«

Hi,

I am having trouble getting a PRI up between an Avaya Definity G3 PBX
and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
shows "up up".

My gateway is registered with CallManager just fine, but I'm pretty
sure this is simply an ISDN issue. I have the PBX setup as ISDN "user"
side and the 2611 as ISDN "network" side. We are using National/NI2.
The Definity is configured as Country code 1, Protocol version a. Does
anyone know if this is correct? Also, should the "Connect" version on
the PBX be "pbx" or "line-side"??

When I do a "show isdn status" the Layer 2 state of "TEI_ASSIGNED" is
a problem in my mind - I think this should be
"MULTIPLE_FRAME_ESTABLISHED."

Thanks - Rob.


Gateway1#sho isdn status
Global ISDN Switchtype = primary-ni

%Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
apply

ISDN Serial1/0:23 interface
******* Network side configuration *******
dsl 0, interface ISDN Switchtype = primary-ni
L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x807FFFFF
Number of L2 Discards = 0, L2 Session ID = 94
Gateway1#
Gateway1#
Gateway1#
Gateway1#sho ip int brief
Interface IP-Address OK? Method Status
Prot
ocol
FastEthernet0/0 10.10.4.50 YES NVRAM up
up

FastEthernet0/1 10.10.5.50 YES NVRAM up
up

Serial1/0:0 unassigned YES unset down
down

Serial1/0:1 unassigned YES unset down
down

Serial1/0:2 unassigned YES unset down
down

(snip)

Serial1/0:21 unassigned YES unset down
down

Serial1/0:22 unassigned YES unset down
down

Serial1/0:23 unassigned YES NVRAM up
up
Gateway1#
Gateway1#
Gateway1#sho run

(some non-relevant config snipped)

!
network-clock-participate slot 1
no network-clock-participate wic 0
network-clock-select 1 T1 1/0
network-clock-select 2 T1 1/1
!
isdn switch-type primary-ni
voice-card 1
!
ccm-manager redundant-host 10.219.16.1
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 10.219.16.1
ccm-manager config
!
!
controller T1 1/0
framing esf
fdl att
linecode b8zs
pri-group timeslots 1-24 service mgcp
!
interface Serial1/0:23
no ip address
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
voice-port 1/0:23
!
mgcp
mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
!
dial-peer voice 1 pots
application mgcpapp
port 1/0:23
!

This may get you closer to what you want. I have a PRI on a 3620.

Brian LaVallee

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3620-IS-M), Version 12.3(1a), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 05-Jun-03 17:53 by dchih
Image text-base: 0x60008950, data-base: 0x6187C000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

Router uptime is 10 weeks, 23 hours, 56 minutes
System returned to ROM by power-on
System image file is "flash:c3620-is-mz.123-1a.bin"

cisco 3620 (R4700) processor (revision 0x81) with 59392K/6144K bytes of
memory.
Processor board ID 25119094
R4700 CPU at 80Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 Channelized T1/PRI port(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=


Current configuration : 1646 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Hostname
!
boot system flash c3620-is-mz.123-9.bin
enable secret 5 xXxXxXxXxXxXxXxXxXxXxXxXxXxXxXxX
enable password xXxXxXxX
!
voice-card 1
!
ip subnet-zero
!
ip name-server NNN.NNN.NNN.NNN
!
isdn switch-type primary-ni
isdn voice-call-failure 0
!
voice hunt user-busy
voice call carrier capacity active
!
voice service voip
signaling forward unconditional
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
sip
!
voice class codec 99
codec preference 1 g711ulaw
codec preference 2 g729r8
!
no voice hpi capture buffer
no voice hpi capture destination
!
controller T1 1/0
framing sf
linecode ami
!
interface FastEthernet0/0
ip address NNN.NNN.NNN.NNN 255.255.255.240
speed auto
full-duplex
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 NNN.NNN.NNN.NNN
!
dialer-list 1 protocol ip permit
!
dial-peer cor custom
!
dial-peer voice 1 voip
huntstop
preference 2
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 99
session protocol sipv2
dtmf-relay rtp-nte
no vad
!
dial-peer voice 2 pots
preference 2
application session
destination-pattern ..........
translate-outgoing called 300
no digit-strip
direct-inward-dial
forward-digits all
!
sip-ua
retry invite 2
retry response 3
retry bye 3
retry prack 6
timers expires 300000
sip-server ipv4:NNN.NNN.NNN.NNN
no transport tcp
!
line con 0
logging synchronous
line aux 0
line vty 0 4
password 7 xXxXxXxXxXxXxX
logging synchronous
login
!
end

"Rob" <> wrote in message
news: om...
> Hi,
>
> I am having trouble getting a PRI up between an Avaya Definity G3 PBX
> and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
> crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
> shows "up up".
>
> My gateway is registered with CallManager just fine, but I'm pretty
> sure this is simply an ISDN issue. I have the PBX setup as ISDN "user"
> side and the 2611 as ISDN "network" side. We are using National/NI2.
> The Definity is configured as Country code 1, Protocol version a. Does
> anyone know if this is correct? Also, should the "Connect" version on
> the PBX be "pbx" or "line-side"??
>
> When I do a "show isdn status" the Layer 2 state of "TEI_ASSIGNED" is
> a problem in my mind - I think this should be
> "MULTIPLE_FRAME_ESTABLISHED."
>
> Thanks - Rob.
>
>
> Gateway1#sho isdn status
> Global ISDN Switchtype = primary-ni
>
> %Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
> apply
>
> ISDN Serial1/0:23 interface
> ******* Network side configuration *******
> dsl 0, interface ISDN Switchtype = primary-ni
> L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x807FFFFF
> Number of L2 Discards = 0, L2 Session ID = 94
> Gateway1#
> Gateway1#
> Gateway1#
> Gateway1#sho ip int brief
> Interface IP-Address OK? Method Status
> Prot
> ocol
> FastEthernet0/0 10.10.4.50 YES NVRAM up
> up
>
> FastEthernet0/1 10.10.5.50 YES NVRAM up
> up
>
> Serial1/0:0 unassigned YES unset down
> down
>
> Serial1/0:1 unassigned YES unset down
> down
>
> Serial1/0:2 unassigned YES unset down
> down
>
> (snip)
>
> Serial1/0:21 unassigned YES unset down
> down
>
> Serial1/0:22 unassigned YES unset down
> down
>
> Serial1/0:23 unassigned YES NVRAM up
> up
> Gateway1#
> Gateway1#
> Gateway1#sho run
>
> (some non-relevant config snipped)
>
> !
> network-clock-participate slot 1
> no network-clock-participate wic 0
> network-clock-select 1 T1 1/0
> network-clock-select 2 T1 1/1
> !
> isdn switch-type primary-ni
> voice-card 1
> !
> ccm-manager redundant-host 10.219.16.1
> ccm-manager mgcp
> ccm-manager music-on-hold
> ccm-manager config server 10.219.16.1
> ccm-manager config
> !
> !
> controller T1 1/0
> framing esf
> fdl att
> linecode b8zs
> pri-group timeslots 1-24 service mgcp
> !
> interface Serial1/0:23
> no ip address
> isdn switch-type primary-ni
> isdn protocol-emulate network
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> no cdp enable
> !
> voice-port 1/0:23
> !
> mgcp
> mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
> !
> dial-peer voice 1 pots
> application mgcpapp
> port 1/0:23
> !

Hi,

I am planning to inegrate a Definity PBX with a 2611 router .Can you send
me the config for Definity and where should I port the PRI on Definity ?

Thanks,
Mike

-------------------------------------
Rob wrote:


> Hi,

> I am having trouble getting a PRI up between an Avaya Definity G3 PBX
> and my 2611 voice gateway. I'm 99% sure I have the correct cable (a T1
> crossover cable) as Layer 1 of the PRI is active and port ser1/0:23
> shows "up up".

> My gateway is registered with CallManager just fine, but I'm pretty
> sure this is simply an ISDN issue. I have the PBX setup as ISDN
> "user"
> side and the 2611 as ISDN "network" side. We are using
> National/NI2.
> The Definity is configured as Country code 1, Protocol version a. Does
> anyone know if this is correct? Also, should the "Connect"
> version on
> the PBX be "pbx" or "line-side"??

> When I do a "show isdn status" the Layer 2 state of
> "TEI_ASSIGNED" is
> a problem in my mind - I think this should be
> "MULTIPLE_FRAME_ESTABLISHED."

> Thanks - Rob.


> Gateway1#sho isdn status
> Global ISDN Switchtype = primary-ni

> %Q.931 is backhauled to CCM-MANAGER on DSL 0. Layer 3 output may not
> apply

> ISDN Serial1/0:23 interface
> ******* Network side configuration *******
> dsl 0, interface ISDN Switchtype = primary-ni
> L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
> Layer 1 Status:
> ACTIVE
> Layer 2 Status:
> TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
> Layer 3 Status:
> 0 Active Layer 3 Call(s)
> Active dsl 0 CCBs = 0
> The Free Channel Mask: 0x807FFFFF
> Number of L2 Discards = 0, L2 Session ID = 94
> Gateway1#
> Gateway1#
> Gateway1#
> Gateway1#sho ip int brief
> Interface IP-Address OK? Method Status
> Prot
> ocol
> FastEthernet0/0 10.10.4.50 YES NVRAM up
> up

> FastEthernet0/1 10.10.5.50 YES NVRAM up
> up

> Serial1/0:0 unassigned YES unset down
> down

> Serial1/0:1 unassigned YES unset down
> down

> Serial1/0:2 unassigned YES unset down
> down

> (snip)

> Serial1/0:21 unassigned YES unset down
> down

> Serial1/0:22 unassigned YES unset down
> down

> Serial1/0:23 unassigned YES NVRAM up
> up
> Gateway1#
> Gateway1#
> Gateway1#sho run

> (some non-relevant config snipped)

> !
> network-clock-participate slot 1
> no network-clock-participate wic 0
> network-clock-select 1 T1 1/0
> network-clock-select 2 T1 1/1
> !
> isdn switch-type primary-ni
> voice-card 1
> !
> ccm-manager redundant-host 10.219.16.1
> ccm-manager mgcp
> ccm-manager music-on-hold
> ccm-manager config server 10.219.16.1
> ccm-manager config
> !
> !
> controller T1 1/0
> framing esf
> fdl att
> linecode b8zs
> pri-group timeslots 1-24 service mgcp
> !
> interface Serial1/0:23
> no ip address
> isdn switch-type primary-ni
> isdn protocol-emulate network
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> no cdp enable
> !
> voice-port 1/0:23
> !
> mgcp
> mgcp call-agent 10.219.17.1 service-type mgcp version 0.1
> !
> dial-peer voice 1 pots
> application mgcpapp
> port 1/0:23
> !





##-----------------------------------------------#
Article posted with Cabling-Design.com Newsgroup Archiv
http://www.cabling-design.com/forum
no-spam read and post WWW interface to your favorite newsgroup -
comp.dcom.sys.cisco,comp.dcom.voice-over-ip - messages and counting
##-----------------------------------------------##