err messages during make install-doc
 

Mac.

I installed readline, then I followed the directions for installing ruby
1.8.6. I ran "sudo make install" - no errors. When I ran "make
install-doc", I get the following errors:

No definition for proc_getpgrp
.................................................. ........
random.c: ..
range.c: c................
re.c: ccc....................................
regex.c:
ruby.c:
signal.c: m....
No definition for interrupt_init

Re: err messages during make install-doc
 

2009/2/2 Mark Miller <mjmiller18@go.com>:
> Mac.
>
> I installed readline, then I followed the directions for installing ruby
> 1.8.6. I ran "sudo make install" - no errors. When I ran "make
> install-doc", I get the following errors:
>
> No definition for proc_getpgrp
> .................................................. ........
> random.c: ..
> range.c: c................
> re.c: ccc....................................
> regex.c:
> ruby.c:
> signal.c: m....
> No definition for interrupt_init
> .
> sprintf.c:
>
>
> followed later by these errors:
>
> socket.c: ccccccccccm.
> No definition for bsock_do_not_rev_lookup
> .
> No definition for bsock_do_not_rev_lookup_set
> .
> No definition for bsock_s_for_fd
> .
> No definition for bsock_close_read
> .
> No definition for bsock_close_write
> .
> No definition for bsock_shutdown
> ...
> No definition for bsock_getsockname
> .
> No definition for bsock_getpeername
> .
> No definition for bsock_send
> .
> No definition for bsock_recv
> ..
> No definition for ip_addr
> .
> No definition for ip_peeraddr
> .
> No definition for ip_recvfrom
> .
> No definition for ip_s_getaddress
> ...
> No definition for socks_init
> .
> No definition for socks_s_close
> .
> No definition for tcp_accept
> ..
> No definition for tcp_sysaccept
> .
> No definition for tcp_svr_init
> ..
> No definition for udp_init
> .
> No definition for udp_connect
> .
> No definition for udp_bind
> .
> No definition for udp_send
> ..
> No definition for unix_init
> .
> No definition for unix_path
> .
> No definition for unix_addr
> .
> No definition for unix_peeraddr
> .
> No definition for unix_recvfrom
> .
> No definition for unix_send_io
> .
> No definition for unix_recv_io
> .
> No definition for unix_s_socketpair
> .
> No definition for unix_s_socketpair
> .
> No definition for unix_svr_init
> .
> No definition for unix_accept
> ..
> No definition for unix_sysaccept
> ..
> No definition for sock_initialize
> ..........
> No definition for sock_s_socketpair
> .
> No definition for sock_s_socketpair
> .
> No definition for sock_gethostname
> ..
> No definition for sock_s_gethostbyaddr
> ...
> No definition for sock_s_getnameinfo
> .
> No definition for sock_s_pack_sockaddr_in
> .
> No definition for sock_s_pack_sockaddr_in
> .
> No definition for sock_s_unpack_sockaddr_in
> .
> No definition for sock_s_pack_sockaddr_un
> .
> No definition for sock_s_pack_sockaddr_un
> .
> No definition for sock_s_unpack_sockaddr_un
>
> stringio.c: c................................................. ....
>
>
>
> Running the command "ruby -v" tells me I've got version 1.8.6. What are
> these errors and should I be worried?

This is output from the documentation generator.
Maybe the socket api is not properly documented.
Nothing to be worried about.

Stefan