco 3600 with a NM-HDV:

====
interface Serial1/0:15
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-qsig
isdn protocol-emulate network
isdn incoming-voice voice <-- Here I had to put this one so the calls are only voice, not data.
no isdn T309-enable
isdn T310 60000
isdn send-alerting
isdn bchan-number-order ascending
isdn outgoing display-ie
no cdp enable
=======

Hope this helps.
 
Reply With Quote
 
 
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
pc with isdn modem not connecte isdn 1841 router with isdn module sync Cisco 0 06-05-2007 10:10 AM
CCM - Incoming Cingular mobile calls don't hear ring josephdc@gmail.com Cisco 0 04-13-2007 05:12 PM
Best wireless voip router - accept pstn in and multiple voip out - on one handset Jim UK VOIP 23 05-08-2006 01:02 PM
2600 + 4BRI: can I accept V.120 ISDN calls from GSM network ? Help! Gio Cisco 1 02-23-2004 04:29 PM
2620 rtr, WIC-1-BU module, ISDN BRI, accept analog modem calls??? wr Cisco 1 02-02-2004 12:35 AM



Advertisments